Electronic Digital Readout for Portable Planers  Zoom

Electronic Digital Readout for Portable Planers

Item #: 24036
$65.99
Each In Stock

Overview

Affordable attachment accurately displays the thickness of the board exiting the planer.
  • Eliminates the need for tape measure or calipers.
  • Measurements in inches or mm.


Features absolute measuring mode with memory and incremental mode that re-sets to 0.000" or 0.00 mm.

  • Calibrates in seconds.
  • Fits portable planers from DeWalt, Delta, Ridgid, Ryobi, Craftsman and more.
  • Mounts in minutes.
  • Includes readout, stainless steel scale, graphic scale sticker, sheet metal mounting parts, hardware and manual.
  • Now uses AAA Batteries for operation (included). Provides up to 2 years of battery life.

Tech Spec

Brand Wixey
Manufacturer Part Number WR510
Weight (lbs) 1.1000

Technical Downloads:

Reviews

Customer Reviews

3 Review(s)

View All

Installation

Daniel Posted January 1, 2015
This review is based upon Model wr510 type 2 and installed on Ridged surface planer. The instructions that came with the planer is a little small, so my suggestion is go to Wixey's web site and through Acrobat Reader print out a full page instructions.
Now for the review: After removal of 2 screws from the pointer than reinstall with double washer. Problem 1: the two original screws slips through the double washer; solution: use small washers in between double washer and screw head. It was suggested by the instructions to drill into the holes from which the screws came from (the pointer). Best not to do since it is part of the machine (just a suggestion). Problem 2: It is stated that "Loosely attach the lever using the m6 bolt and hex nut followed by lining up the top of readout case to match the planers height setting and then tighten screw. Then the following tighten all screws and check for free movement of the scale." If scale binds, loosen and re-tighten screws or carefully bend brackets. My suggestion and it is only my suggestion and was done on my machine, bought M6 screw about an inch long with a couple of m6 washers and placed them in between "the lever bracket", no bending needed. Problem 3: it mentioned to plane down a board to what ever thickness and mark on that board as go to place for your caliper, (again my opinion, not consistant for thickness). Solution: use brass bars that have known thicknesses, this will give more exact measurement and consistancy. Problem 4: if a readout gives a negative number that is ok but when planning down to desired thickness can be confusing. Solution; place one of those brass bars, example 1/2" between the foot fot frame and rounded end of the scale and press and hold for about 3 sec. to set to zero, remove brass bar and let scale rest on the foot of the frame. That measurement will show a positive 1/2". That new measurement will be your go to as starting point to plane down a board to thickness as needed. Also, the suggestion in the instructions as an option was to make the scale permanent by drilling holes into machine and using the screws as provided. My opinion is not to do that because if down the line you wish or remove that digital scale and use the original rule as provided on the machine will now have to holes in that ruler. Please remember, these were only suggestion and my experience with the Ridgid planer I have. Hope these suggestions help.

Thickness planer digital readout

Michael Posted October 4, 2014
Installation on a Dewalt model 733 was fairly easy however I would not rely on only the double stick tape for mounting; I also used the self tapping screws. The unit works quite well but have not yet used it extensively so can't comment further.

Thickness Planer

Tim L Posted September 8, 2014
Got this to use on the Dewalt DW734 Planer to help with more accuracies of the planer. Have not used this yet but have studied it and appears to be real easy to install.

Write Your Own Review

Only registered users can write reviews. Please, log in or register

Videos

What People are Saying:

I have been using Rockler for years, your products are always the best that can be purchased and your prices are very reasonable. Ann you have always done your best to make me feel as though I was your very best customer. Thank you for great service."

- Daniel F.

What People are Saying:

I have been using Rockler for years, your products are always the best that can be purchased and your prices are very reasonable. Ann you have always done your best to make me feel as though I was your very best customer. Thank you for great service."

- Daniel F.
Feedback X