- Overview
- More Info
- Reviews
Perfect for doweling, mortising, pocket holes, hardware installation and more! Pre-sharpened bits are ready to use in any type of wood. Cut precision flat-bottom holes without tear-out.
- Presharpened bits are ready to use in any type of wood
- Cut precision flat bottomed holes with exceptionally smooth side walls
- No surface tear-out
- Durable, protective molded plastic index box
7-Piece Forstner Bit Set has 1/4", 3/8", 1/2", 5/8", 3/4", 7/8", 1" bits with 3/8" round shanks. Perfect for doweling, mortising, pocket holes, hardware installation and more! Use with a drill press or hand drill. Set comes in durable molded platic index box.
|
| |
Customer Reviews and Photos for:
7-Pc. Forstner Bit Set
|
Average Rating:
4.2
(25 customer reviews)
$31.49
Add your review...
|
|
|
1) Submitted by
Patrick, from Warrenton, VA
on 2/4/2011
Customer Rating:
For the price, it's a good steel Forstner bit starter set. The set arrived with sharp cutting edges. Be careful not to cut too fast to keep the edges from losing their temper.
|
|
2) Submitted by
Richard Riley, from Burgaw, NC
on 2/28/2010
Customer Rating:
Good assortment of popular size bits in a nice case. Easy to use!
|
|
3) Submitted by
C Tyner, from Trenton, TN
on 2/7/2009
Customer Rating: 
I am very happy with the set. Pretty good quality for the price. They do the job for me.
|
|
4) Submitted by
Ron Jacobsen, from Tallahassee, FL
on 11/25/2008
Customer Rating:
I am very happy with the set. It will do the jobs I need it to do. Granted it isn't the top of he line, but for what it is it does the job. Service from Rockler was as it usually is GREAT!
|
|
5) Submitted by
Walter Dobrowolski, from Oceanside, CA
on 11/23/2008
Customer Rating:
Good quality product! The price was exceptional as well!
|
|
6) Submitted by
Tom Silkett, from Maple Valley, WA
on 11/23/2008
Customer Rating:
Not the highest quality product but is suitable for periodic use. Good price for the set.
|
|
7) Submitted by
Edward Clayton, from Des Plaines, IL
on 11/24/2008
Customer Rating:
Bought this set because of the sale price.
I have several sets of Forstner Bits, and have not found a good cheap way to sharpen them....so it is often toss 'em and grab a new one.
|
|
8) Submitted by
Billl, from El Paso, TX
on 11/25/2008
Customer Rating: 
What a bargin--thanks--I would have never been able to get them any other way.
|
|
9) Submitted by
Donnie Fraley, from Rising Star, TX
on 3/23/2010
Customer Rating:
Not for heavy full time use but for limited use these are certainly worth the money. No regrets.
|
|
10) Submitted by
Drew, from Marion, IN
on 11/15/2008
Customer Rating:
I got this product to do mortises and they worked excellent. They cut accurately and stay sharp through lots of use.
|
|
11) Submitted by
Tom, from Corinth , TX
on 11/8/2008
Customer Rating:
I am very happy with this set and was so glad to find it on sale thanks. As always Rockler provides great prompt service.
|
|
12) Submitted by
Seth Rossman, from Greencastle, IN
on 7/6/2008
Customer Rating:
It's excellent for what it is and what it costs for the set. In the world of all Forstners they would be a 3.5 to 4. I should have bought just a couple of carbides, but these are excellent for occasional-only needs. So far, just used them on poplar. I have some fine and ultra fine 1/2" ceramic polishing stones, so I think they'll work better when dressed to a high polish.
|
|
13) Submitted by
Tim Dennis, from Woodstock, GA
on 2/10/2008
Customer Rating:
Great set of bits. I got them on one of the web sales and they were an excellent deal, I'd been searching for a nice set of Forstner Bits.
|
|
14) Submitted by
James Osborne, from Lakeland, FL
on 1/16/2008
Customer Rating:
I found the bits performing as advertized, very smooth walls and does the job fine.
|
|
15) Submitted by
Ron
on 12/8/2007
Customer Rating:
Used the forstner bits to make star candle box's and they performed well for me.
|
|
16) Submitted by
Rick Raley, from Hudson, WI
on 11/16/2007
Customer Rating:
I am building a CNC Router and I purchased the 40mm forstner bit to make pockets for bearing end caps.. Worked very well and is extremely sharp.
