Incra Miter 5000 Sled  Zoom

Incra Miter 5000 Sled

Item #: 29773
$299.99
Each Oversold until 07/29/2014
Reserve Yours Today

Overview

The ultimate miter cutting workstation for the table saw!

  • Three-panel miter sled with patented Incra incremental angle control delivers perfect, repeatable accuracy.
  • Includes 36"-64" telescoping miter fence and dual flip stop.
  • With 364 precision indexed angle stops over +/-90° to produce perfect, gap-free miter joints on any multi-sided object.
  • Will crosscut a 25" W board with full control on a standard 10" table saw.
  • Steel GlideLOCK miter bar has 10 width adjustment points for zero side play and anti-friction travel.
  • Integral hold-down clamping system locks workpiece onto the sled for maxium accuracy and the cleanest cuts possible.
  • Renewable right panel provides zero-clearance tear-out control and cut-off support on both sides of the blade.
  • Two aluminum T-tracks are embedded in the MDF panel top to secure hold-down clamp and provide rigid support for the fence.

Tech Spec

Brand Incra
Manufacturer Part Number MITER 5000
Weight (lbs) 32.0000

Reviews

Customer Reviews

7 Review(s)

View All

Project time was cut by 2/3

Pat Posted June 26, 2014
I am not much of a jig maker so when I read so many positive things on the Incra 5000 I decided to give it a try on a project making outdoor furniture. When I have made these in the past for Church auctions it always took a long time to measure and make all the repetitive cuts going back in fourth from miter saw to table saw. It was quite a bit of work to get the self installed and adjusted but once I did I managed to do all the cuts on my SawStop in one afternoon instead of 3. Wow is all I can say. Wish I had purchased one a lot sooner.

I fully agree with the other...

Guest from Bedford, NH Posted November 21, 2008
I fully agree with the other 5-star reviews. Like the other Incra products I have purchased, the 5000 has great accuracy and many design elements that show that Incra is thinking through the practical issues that come up in the shop. If you are comparing this to a conventional sled, however, note that (1) the workpiece is not supported from the back on both sides of the blade and (2) a stop-block can be done only on the fence side of the blade. The 5000 is essentially a panel cutting sled that can miter or a miter with a zero-cutoff sled, depending on your point of view. Also note that the 5000 is shipped assembled for a right-tilt saw while the above photo of the product (at least right now) shows the miter remounted and fence converted for use with a left-tilt saw. Instructions for this change are included in the manual.

Initially, I was concerned about paying...

Larry S from Snow Hill, NC Posted June 15, 2008
Initially, I was concerned about paying this much money for a cut-off sled; but I needed to miter cut some melamine shelving board for a gumball display, and couldn't do it with just my table saw. This product is fantastic! It is worth much more, when you consider the resulting cut quality and angle adjustability that I needed, when making cuts on an octogon shaped display. I only wish that I had this many years ago. My motto is..."If you buy quality, you can make quality!"

Write Your Own Review

Only registered users can write reviews. Please, log in or register

Videos

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012
Feedback X