A gazebo is a nice finishing touch to any backyard, providing a new vantage point from which to enjoy your gardens and a focal point when looking at your landscaping. Gazebos also provide shade from the sun and shelter from rain, giving you more hours to enjoy the outdoors. The only drawback — especially for gazebos in the classic octagonal style — is that they are complicated to build and expensive to buy.
My design eliminates the fancy joinery that’s usually associated with an octagonal roof and walls. Instead, I used hinges to join the walls and a patio umbrella for the roof. As a result, my gazebo is quite easy to build for around $200 (perhaps a little less), plus the cost of the umbrella. An added bonus: it’s relatively lightweight and portable. If you want to move this gazebo to a new location or take it down for the winter, it is not difficult to do.
The finished project breaks down to four hinged pairs of wall panels and eight trim boards. The wall sections join together with 12 wingnuts, and it takes less than 30 minutes to raise or take down the gazebo. Nevertheless, the structure is very stable, even under windy conditions. To be on the safe side, I used a heavy concrete umbrella base of about 90 pounds, and I fastened the umbrella’s ribs to the hooks on the sides with elastic line as shown in the plans and photos.
Framing the Walls
Building the walls is made easier because all eight sides have the same overall dimensions, and seven of them are identical. This means that for every part, you only need to measure once — and then transfer the marks to the other workpieces.
I used 5/4 stock for the posts (pieces 5) and the cross members (pieces 6). The arch panels (pieces 1) are cut from 3/4" exterior grade plywood. The remaining framing is from 2 x 2 lumber, which you can rip from 2 x 4s if you so choose.
Once you’re done with measuring and marking, cut all the parts to size. This saves time and makes creating uniform pieces a bit easier. I marked the 27-1⁄2" radius on the arched panels using the simple homemade compass. I then made the curved cuts with a jigsaw, but a band saw would work as well.
All the other cuts can be made with a handsaw and miterbox, a portable circular saw, or, for best results, a table saw. Whichever you choose, you will save yourself a lot of trouble if you make certain that they are all perfectly square cuts.
Assembly of the walls works best on a large worktable. Sawhorses, topped with a sheetstock panel such as plywood, work great. Just be sure to use a sheet that you have checked to make sure the factory-made corners are indeed square. Begin by screwing the blocks (pieces 4) to the rails (pieces 2).
Align one post with the edge of the work table, and then clamp the rails with the block assemblies (see the Drawings for details) in position relative to the posts and balusters (pieces 3). Screw the rails to the posts and then to the balusters. Then screw the outboard rails to the blocks and to the posts.
For measuring the cross members (pieces 6), it’s easiest to first draw centerlines. Then lay them under the assembled wall and mark the angles. They should, of course, be close to 45 degrees. Make the cuts and position them, one over the other, inside the square opening.
Mark the area where they overlap. Here, you’ll have to make notches in order to fashion the halflap joints. It’s easy to do this. Simply make a series of cuts halfway through each cross member.
Switch to a sharp wood chisel to carefully clear out the waste. I found that I could clean these joints out by hand (no tapping with a hammer). Please take care never to have the chisel pointed toward your hand or body. It can easily slip and cause a nasty gouge if you are not careful.
Install the rails (pieces 2) at the top of the subassemblies next. Then install the arch panels (pieces 1). Use a few 3/8"- thick strips of scrap wood to support the panels in a centered position during assembly.
The entrance wall is identical in size to the others, except there is no balustrade assembly.
Install the Hinges
Before you install the hardware, take time to paint the parts. I chose to prime the wood with a good quality white primer and then filled holes and seams with latex spackle and caulk. I followed with two coats of white exterior enamel. You can choose any color that you wish — but that pure white enamel offered what I thought of as a classic look.
With the painting done, you can move on to installing the hinges. Divide the wall panels into pairs and use 8" strap hinges (pieces 8) to join each pair of panels together. The only exception to this is for the pairing of the entrance panel and its adjacent wall panel. Here, use T-hinges (pieces 10) instead of strap hinges as shown in the Drawings. You will need to bore one hole in each of the 6" strap hinges (pieces 9).
Install three of these hinges on the inside of one post for each pair of panels.
You’ll use these extra holes you’ve just drilled in the hinges to join each pair of wall panels to one another with bolts and wingnuts. (You’ll also need to bore a hole in two of the T-hinges in the same manner as you just did for the 6" strap hinges, for the same reason — joining the entrance panel to a paired panel set.) Now drill a pilot hole into the edge of the same rails you attached the hinges to, to install a screw hook (pieces 11) for securing the elastic cords later. Position these screw hooks 10" down from the top end of the rails. Twist the hooks into place.
Erect the Gazebo Walls
Stand the wall panels on the gazebo site of your choice. Arrange them so the entrance wall faces in the direction you prefer and so you have a perfect octagon. A simple trick to ensure “octagon-ness” is to make sure the distance between opposite corners around the octagon’s perimeter is equal. Once you have it right, clamp the still-loose hinge leaves to their mating posts. Bore holes through the posts at the holes you previously drilled in the hinges. Tap carriage bolts through each pair of hinges and post holes (from the outside face in), and secure the connection with washers and wingnuts.
Raise the Roof
Installing the umbrella (piece 13) is simple. Place the umbrella base (piece 14), as well as the table you want to use, at the center of the gazebo. Lift the top half of the umbrella clear of the walls, open it, and secure it to the lower umbrella post.
Tie off eight loops of elastic cord (pieces 12), one per umbrella rib, and hook them onto the previously installed screw hooks. Now you can proceed with installing the eight vertical trim boards (pieces 7), once again using carriage bolts, washers and wingnuts.
By the way, it pays to buy a patio umbrella of good quality. The gazebo will last many years, and you’ll want an umbrella that will, too. I chose a 10-foot diameter, wood model with eight sides, making the gazebo big enough for four to six chairs and a small table.
The distance from inside wall to inside wall is about 9-1⁄2 feet. You can opt for an 11-foot umbrella—and a bigger gazebo—but you will have to increase the width of the wall panels accordingly.
Here’s a note of caution: just because an umbrella has a listed diameter of 10 feet does not mean it will actually be that size. Sometimes the manufacturer uses round numbers, or measures over the peak of the umbrella. If you buy your umbrella first, you can always adjust your panels to suit.
This project is a nice summer effort that doesn’t take weeks to complete. It can help you enjoy your backyard and your woodworking hobby too.