Receive Free Shipping Every Day on Orders of $35 or More. Click Here to Learn How!
Receive Free Shipping Every Day. Click Here to Learn How!
Bending Wood - Part I
posted on by

Nature hates straight lines, and as woodworkers we spend a huge amount of time and effort in making things straight. But curves can and should be a large part of your woodworking. There are several methods for forming wood into curves, and the next few blog posts will explore these techniques. We will be looking at simple force bending, kerf bending, lamination and steam bending.

wood bending form wood forced bending technique 1

The most basic method is to simply manually bend the wood and attach it to a solid piece to hold the shape. Banding the edge of a curved piece of ply is an excellent example. If the curve is not too tight, and the stick relatively thin, this is easy. It stands to reason that the tighter the curve to be edged, the thinner the stick needs to be to conform to the curve. Veneer can follow a very tight curve, while a 3/4 inch thick piece of oak cannot be flexed much at all. Typically, the part is held to the curve with glue only since piercing the wood with a nail or screw would tend to break it under the bending stress. A good rule of thumb is that if the part can be formed by hand, then a good glue joint should hold it perfectly well. Glue up the mating surfaces and clamp the parts together. To avoid gaps, start clamping from the center and work outward, or from one end to the other. This allows you to work gaps out as you go.

wood forced bending technique 2 wood forced bending technique 3

Kerf bending is the process of cutting a number of slots into a piece of material that allow it to bend. Essentially, by kerfing the part, you are making it thinner, so it can be flexed to follow a curve. While this method is not very strong, it does allow for easy forming of wide or tall parts.

bending walnut wood kerf cutting wood to bend

Nearly any saw can be used for kerfing. Here I used the table saw, but for very long parts, a radial arm saw is ideal. A circular saw or even a handsaw can do the job too. The trick is to cut most of the way through the material to allow it to bend, but not so much that it becomes too fragile. Keep the kerfs close together and regularly spaced so that the bend is smooth and regular with no flat spots. I have even seen small moldings that were hand kerfed with a fine saw used as trim on antique doors.

bending kerfed wood bent kerf cut plywood

Kerfing allows for bending all sorts of thicknesses of stock, and is especially useful for bending plywood. Note here how I kerfed just the areas that were going to be curved, leaving the flat areas to be attached conventionally.

Stair builders often use this technique for the large "bullnosed" bottom stair on a fancy staircase. Getting the right depth and spacing can be a bit tricky at first, so practice your technique with some scrap material before committing to kerfing your actual parts.

bent plywood form

If you do not want to go through the effort of kerfing your own stock, you can purchase kerfed panels that can be cut to size and wrapped around a form. This option is excellent for decorative columns and such. Rockler sells 1/4 inch thick Neatform sheets for this purpose, and large lumber suppliers typically have 4x8 sheets available of various pre-kerfed materials. Kerfed plywood or MDF faces can be painted or veneered to achieve the final look your project demands.

neatform bendable mdf neatform detail

Practice these bending techniques to get a feel for how they work and might fit into future projects. In the next blog, we will look at laminating thin sheets into permanent curves.

Part II

Part III

posted on November 4, 2011 by Ralph Bagnall
previous post next post

6 thoughts on “Bending Wood - Part I”

  • Pieter Vander Tuin
    Pieter Vander Tuin November 5, 2011 at 10:48 am

    I like this format; pictures, basic information and easy to understand.


  • Ralph Bagnall

    Thank you Pieter, nice to hear that you like the format. We broke the series up to provide clear information without overloading it. Watch for the next in the series.

    Ralph Bagnall

  • Ryan

    I havent thought of using this technique before. However, I am familiar with the lamination method.

  • John Imm

    I have heard that you can soak wood in water and vinegar mixture to loosen the bond of the wood and form it while wet and allowing it to dry in its new form. Is this possible?

  • martin carrillo

    I need to buy some solid wood BENDING MACHINES cheap or used


  • John Moore

    Is there a way to access Part II of the bending wood articles.

Leave a comment
Feedback X