Fence Systems for Accurate Table Saw Ripping
posted on April 30, 2013 by Rockler

Ripping wood is a primary function of the table saw, and because its importance, many manufacturers pay particular attention to the quality the rip fence on the saws they offer. Still, many factory fence systems lack the reliability and precision that would qualify them for exacting work. In this article, we'll look at the basic requirements for good table saw ripping, and how an after-market fence system, like the Vega Fence System, can improve the ripping performance of a saw that's suffering from "fence problems."

Is Your Rip Fence Up to Par?

What makes a good rip fence? One of the most important factors is whether the fence offers reliable parallel alignment with the blade. When you lock a rip fence in position, it should be automatically drawn into near-perfect parallel alignment with the saw's blade, and this should happen unfailingly you shouldn't have to make frequent adjustments to the fence, or meddle with it to get it aligned. This is a very important point - accurate ripping, a clean cut, and even your safety depend on this alignment.

Checking for Parallel Alignment

Checking the parallel alignment of you table saw's rip fence is the first step in evaluating your saw's rip fence. But to check the alignment of the rip fence, you first need some information about the alignment of the blade in relation to the table saw's miter slot. For accurate ripping and crosscutting on a table saw, the blade must be in parallel alignment with both the miter slot and the fence. Since the miter slot cannot be "adjusted," the first step in the alignment process is to bring the table saw blade into alignment with the miter slot.

Aligning the Table Saw Blade

The procedure for aligning the table saw blade with the miter slot varies from saw to saw. The owner's manual for your saw is the best source of information for making this adjustment. In brief, the procedure for aligning the blade with the miter slot goes as follows:

Mount a blade in the saw and raise it to its highest position. Lay a straight edge on the surface of the table so that it is centered across the diameter of the blade and tight up against the blade plate (make sure that the straightedge is in contact with the blade plate itself, and not resting on the blade's carbide teeth). Next, measure the distance from the straightedge to the miter slot milled in the surface of the table at each end of the straightedge. If the measurements do not agree, the blade is out of alignment.

table saw alignment gauge


For the most accurate table saw adjustments, consider a precision alignment tool. A Table Saw Gauge reconfigures in seconds to test table saw alignment, arbor shaft runout, blade and flange runout, and rip fence alignment and straightness

Follow the manufacturer's instructions for adjusting the blade alignment. In most cases this will involve loosing three of the four bolts that attach the trunnions to the saw, tapping the assembly into the correct position and retightening the bolts (be sure to check the alignment again when you are finished to make sure that the act of tightening the bolts didn't pull the blade out of alignment).

Checking for Parallel Fence Alignment

Now you are ready to check the alignment of the fence. Since the blade is now in parallel alignment with the miter slot, you could simply check the alignment of the fence against the miter slot, but a more accurate reading is supplied by setting the fence in a few positions at varying distances from the blade and using the straightedge again to check the alignment of the surface of the fence and the surface of the blade. The measurements of the distance from the surface of the fence at the front end of the fence and the back end of the fence to the straightedge should agree. If they don't, the fence is out of alignment and should be adjusted.

Most fences have a provision for adjusting parallel alignment - again, the manufacturer is the best source of information on the procedure. If the fence cannot be accurately adjusted, or if the degree of disagreement between alignment measurements varies as the fence is positioned and repositioned, there is a strong possibility that your current fence is incapable of providing reliable parallel alignment. If you are generally satisfied with your saw's other qualities, correcting the problems with the fence is worth considering.

Other Rip Fence Considerations

Along with providing reliable parallel alignment, a good fence is also easy to accurately position at the desired distance form the blade. The positioning scale on the front fence rail should be easy to read, and the fence should have a cursor that can be accurately calibrated to produce precise settings. A useful fence also needs to have a wide enough capacity to do the work you need it to do. If the fence on your saw falls short of either of these additional criteria, and a new saw that comes with a better fence isn't in the plan, an after-market fence system is the best solution.

After-Market Precision Rip Fences

Rockler Magnet Micro Adjuster


The Rockler Magnet Micro Adjuster is a great match for a good fence that only lacks a mechanism for fast accurate micro adjustments. This handy tool lets you quickly and easily make fence position adjustments in increments of .001" or less.

Precision after-market fence systems were developed as a solution to a deficient fence on an otherwise reliable table saw, and they can work wonders for ripping performance. The Vega Fence System is a reliable choice. The Vega Utility Fence can be fitted to most portable and contractor table saws, and will greatly enhance the ripping performance of either. The Vega fence comes in 50" and 28" ripping capacities - the 28" length is a great way to increase the accuracy of a job site saw without sacrificing portability. The Vega fence also comes with a useful micro adjustment mechanism, which means that you can dial in ultra-fine adjustments (in the thousandths of an inch range) for precision rips or for setting up dadoes and rabbets.

The Vega system equals the stock fence on many high end table saws in quality of materials and manufacture. The Vega system's front fence rail is made from precision rolled plating quality tube, which is chromed and polished smooth and has extra thick walls for superior rigidity. The Vega fence head is extruded from high strength aluminum and is machined to closely match the contour of the miter bar. The rigid and precisely straight front fence rail and the precision matched fence head make for not only solid reliable positioning and alignment, but also an especially smooth movement of the fence from position to position.

vega fence systemThe Vega Fence is designed with easy installation on a wide variety of saws in mind and constitute a vast improvement over the fence offered on many less expensive home shop saws and both rival the best systems available for professional-class table saws. For a table saw that's generally sturdy and reliable, but suffers in the quality of its fence system it presents a logical and affordable route to safe, accurate and reliable ripping.

posted on April 30, 2013 by Rockler
previous post next post
Comments

5 thoughts on “Fence Systems for Accurate Table Saw Ripping”

  • William Simpson

    I have been looking for a rip fence and a miter gauge for a c.m.t 4" table saw via the internet.

    No Luck.

    Can you help me ?

    Thank you.

    William Simpson

  • John

    is the vega utility fence 50" be easily adapted to the ridged r4512 model?

  • Jerry Taylor

    We bought a small Pro-Tech Table saw Model #4106. We paid $40 for the saw with the floor stand.saw runs fine.

    The fence that the seller had is the wrong fence not for this saw.
    Do you have an inexpensive fence that will work on this saw? I see the company is out of business since 2006.

  • Arthur

    seeking suggestion for alternative replacement for Makita 2705 rip fence.
    Thank you.

  • Jess McKenzie

    What do you recommend as a replacement Rip Fence for the Grizzly G-1023?
    I also need to replace the G-1023 miter gauge.
    Bot lost on a recent move..

    Slots on this saw are about 0.75 inch.
    thanks....~jess

Leave a comment

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012
Feedback X