Freud® 99-569 Quadra-Cut™ Cove Raised Panel with Back Cutters Router Bit - 3-1/2" Dia x 1" H x 1/2" Shank  Zoom

Freud® 99-569 Quadra-Cut™ Cove Raised Panel with Back Cutters Router Bit - 3-1/2" Dia x 1" H x 1/2" Shank

Item #: 35240
$119.97
Each In Stock
Quadra-Cut design uses two upshear cutters to hog out the majority of the waste, while two downshear cutters clean up any fuzzing along the edges.

Overview

Freud's exclusive Quadra-Cut™ 4-cutter design provides the smoothest cuts possible. You'll get crisp, clean edges every time, even with cross-grain cuts in difficult materials. Use this panel raiser to mill panels from 3/4" stock that are flush with the door frame for a professional, architecturally correct appearance. The cove profile raised panel bit also includes a back cutter to cut the relief so the panel fits into the groove. This means there's no need to plane panels down to 5/8", saving wear and tear on your machinery. Shims are included to allow adjustment of tongue thickness from 7/32" to 1/4" for maximum versatility and compatibility. Produces a full 1-1/2" wide reveal for traditional raised panel doors.

  • Cuts all composition materials, plywoods, hardwoods and softwoods.
  • Use on table-mounted portable routers.



Tech Spec

Brand Freud
Manufacturer Part Number 99-569
Weight (lbs) 1.0000
Bit Type Raised Panel
Diameter 3-1/2"
Cutter Height 1"
Shank Size 1/2"
Flutes 4

What's included:

(1) Freud Quadra-Cut™ Cove Raised Panel Bit with Back Cutter

Technical Downloads:

Reviews

Customer Reviews

4 Review(s)

View All

The bit works great. However, if...

Jim B from Mesquite, TX Posted January 11, 2010
The bit works great. However, if you are doing arched or cathedral panels, Freud's technical staff recommends doing the end cuts in a single pass using at least a 3 hp router (and hold on tight!). A less exciting way was to remove the backcutter until the cove cuts were completed by making 2 passes. Then do a full pass with the backcutter installed. It was very easy to handle the panel and my 2 hp router had no problems at all.

The bit cuts so smooth -...

Charles M from Blairsville, PA Posted November 2, 2009
The bit cuts so smooth - We are using Character Ash for our kitchen face frames & doors. We also purchased the Freud 5-pc raised panel door set. The bit cuts fit together like a glove. We fed the pieces through several times taking small swipes at a time until we achieve the cut needed to fit into the framing member.

The bit does a great job...

Guest from Spring Branch, TX Posted June 12, 2009
The bit does a great job of raising a panel. When using any router bit, be sure to creep up on it by taking small bites, especially in wood such as Hickory that splinters easily. Also be sure to use adequate hold down (featherboard) pressure to keep the edge of the panel flat against the router table.

Write Your Own Review

Only registered users can write reviews. Please, log in or register

Videos

  • Freud Quadra-Cut

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012
Feedback X