Overview
Operates smoothly, prevents sagging or binding and allows a wide range of leaf openings. 36'' slides are ideal for large rectangular tables. Gives maximum opening of 38 or 64''. Generally the length of the closed slides should be at least 2/3rds the length of the closed table. Sold in pairs. Available in wood or steel.
Frequently Bought Together
Questions and Answers
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 38 questions
Browse 38 questions
and 97 answers
Why did you choose this?
Rockler Store
this will be my second table to repair a sagging top.
Francis B
on Jul 17, 2017
Replace wooden extension, table starting to sag.
Kenneth L
on Mar 22, 2017
this will be my second table to repair a sagging top.
Francis B
on Jul 17, 2017
Sliding dining table "64" closed with two extension leaves of 15" wide/ea. I believe the 36"extension slides will work, as the info says they will provide a 38" opening. If I'm wrong please inform me. Old wood slides not working.
Dennis D. N
on May 23, 2017
Sliding dining table "64" closed with two extension leaves of 15" wide/ea. I believe the 36"extension slides will work, as the info says they will provide a 38" opening. If I'm wrong please inform me. Old wood slides not working.
Dennis D. N
on May 23, 2017
Wanted lots of room to grwo
Clark D
on Feb 26, 2017
What is largest leaf opening? I have two 18" leafs on a round single pedestal table
For a heavy table with two 12" leaves, which would be better, steel or wood? Wood would look better on this vintage table, but performance trumps appearance!
BEST ANSWER: I also have a vintage, homemade heavy table with two of the same sized leaves. Quite frankly, I wish I had gone with steel. We only put the leaves in twice a year, so hopefully will be OK. I may need to make a temp. 5th middle leg for when all the leaves are inserted. If you have the money, go for steel. As to appearance, you'll only see it when adding/removing leaves, and then only for a few seconds.
Brad
Brad
- Reply
- Inaccurate
- Brad R on Nov 26, 2015
- Purchased on May 1, 2015
Is the Leaf opening 62"?
BEST ANSWER: The opening I believe is 64 Inches. The table I made was 120 inches, I used three table leaves 20 inches each a total of 60 inches.
- Reply
- Inaccurate
- John H on Mar 3, 2016
- Purchased on May 7, 2015
Can these be used on an outdoor patio table?
BEST ANSWER: I got the wood slides. While technically I guess they could be used outdoor, personally I wouldn't since the wood would expand and shrink in the different weathers. I'd get metal if it was me. However, I'm no expert.
We're still happy with our two slides that I put on the dining room table a couple of years ago.
We're still happy with our two slides that I put on the dining room table a couple of years ago.
- Reply
- Inaccurate
- Brad R on Nov 3, 2016
- Purchased on May 1, 2015
I just received my replacement slides, for screw installation, the technical data refers me to table pins--how do I find this reference material?
BEST ANSWER: For table pins see http://www.rockler.com/table-pins-choose-type
- Reply
- Inaccurate
- Steve Staff on Aug 10, 2015
Is the hardware included with the slides? And, are there instructions for proper placement with dimensions? Thank you!
BEST ANSWER: Screws are not included. For instructions on installation click on the link under the Technical Downloads heading of this web offer.
- Reply
- Inaccurate
- Steve Staff on Jul 7, 2015
Is the 36" extension slide more than adequate for accommodating (2) 14" table leafs ?
BEST ANSWER: I'm no expert. That being said, I did put them on our table, to replace two that had broken. Our two leaves are 12" each, there is enough room for 14". HOWEVER, if I had to do it over again, I wouldn't buy these slides that are made from wood. I would buy the ones made from metal. We only use our table twice a year in the fully extended position, so it really doesn't make a big difference, but already I can see the table bowing down. Just a thought.
- Reply
- Inaccurate
- Brad R on Dec 29, 2015
- Purchased on May 1, 2015
I just order the steel extensions. I'm making a table from scratch. When I look at the installation instructions it appears that the table legs will move apart when I'm opening up the extenders (vs a stationary base). Is this correct?
