DELTA 37-365X 8'' Precision Jointer DJ-20  Zoom

DELTA 37-365X 8'' Precision Jointer DJ-20

Item #: 26504
$2,299.99
Each No Longer Available
  • Note: Direct Ship Item - Shipped from manufacturer
  • Estimated Delivery time: 14 business days.
  • Must be shipped within 48 Contiguous United States
  • Please call customer service before returning a direct ship product.
  • The carrier will need to know if delivery is to a residential address (we'll ask you about that during checkout). There is no charge for this
  • There is an additional $120.00 shipping charge for this item.
  • A $30 lift gate fee will be added if a loading dock is not available. Please indicate if you need a lift gate.

Overview

The DELTA 37-365X includes 1-1/2 HP, 120/240 Volts, 60 hz, Single Phase motor, 3-knife cutterhead module, cutterhead guard with wrenches, rabbeting ledge, tilting fence, push blocks, two pulleys, instruction manual, **Runs on sealed, lubricated-for-life ball bearings
  • Unique parallelogram support system allows the table to move in the same arc as the cutterhead when raised or lowered. This uniform, close clearance to the cutting blade acts as a more efficient chip breaker.
  • Cast-iron assures less vibration; cabinet stand completely encases motor and pulleys to protect from dust and shavings.
  • Specially-designed cast-iron fence is extra long for continued support throughout the cut. Fence is center-mounted and functions as a rear guard on narrow cuts.
  • Modular cutterhead provides a consistently clean cut. Jack-screw arrangement allows easy replacement and adjustment of individual knives. In the event the entire cutterhead has to be removed, a new module can be fitted in place without production down-time.
  • Extra-long infeed table provides a full 76-1/2" of work support.


  • Motor: 1-1/2 HP, 120/240V (wired 240V), 60 hz, 1 Phase TEFC, 3450 RPM
  • Cut Capacity - Width: 8" (203 mm)
  • Cut Capacity - Depth: 5/8" (16 mm)
  • Rabbeting Capacity: 5/8" (16 mm)
  • Cutterhead Speed: 5,500 RPM; 16,500 CPM
  • Number of Knives: 3
  • Cutterhead Diameter: 3-3/8" (86 mm)
  • Table Size: 76-1/2" (1943 mm)
  • Table Length of front table (Infeed): 42" (1067 mm)
  • Table Length of Rear Table (Outfeed): 32" (813 mm)
  • Table Height: 32" (813 mm)
  • Fence Size: 5" x 35" (127 x 889 mm)
  • Fence Tilt: 45° in and out
  • Fence Positive Stops: 90°, 45° in and out
  • Dust Port Diameter: 4
  • Width: 26" (660 mm)
  • Height: 32" (813 mm)
  • Length: 76-1/2" (1943 mm)
  • Weight: 394 lbs (179 kg)
  • Warranty: 5 Year Warranty

Tech Spec

Brand Delta
Manufacturer Part Number 37-365X
Weight (lbs) 0.0000
Jointer Cutterhead Speed 5500 RPM
Dust Collection 4" Port
HP 1-1/2 HP
Size 8"

Reviews

Customer Reviews

2 Review(s)

View All

I had owned and used this...

Michael V from Bismarck, IL Posted June 22, 2011
I had owned and used this machine for over 15 years. I sold out when I moved, and recently relocated. I purchased a new DJ-20 for my new shop. My unit was perfect right out of the box. I went over it with a Starrett straight edge and machinist quality squares. I found the instruction book helpful and assembly was a piece of cake. The proof was in the "puddin" when I put this machine to work on building a large quarter saw white oak Mission style dresser. I purchased my machine from my local Rockler dealer and was pleased with the service.

The unit has good capacity and...

david t from Trelford, AZ Posted May 27, 2008
The unit has good capacity and mostly quality components. It can flatten a 5 foot by 8" board without tipping off the surface. And it can give you a smooth surface for edge gluing, but it can't do any of that out of the box. I had to do a complete set up and tune up once my unit was unpacked. I was given no reason in the instructions why they provided three pulley wheels. My fence was warped approx. 12 to 15 thousands so it's difficult to get a square edge. There were no instructions included about how to tune up the machine beyond just the basic principles. I had to reset and/or adjust the cutter head, the front (or infeed)table, it wasn't parallel to the cutter head, the outfeed table was way out of alignment, adjusting the proper height was one thing but it was twisted and sloped at the same time. The knifes were not even parallel to their own cutterhead.After following the instructions to the letter I fould that the rear fence was pushing down on the outfeed table and causing it to drop no matter how tight I firmed up the locking knob. It also drags across the outfeed table leaving a scratch. I finally ended up using a file and removing some excess material. When I tighten the rear fence it always moves so I have to accomodate for this and make it not square so it will be square when it is tightened. For this kind of money I shouldnt have to modify and rework parts to get it to do it's job. The quality of this company has gone so far down hill I don't think they will recover. Maybe these should be built here in the States so we can keep an I on quality control and give loyal customers their moneys worth again like we did in the past. Oh yea, one more thing, I tried calling Delta's customer service for help. I was on hold for a few minutes short of eternity. I called back twice and was treated very rude. Can the people at Delta actually believe they did me a favor by taking my money? Next time I'm going to look very closely and probably buy another competitive brand.

Write Your Own Review

Only registered users can write reviews. Please, log in or register

Videos

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012
Feedback X