Building a Stained Wood Dresser Valet Box with Brass Inlays
posted on February 1, 2008 by Bruce Kieffer
Brass inlayed stained dresser valet boxes This project shows off some simple, but highly effective visual enhancements like alternating stain and brass inlays.

One day, I just got plain old tired of all the clutter on my dresser, so I designed this sweet little wood dresser valet box. The “show” faces of the box are cut abutting each other from one blank of 1/2"-thick ash, and the adjoining corners are mitered.

For the dresser valet box diagrams and materials lists in PDF format, click here.

This makes the valet box appear to have continuous grain. Take a look at the ash blank layout and it should become clear how it’s done. I couldn’t find a piece of ash wide enough for my blank, so I glued it up from well-matched boards and hid the glue joints under the brass inlay grooves.

Avoiding Potential Pitfalls

Cutting with a small parts mitering jig on the table saw Use a small parts mitering jig and an 80-tooth cutoff blade to make the final cuts on the 45° mitered ends and beveled edges on the box.

In the grand scheme of things, this valet is not that hard to build, but it does takes time and patience to get it to all fit together precisely. Here are a few pitfalls I discovered along the way, so you can avoid them:

Cutting the mitered and beveled edges accurately and safely presents a problem. I built a small parts mitering jig to solve this (shown in the photo at left). It’s basically a table saw jig guided by a miter bar. T-tracks, hold-downs and stops secure and position the parts for cutting.

Marking out cuts on the valet box lid Mark out and cut the valet's lid, front and ends from one blank, then hide the edge-glued joints with the cut out inlay grooves.

The lid hinge is another issue. Being set into beveled edges of 1/2"-thick stock means the screws have very little wood to bite. The hinge mounting screws must be shortened to 1/4" long to avoid penetrating through the outside of the box. Although a 1-1⁄2"-wide piano hinge is rather large for a small box like this, its screw-mounting holes are farther from the hinge barrel than on narrower piano hinges, and because of this benefit, it ended up being the best option.

Hand sanding wood grain for a valet box Start setting up the finish by sanding down the grain, if you're getting swirl marks from an orbital sander, brush them off with a final hand sanding.

The brass inlay was another quandary to tackle. It’s designed to be pressure-fit into 1/8"-wide x 1/32"-deep grooves. On a larger project, you could hammer it into the grooves. But on a small piece like this, it would be too easy to break the joints by “banging” on the box. I routed the inlay grooves a smidgen wider so I could press the inlays in by hand with minimal pressure, and I glued them down with cyanoacrylate (CA) adhesive.

Many Samples Ensure Staining Success

Trimming painter's tape with hobby knife for staining Mask off the areas for the lighter stain so the dark stain doesn't bleed in, then trim off any excess with a hobby knife.

This valet is a good opportunity to hone your finishing skills. As a peer of mine once said, “I spend a hundred hours building a fine piece, then in less than one hour I mess it up applying finish.” This does not need to be the case if you do your homework first. The key to success is to make test samples, more samples and even more samples. Know exactly what finish and stain you’re going to use, and how you’ll apply it, beforehand. Using your project as a testing ground is a huge mistake — but one we’ve all made.

Testing board for different stains Testing out your stains on a piece of scrap will allow you to get a good idea of how your project will look without experimenting with finishes on your project.

Here’s how I approached staining and finishing the valet: I had pretty much decided on a maple color stain for the light areas, but I vacillated on the darker complementing stain. I picked an early American color and a red mahogany to test. I started by making an ash sample board, which I orbital-sanded to 220-grit. I divided the length in thirds and applied the three stain colors. I let them dry 24 hours, divided the width in thirds, and applied three sample finishes (satin wipe-on poly, gloss wipe-on poly and gloss spray-on lacquer). The results showed that my maple color stain was a good choice, the early American color stain was not the color I wanted for the dark areas, the red mahogany color stain was good but too light, and the finishes were all fine.

Brushing dark stain on valet box Use a high quality natural bristle brush, like this 1" badger brush, to spread the dark stain over your project.

I noticed sanding swirl marks in the darker stains (which is typical), so I knew I needed to straight-line hand sand prior to staining. I also know from experience that straight-line hand sanding produces darker staining results because it opens the grain more than orbital sanding with fine grits, and coarser grit hand sanding will make even darker results. I made more samples.

Wiping dark stain using a lint-free cloth Use a soft, lint-free cloth to wipe the stain with the grain, making several light strokes to evenly bleed the difficult light stain.

This time, I orbital sanded to 220-grit, hand sanded with 150-grit and then 180-grit. I applied two coats of the red mahogany color stain, applied the lacquer, and that gave me the results I wanted. I made another sample to be sure the maple color stain would still be good for the light areas, and it proved to be spot on.

Applying light colored stain to valet box Once the dark stain is dry, apply the lighter color, it will take around 24 hours, mask the dark area before starting.

Even though all the finishes looked good, I decided to use the spray-on lacquer for a few reasons. It was very easy to apply, and it would be easy to get it into the nooks and crannies of the small valet. It dried relatively fast, had a nice build and sheen and was easy to sand and recoat. I feared wiping on a finish could drag some of the dark stain onto the light stain and mess up my hard work.

Applying the Stain and Finish

Setting brass inlay strips into valet box Set the brass inlay strips into the shallow grooves of the box, the grooves should be a little wider than 1/8", so

Follow the staining and finishing steps in the photos. Be very careful when you apply the stain so as not to smear it on the inside of the valet, which is intentionally left unstained. Also be very careful when sanding between the coats of finish. It’s surprisingly easy to sand through the finish and remove the stain, especially on edges. With dark stains, this really glares out.

Spray-on lacquer finish on valet box A solid choice for finishing this project is a spray-on lacquer, make sure you spray in a well ventilated area, and, unlike the author, wear a vapor respirator.

To avoid this problem, apply two light coats of finish without sanding between them. Use 320-grit sandpaper to gently remove any nibs in the second coat of finish. Then use an ultra-fine 3M Scotch-Brite® pad (or #0000 steel wool) to smooth the finish. Remove all dust, and then apply a third and final coat of lacquer. You’ll end up with a fine project!

posted on February 1, 2008 by Bruce Kieffer
previous post next post
Leave a comment

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012
Feedback X