BEST ANSWER: correct. I used these on a 42" square antique table with its 4 legs and one center leg. This table now seats 12 people instead of just four, when opened. It has four legs, and one center leg. When you open it, the center leg can remain in place, and support the middle, as this extends pretty far. Worth the money.
- Reply
- Inaccurate
- Richard K on Jul 17, 2017
- Purchased on Oct 21, 2015
Can I sister these next to existing wooden extension slides such that I don't have to remove the existing slides, I can leave them in place?
BEST ANSWER: I'm no expert, but I don't see any reason these can't sister next to some existing slides, as long as you leave just a little room between the old ones and the new ones for expansion and contraction.
- Reply(1)
- Inaccurate
- Brad R on Dec 29, 2016
- Purchased on May 1, 2015
I have a 4-legged dining table that right now opens to accommodate one table leaf. But one leaf is no longer enough. Now with grandchildren I need to increase the size of the table. Can I change out the table slides with longer ones in order for the table to expand to accommodate 2 tables leaves instead of just one? Will the table sag in the center? Thank you for shedding some light on the matter.
BEST ANSWER: Yes, that is what I used these for. The slides are strong enough and won't sag. If you're inexperienced do your research and plan carefully, or hire a cabinet maker to do the work.
- Reply
- Inaccurate
- Christopher J on Apr 6, 2016
- Purchased on Dec 11, 2014
Can I mount the rails to the inside of a kitchen cabinet to produce a retractable working surface?
BEST ANSWER: As long as you don't overload the new working surface, I don't see why not. HOWEVER, that being said, most people push down / cut / etc down on working surfaces quite hard, and this 3 piece wooden slide would break in my opinion. You might want to go for the more expensive metal ones. Remember though, neither the wooden or the metal ones, were made to withstand much weight / pressure.
- Reply(1)
- Inaccurate
- Brad R on Jan 27, 2016
- Purchased on May 1, 2015
would this item work for a drop leaf table?
BEST ANSWER: The item is meant to extend a table's opening, and only for tables with 4 legs. It's meant to screw into the underside of the table, on both ends of the slide. If you use it to hold up the drop leaf portion, you'd probably want to attach it somehow. It's also meant to have 4 legs, so legs on both ends of the slide, something your drop leaf wouldn't have. I'm not an expert, but it doesn't look like it would work for a drop leaf table.
- Reply
- Inaccurate
- Brad R on Jun 30, 2015
- Purchased on May 1, 2015
I have a kitchen table with four legs and it has two leafs of 12" each. Is item 29694 the best to replace my broken slide?
BEST ANSWER: I used these (wooden) slides in a similar table and setup, and they worked perfectly. Great quality. Would definitely use again. Well worth the expense/time/trouble to buy these, rather than make them.
- Reply
- Inaccurate
- William E on May 21, 2015
- Purchased on Dec 1, 2014
Can the Steel slide be used for a table with 4 legs that has NO apron (in other words, it's just the top with 4 legs attached)? will this be very visible from the side? Also, the top is quite heavy - is there weight limit recommended for this hardware? thank you -
BEST ANSWER: I don't believe there is any weight limit on these glides. You can actually move them in a little further from the outside edge of the table which will conceal the visibility problem. But each one should only be a third of with of the table from the edge. The key to these working properly is to make sure they are perfectly parallel to each other. Otherwise when you pull them open they will bind and it will be hard to operate.
- Reply
- Inaccurate
- FINISH D on Jul 14, 2017
- Purchased on Sep 21, 2015
Where are the figures or diagrams referenced in the technical data and sheets that accompany the metal slides? They reference figures 5, 8, 9 etc, but only one diagram is included (and poor quality at that). I'm pretty sure I know which side is mounted adjacent to the table, but I want to be sure. The only figure included doesn't show enough detail.
BEST ANSWER: I had problems with these slides and had to return them. They jambed. I am pretty sure that the side with the raised edge is the side that mates with the underside of the table.