|
|
17) Submitted by
Steve Hughes, from Rincon, GA
on 10/12/2007
Customer Rating:
A great price for a starter set of Forstner bits. Nice clean sided cutting with zero tearout and fairly cool after boring 2" redwood. Keep the drill speed low.
|
|
18) Submitted by
Monte Miller, from Denton, TX
on 1/8/2007
A well-made set of bits suitable for the fairly serious woodworker. Nicely machined and gives consistent results. Good value.
|
|
19) Submitted by
Jeff, from Costa Mesa, CA
on 9/7/2006
Great set for the money. It's sharp and cuts clean.
|
|
20) Submitted by
Mike Blanche, from Cedar Hill, TX
on 11/21/2009
Customer Rating:
I bought this set to get a 3/8 inch bit, crucial to guitar construction if you're going to install Tune-o-matic or Gotoh parts. I couldn't find a single 3/8 anywhere else.
|
|
21) Submitted by
Harry & Harry , from Salt Lake City, UT
on 3/22/2010
Customer Rating:
Another great deal from the best in the business, Rockler. These forstner bits are quality steel, sharp, and you will find that they get the job done. They also arrive in a nice hard case. They are in very usable sizes. On sale or not, these bits are a quality product which does not suprise me coming from Rockler. Thanks again to everyone.
|
|
22) Submitted by
Bob Groh, from Blue Springs, MO
on 8/25/2011
Customer Rating:
Couple of points first - I am not a terribly experienced woodworker and Forstner bits are definitely new to me. I do have a Freud 1-3/4" Forstner bit as a 'standard of comparison. I purchased this set on sale because I wanted to have an assortment of smaller bits for use as needed. These seem to be decent bits but I only gave them 3 stars since I had to leave room in the rating for really good bits. When I got the set, I took each one out, looked it over carefully and then bored a series of test holes using a 3/8" variable speed drill in pine and fir plywood and compared the results with the Freud. My general observations: they are nice and shiny but the cutting edges are not totally sharp visually they have flat spots and have a bit of a burr. They seemed to cut ok and the chips cleared out ok but I had to press pretty hard after 4 or 5 partial holes the bits felt very hot to painful level. The bits ran true with no wobble that I could see. Overlapped holes looked good. From my observations, this is a pretty good inexpensive set. You should certainly watch the bit temperature and you should definitely buy a sharpening kit as you are going to want to sharpen them.
|
|
23) Submitted by
Steve Eikenberry, from Fort Wayne, IN
on 12/19/2011
Customer Rating:
For the money these bits are a good deal, especially on sale. They don't measure up to carbide bits but for the occasional user they should be fine. They don't come razor sharp so having the ability to file them sharper would be a plus. I've used them on poplar, birch, and oak without issues...good clean holes with clean sides and bottoms. They come packaged in a durable plastic case for dust free storage. The one confusing part is each bit is stamped with it's max RPM rating. The bits are stamped from 620 RPM to 870 RPM depending on the bit size...which makes sense for Forstner bits. However, the inside lid of the custom storage box has a label stating various RPM's recommended for different bit sizes...the problem is the label offers RPM's up to 2000! Why would package bits clearly meant for low RPM's have a label suggesting 2000 RPM's? The novice woodworker would burn up their bits in a hurry using high RPM's. Forstner bits are best used at the lowest RPM possible to achieve good results. That's my only issue with this set.
|
|
24) Submitted by
Richard Guess, from Menifee Valley, CA
on 12/23/2011
Customer Rating: 
I've always bought just what I needed, but I saw a chance to get a set, so I bought this 7 pc set. Although I didn't know what to expect, I have to say I'm slightly disappointed. I've only used the 3/8" bit, I found it not very sharp. From the very first hole, I felt, I needed to apply way too much force. The holes come out nice and smooth, with no rough edges, but these won't last long before they need sharpening. I don't know if they can eve be re sharpened. I think I'll return them on my next visit , and maybe just buy the 3/8" & 1/2".
|
|
25) Submitted by
Kurt, from Louisville, KY
on 4/9/2008
Customer Rating:
I bought both the 7 piece and 6 piece fractional Forstner bit sets on sale. A few of the bigger bits had some nicks and burrs in the machined surfaces. The smaller bits were perfect. All the bits cut through dry oak with easy. These aren’t the highest quality bits money can buy, but they’re good for the price, and a bargain on sale. I would recommend them.
|
Home  Hand Tools and Shop Accessories Drilling Drill Bits Forstner Bits 7-Pc. Forstner Bit Set 
|
(0 Items)
