Rockler Large Trim for 2" Thick Doors Router Bit - 1" Dia x 2" H x 1/2" Shank  Zoom

Rockler Large Trim for 2" Thick Doors Router Bit - 1" Dia x 2" H x 1/2" Shank

Item #: 26841
$89.99
Each In Stock
Joint 1/16", 1/8", or 3/16" of material off of stock up to 2" thick—all with just two router passes!

Overview

If you need to trim a precise amount of wood off of doors and large panels, this kit will save you a lot of tedious setups and backaches. The kit uses a razor-sharp shear-cutting bit along with different bearing combinations to remove exactly 1/16", 1/8", or 3/16" of material in just two router passes-all without a straightedge! No need to strain your back lifting and balancing a large panel on top of a jointer. Instead, you bring the tool to the material. The kit includes one carbide router bit and five bearings to set up the various depths of cut. The bit can also be used as a double-bearing flush trim bit, as two bearings are included for that purpose. Capable of trimming stock up to 2" thick. Click the "Videos" tab to see how this kit will save you time!

A smaller version of the same kit is available separately (23105) for trimming stock up to 1" thick.

Large Bit Kit includes the following:

  • One 1" diameter bit with 2" long cutters and a 1/2" shank
  • Two 1" bearings for flush trimming
  • Three single bearings (7/8", 3/4", and 5/8" in diameter) for trimming 1/16", 1/8", and 3/16"



Tech Spec

Brand Rockler
Weight (lbs) 0.5700
Bit Type Flush Trim
Diameter 1"
Cutter Height 2"
Shank Size 1/2"
Flutes 2

What's included:

Large Trim Router Bit Kit, 1" Diameter x 2" Carbide Height, for up to 2" Thick Material
(1) Flush Trim Bit with Top-Mounted Bearing
(4) Interchangeable Bottom-Mounted Bearings
(1) Hex Wrench

Reviews

Customer Reviews

5 Review(s)

View All

I really like this bit. The...

Roy P from San Antonio, TX Posted August 4, 2011
I really like this bit. The cutting surfaces are even at an angle which helps mitigate problems with tearout. I bought it, not only on sale, but with free shipping as well. Once I got it and started using it I liked it so much that I went back to buy two more but the free shipping was suspended ... so I held off ... but if it hadn't been suspended I'd have bought two additional bits.

Bought both of these bits. Have...

James M from Mountain Lakes, NJ Posted September 12, 2010
Bought both of these bits. Have only tried the small one on plywood but I am very pleased with the resulting clean edge. The large bit is a monster. I am going to be using it to joint edges on longer stock using the factory edge of MDF as a guide.

I used this product to finish...

steve c from Orlando, FL Posted July 23, 2010
I used this product to finish routing the edges of my 1-1/2" thick butcher block kitchen counter top, after I had cut the initial shape out for the under mount sink with a jig saw. It worked really well and left a great finish.

Write Your Own Review

Only registered users can write reviews. Please, log in or register

Videos

  • Trim Router Bit Kits

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012
Feedback X