- Reply
- Inaccurate
- brent G on Apr 6, 2017
- Purchased on Jun 8, 2015
Can (should ) I stain the slides to match the the table? And Finnish with lacquer?
BEST ANSWER: Obvioiusly you can't stain the metal ones. It you want to stain the wooden ones, I don't see a problem, as long as you keep the stain out of the places the pieces slide against each other. This would be the same for any lacquer. Get either one in the groves, and you're going to have real problems operating your table. Personally, I wouldn't stain of lacquer them at all, who looks at the bottom of tables? Brad
- Reply
- Inaccurate
- Brad R on Sep 4, 2016
- Purchased on May 1, 2015
will the 36 inch ok to take two 18 inch leafs ?
BEST ANSWER: One thing that I learned was that the length of the slides should be approximately 3/4 of the length of the table when closed without the leaves. This is to provide adequate support for the table when the leaves are installed. the description of item 29496 states that it will open 38 inches thus allowing two18 in leaves to be inserted. However, I would install the longest slides that you can put in the table thus providing the most support. I am sure that you can picture that the farther the slides are open the less the male sliding dovetails are in their corresponding sockets thus less support when the leaves are installed. If your table has a center support leg that is in place with or without the leaves then that obviously changes things. I hope this helps.
- Reply
- Inaccurate
- Ronald D on Jan 15, 2016
- Purchased on Mar 24, 2015
how long are te slides overall when completely extended?
BEST ANSWER: I am sorry that I cannot help you, because the table that I used the slides on is 60-plus miles away in the dining room of a different home. .But, if I remember correctly, the slides were slightly over 72" when they were fully extended. The opening will be about 38" for the leaves and the ends will extend about 18" for attaching to the table ends. I hope this helps!
- Reply
- Inaccurate
- Bryan S on Jan 13, 2016
- Purchased on Dec 29, 2014
Which is lighter, the wood or steel version?
BEST ANSWER: Bought the wood version , now we can seat 8+people at the dining room table . Slides were a breeze to install, made an additional leaf for the table. Would recommend the wooden slide, was a good buy.
- Reply
- Inaccurate
- Daniel D on Nov 2, 2015
- Purchased on Dec 4, 2014
What is the total length of item #29504 when fully extended?
BEST ANSWER: 74 3/8" total length which gives 38" between the two halves.
You'll need to allow some space to drop the leaves plus any hardware.
You'll need to allow some space to drop the leaves plus any hardware.
- Reply
- Inaccurate
- Danny F on Dec 8, 2016
- Purchased on Nov 17, 2016
Can these extension slides be used on circular tables, as well?
BEST ANSWER: Yes I would think they could having the correct measurements.
- Reply
- Inaccurate
- Jim D on Apr 27, 2015
- Purchased on Apr 11, 2015
What is the closed length of the 62" extension? Do you have a picture of the entire slide?
BEST ANSWER: The specifications and dimensions are shown on the document located at: http://go.rockler.com/tech/29470-504.pdf
- Reply
- Inaccurate
- David Staff on Jul 18, 2017
are the steel extension slides #29702 made with ball bearings?
I am planning to build a table that is 10' at smallest and the customer would like it to extend to 13'or 14' will the extensions you carry be adequate? It says closed they should be 2/3 length of table. What are my options?
BEST ANSWER: Once the 36" slides are installed, the maximum amount of space for leaves is approx. 60". Starting with a 10' closed table makes these slides a bit skimpy for it, they work best for a 65" closed table, give or take a few inches. You need something longer and unfortunately probably much more expensive.
- Reply
- Inaccurate
- joseph m on Nov 29, 2016
- Purchased on Dec 11, 2014
I am restoring a table but on this table the ends of the table pull out and the 12" leaf is inserted between the end of the table and the middle section. My problem is that the ends droop down because of the looseness of the slides. I need 4 table slides that will not droop down with a 12" leaf in the table. If would be best if they are no more than 32" long closed. There needs to be very little play/tolerance so there will be no sag when extended. Are the smaller size made so they will not sag in this situation?
