Freud® Down-Spiral Router Bits - 1/2" Shank  Zoom

Freud® Down-Spiral Router Bits - 1/2" Shank

Downward spiral leaves clean, splinter-free edges for dados, grooves and rabbets.
product name price quantity total
1/2" D x 1-1/4" H x 1/2" Shank Freud #76-108 Down-Spiral Bit Item #: 37925
In Stock
 
$57.97

Each
$57.97
3/8" D x 1-1/4" H x 1/2" Shank Freud #76-106 Down-Spiral Bit Item #: 32413
In Stock
 
$50.97

Each
$50.97
1/2" D x 1-1/4" H x 1/2" Shank Freud #76-108 Down-Spiral Bit Item #: 37925
In Stock
 
Price:
$57.97
Each
Quantity:
Total: $57.97
3/8" D x 1-1/4" H x 1/2" Shank Freud #76-106 Down-Spiral Bit Item #: 32413
In Stock
 
Price:
$50.97
Each
Quantity:
Total: $50.97

Overview

This premium solid carbide bit cuts dadoes with crisp, clean edges on both sides of the dado. The downward spiral forces the chips down into the groove, eliminating the tendency for wood fibers to chip out the face. Also works great for cutouts and edgework. 1/2" shank.

Application: Grooves and dadoes in single-sided veneers and laminates.

  • Freud's solid carbide down spiral bits are ideal for smooth, chip-free routing where chip removal is not a problem.
  • Cuts all composition materials, plywoods, hardwoods, and softwoods.
  • Use on CNC and other automatic routers as well as hand-held and table-mounted portable routers.


Tech Spec

Brand Freud
Bit Type Spiral
Cutter Height 1-1/4"
Shank Size 1/2"

What's included:

(1) Freud Down-Spiral Router Bit

Reviews

Customer Reviews

3 Review(s)

View All

Freud down spiral bit is the...

Don C from Gabbs, NV Posted October 26, 2009
Freud down spiral bit is the best bit I have found for our application.Rockler's service and delivery is unsurpassed.

Used this router bit in combination...

Larry B from Morral, Ohio Posted July 6, 2008
Used this router bit in combination with a Dado Whiz dado cutting fixture to make four of the most perfect, most expensive dados that I have ever made before it broke. The cuts were 28 inches long in new plywood and came out perfectly in size and were splinter free on the face of the plywood - perfect - as long as it lasted. I figure that each cut cost about $12. I have no idea what may have happened to cause this bit to shatter but it did. I know that carbide bits won't take any abuse but this one didn't have any believe me.

I recently purchased two 3/8 down...

John P from Buford, GA Posted July 11, 2011
I recently purchased two 3/8 down spiral bits to go with my Rockler box joint jig. I was cutting box joints on 1/2 oak 12" wide. After hours of trying to get the joints to fit, it switched to the 3/8 bit that came with the jig and had no problem. The Freud bit was measured by a machinist and was found to be smaller than stated. The bits do not work with the jig.

Write Your Own Review

Only registered users can write reviews. Please, log in or register

Videos

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012
Feedback X