Related Products
|
- Overview
- More Info
- Reviews
Just drill two holes to install these hinges.
|
Hidden Barrel Hinges are made of solid brass with brass plated steel connecting links. Metric measurement is the diameter of barrel. Price per pair.
Minimum wood thickness for hinges.
- 10mm is used on 1/2'' stock
- 12mm is used on 5/8'' stock
- 14mm is used on 3/4'' stock
- 18mm is used on 1'' stock
- 24mm is used on 1-1/4'' stock
To view tech info on all sizes click on view tech sheet link to 28555.
|
| |
Customer Reviews and Photos for:
Hidden Barrel Hinges
|
Average Rating:
(3.5)
(18 customer reviews)
Add your review...
|
|
|
1) Submitted by
Cary, from Vancouver, BC
on 6/2/2009
Customer Rating: 
I am very satisfied with these hinges for use in small boxes. They are durable, attractive and a snap to install with perfect alignment. I use the 10mm size, and mill the box sides a shade over 1/2" thick.
I have a few suggestions concerning installation. Firstly, it is a good idea to make a mockup, as shown in the photo in the top-left corner. You will see that, after drilling the holes for the hinges (but before installing the hinges), I've cut relief slots with a bandsaw (only in the mockup, of course). This allows me to remove the hinges by first twisting a slotted screwdriver in the corresponding slots. Without the slots, the hinges could not be removed without damaging the hinge or the box.
To drill the holes, first mark the backs of the top and side, as shown in the photo in the top-right. The marked faces are placed against the bandsaw fence. Next, a) postion the bandsaw fence so that the first holes drilled in the side will be approximately centred relative to the thickness of the material; b) position the (say) left fence stop so that the hole at the far end of the side is in the correct position; and c) set the depth stop on drill press so the hinge will bottom-out in the hole when it is fully-seated. This is shown in the photo in the bottom-left corner. Neither the fence nor left fence stop are subsequently moved. After drilling the first hole in the side, pivot the board around the end nearest the hole, bring the bit down into the hole and position the right fence stop, as shown in the photo in the bottom right corner. Now the hole can be drilled at the other end of the back side, after placing the board against the right stop, with the mark on the board facing the fence. After repositioning the depth stop for the holes to be drilled in the lid, the two holes are drilled in the lid, one using each fence stop. By keeping the marked sides of the boards against the fence and the ends against the fence stops, the holes, base and lid will align perfectly.
Lastly, when inserting the hinges, first make sure they are not put in (rotationally) backwards (i.e., ensure the lid will open after they are inserted). Then press them into the base and lid simultaneous and gradually, initially opening and closing the lid repeatedly, making small corrections to their rotational alignment, to make sure they are straight and not twisted. This is important, because you will not be able to straighten them in the holes after they are pressed in a very short distance (and you may not be able to remove them and start again). If the holes are drilled deeper than is necessary, care must be taken that one end of the hinge is not pressed in too far, as it cannot be pulled back. That is why it is best to test-drill the holes so that they are precisely as deep as is necessary for the hinges to bottom out when they reach the correct depth.
|
|
2) Submitted by
Bill Porada, from Thousand Oaks, CA
on 9/16/2008
I built this curly maple jewel box and dyed it with your "Burnt Sienna" dye. I had to mix it a bit more concentrated than what the directions recommended but I finally got the color I wanted. It turned out better than I thought. Note, I also used your barrel hinges and full mortise lockset. I like the way the project turned out.
|
|
3) Submitted by
Danny Aiu, from Honolulu, HI
on 10/27/2008
Customer Rating:
To keep students interested I need quick projects that give good results, this product did the job. We made small gift boxes from various woods and the hinge fit and function was great. We will be ordering more.
|
|
4) Submitted by
Andres Mendez, from Belmont, NC
on 5/5/2008
Customer Rating:
Got these to replace ones on an older desk that had fallen apart. Worked perfectly. Exactly what I needed. They installed easily into the holes the older hinges came out of.
|
|
5) Submitted by
David Knapke, from Highlands Ranch, CO
on 8/22/2009
Customer Rating: 
I used these for a small door for a hidden compartment in the back of a cabinet. The cabinet and door were plywood. The adjustment screws would not allow me to tighten the hinges in the hole well enough to keep the small door from sagging.
|
|
6) Submitted by
Steve, from McLean, VA
on 3/16/2008
Customer Rating:
Perfect! Exactly what I needed and wanted. Worked like a champ!
|
|
7) Submitted by
Joe, from Chicago, IL
on 12/9/2008
Customer Rating:
I've used these hinges on small boxes (jewelry, humidors, etc) and they excel when the lid sits on top, but for a door they were very poor. Even small doors sag and they have absolutely no adjustments. Also, once installed, they are very difficult to remove to realign. I will try to be sure my designs don't use these hinges for door. But the work really well for small tops and lids.
|
See all
18 reviews...
|
Home  Hardware Hinges Soss, Sepa and Barrel Hinges Hidden Barrel Hinges
|
|
CART