BEST ANSWER: These slides are not designed for the style of table you have. For the table design you describe one would typically use http://www.rockler.com/wooden-trestle-table-slides
- Reply
- Inaccurate
- Steve Staff on Apr 28, 2016
when I extend the table it seems to sag and doesn't seem strong. how do I fix that? The table is 6' long with only 1 12" leaf.
BEST ANSWER: I'm guessing that you haven't got the screws that fasten the extensions to the table tight. To reinforce the extensions, I added an L bracket at each end of each rail. With the table extended, check to see if you can see a gap between the table and the extensions.
- Reply
- Inaccurate
- Lowell Y on Mar 7, 2016
- Purchased on Feb 17, 2015
I have white oak I just had milled to 1inch and a half by 12 inches by 9 foot long and 1inch and a half by 12 inches by 6 foot long 6 pieces each I want to make a table with a leaf that is hidden under the table and can be utilized for Thanksgiving 9 foot can become 12 foot and I think I'm going to make the table 4' foot width. I need some good hardware for this project can you give me some options?
BEST ANSWER: We installed it on a table with three 12 inch leaves and it is rock solid. Don't know how you are going to store it under the table.
- Reply
- Inaccurate
- Glen J on Mar 7, 2016
- Purchased on May 10, 2015
I want my husband to convert a table into a console by cutting two leaves out of the middle of a dining table, place the two ends together with WHAT, and use these to make what will APPEAR TO BE a console in my living room. I'll store leaves, (WHERE, I DON'T KNOW) and be able to expand the table to sit 8 or 10 people so I can FINALLY have people over for dinner in this itty-bitty house! I'll use the 29686 slides (70") and the pegs. Any suggestions or hints? What am I forgetting or missing in this crazy (but wonderful) idea? I know I can buy this type of table, but home made ANYTHING is always better! :)
BEST ANSWER: I used this glides to add another lead to my table. Now my table is 98 in long and will accommodate 10 people. Simply replaced the old glides with these longer ones to accommodate 2 leaves. My son did this and it works great. Only took him a few minutes to change out the glides. Hope this helps
- Reply
- Inaccurate
- Joan M on Feb 24, 2016
- Purchased on Dec 20, 2014
I want my husband to convert a table into a console by cutting two leaves out of the middle of a dining table, place the two ends together with WHAT, and use these to make what will APPEAR TO BE a console in my living room. I'll store leaves, (WHERE, I DON'T KNOW) and be able to expand the table to sit 8 or 10 people so I can FINALLY have people over for dinner in this itty-bitty house! I'll use the 29686 slides (70") and the pegs. Any suggestions or hints? What am I forgetting or missing in this crazy (but wonderful) idea? I know I can buy this type of table, but home made ANYTHING is always better! :)
BEST ANSWER: If it has a veneer top, cut has to be do a special way. If it has an apron it must be dealt with. This project causes me more questions than I have answers to you.
- Reply
- Inaccurate
- N U on Feb 23, 2016
- Purchased on Dec 9, 2014
I have a oak ding table from 70s or 80s. The sliders are attached to the base with a small plate that has a hole in middle for scew. Unfortunately I have only two, need six. These go into groove of slide and when tightened secure it. Help! Can't seem to find anywhere?
BEST ANSWER: Take one to a sheet metal shop and have them fabricate more. Shouldn't cost much. Or you could fabricate them yourself by bending some band iron in a vise (to make the offset, or step, on the plate), or you could fabricate without bending and stack some washers between the tab and the screw to make the offset.
- Reply
- Inaccurate
- Christopher J on Jan 12, 2016
- Purchased on Dec 11, 2014
Reviews
4.9 / 5.0
29 Reviews
Very sturdy, smooth glding
I was skeptical when I opened the package, because each side attached with only 5 screws, but it seems to be holding. The rails are very sturdy - I used it for a massive farmhouse table with a 3" thick top and it doesn't flex or bend at all. Recommend.
- Was this review helpful? Yes (9) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (9) No (0)
- Flag as Inappropriate
I have built 120"x42" extension table using the Extension slides. they have worked very well. I have three leaves totaling 60" supported by them.
- Was this review helpful? Yes (5) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (5) No (0)
- Flag as Inappropriate
36" table slide for leaves
These slides are exactly what I wanted. They were shipped quickly as I had requested. They were easy to install, and worked well even though they do not have ball bearings. We used these to allow us to use two newly made 18" leaves in an older table that was originally made for leaves, but the leaves and the slides for that table were long gone. I was concerned that a 36" extension would make the table weak or unstable, but not true. With the two 36" leaves in place using these slides, that table did not droop or feel unstable in any way. Nice product.
- Was this review helpful? Yes (4) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (4) No (0)
- Flag as Inappropriate
Table extension slides
I found the slides to be simple to install and they work great.
- Was this review helpful? Yes (2) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (2) No (0)
- Flag as Inappropriate
fantastic
The slides worked perfectly. Once they were installed on our antique table of over one hundred years old they opened and closed easly and flawlessly. The table top sat very straight and flat. Table hadn't looked that good in years. Now we can all sit around it again for Thanksgiving dinner for many more years to come. Thanks for a great product at a great price!!
- Was this review helpful? Yes (2) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (2) No (0)
- Flag as Inappropriate
extension slides steel
the product is perfect. it added 60 inches to my table. i made two 30 inch leafs. cant wait for family at thanksgiving so we can all sit together. i will give it 5 stars all day long.
- Was this review helpful? Yes (2) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (2) No (0)
- Flag as Inappropriate
Fantastic Slides!
We replaced wooden slides with these and it made an enormous difference. The table is rock solid and opens and closes with minimal effort.
- Was this review helpful? Yes (2) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (2) No (0)
- Flag as Inappropriate
Strong but not quite as strong as I hoped
Pretty solid slides but not quite as solid as I hoped for an expected. I created a 6 foot table frame just to test their strength using 2x4s and at full extension(5+ feet opening) it was kind of weak. It held my full body weight but it had a couple inches of give to it. Even a little bit of pressure in the middle causes it to give an inch or two at full extension which isn't desirable for a table. To be fair it's not really designed for complete full extension; it merely opens that far to allow leaves to slide in and then you should collapse them back in at least a few inches. All that said, at a 4 foot opening, I found it to be very solid...very little give or flex. Let's face it, though, being that solid at 4 feet is still impressive. I am going to end up keeping them. Instead of a 6 foot to 11 foot table, I am adjusting my design to be 7 foot to 11 foot (4 foot expansion). I haven't built it yet but I have hopes that it will be a very solid table even when both 2 foot leaves are in.
- Was this review helpful? Yes (2) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (2) No (0)
- Flag as Inappropriate
Table extension mechanism replacement.
We were repairing an " antique" kitchen table - the wood on the extension mechanism was breaking when used.
The Rockler replacement was easy to install - instruction are on - line, not with the mechanism. The height was less than the old one so we had to add a piece to attach the center, 5th, sliding leg. No problem to do that.
Table now opens easily - and my wife wants me to make another leaf or two since it opens wider (and there is the center leg for support).
The Rockler replacement was easy to install - instruction are on - line, not with the mechanism. The height was less than the old one so we had to add a piece to attach the center, 5th, sliding leg. No problem to do that.
Table now opens easily - and my wife wants me to make another leaf or two since it opens wider (and there is the center leg for support).
- Was this review helpful? Yes (1) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (1) No (0)
- Flag as Inappropriate
36" Extension Slides
Worked perfectly. Metal slides are strong with no sag at full extension. Layout, square up and attach. Fabricate new leaves- you're done. Great product.
- Was this review helpful? Yes (1) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (1) No (0)
- Flag as Inappropriate
