Customer Reviews and Photos for:
4'' Solid Brass Caliper
|
Average Rating:
1.6
(15 customer reviews)
$8.99
Add your review...
|
|
|
1) Submitted by
Charles Davis, from Summerville, SC
on 12/30/2007
Customer Rating: 
I was looking for a good, small and cheap caliper that would fit into my shirt pocket when working on projects. Rockler's 4" brass caliper fit the bill. If I want really accurate measurements, I go get my electronic calipers, but this one is just plain handy and a time saver.
|
|
2) Submitted by
John, from Effingham, IL
on 9/13/2007
Customer Rating:
Nice little 4' brass caliper.
|
|
3) Submitted by
Bruce Moore, from Nacogdoches, TX
on 4/11/2008
Customer Rating: 
The caliper was bent when I received it. I tried to straighten it and in the process it broke.
Editor's note: Our customer support at 800-279-4441 will be able to arrange a replacement.
|
|
4) Submitted by
Joe M., from Alexandria, VA
on 4/4/2008
Customer Rating:
Spend a few more bucks an get something worthwhile.
|
|
5) Submitted by
Kevin Minson, from Romeoville, IL
on 3/13/2008
Customer Rating: 
The caliper was bent when I received it and the markings are very difficult to see. I don't have another one so this will have to work for now.
|
|
6) Submitted by
Chuck, from Ingleside, IL
on 10/16/2007
Customer Rating:
It was a little bent when I got it (I straightened it) and the zero markings don't precisely match up but it'll probably come in handy. I wouldn't recommend it, but I still like Rockler. They're a good company.
|
|
7) Submitted by
William Mayer, from New Lenox, IL
on 12/30/2007
Customer Rating:
The calibration numbers do not correspond to known wood thickness , used to verify the tools accuracy. I am not satisfied with this tool and would not recommend to anyone I am aquainted with to purchase this tool. This will not deter me from buying any tools in the future from Rockler.
|
|
8) Submitted by
Tony Joyce from NC
on 12/13/2009
Customer Rating:
I didn't expect much, but I did expect to be able to read the marks and numbers. Not worth the effort.
|
|
9) Submitted by
Gary, from Bowling Green, KY
on 1/7/2008
Customer Rating:
I bought about 10 of these for our shop and wished I hadn't. They fall apart, are not accurate and are not very easy to use. Save your money and buy a good quality one.
|
|
10) Submitted by
Eddie, from Ware, MA
on 12/30/2007
Customer Rating:
This is the worst caliper Ihave ever seen. It was bent and when you pulled it out a ways the channel was way to wide in the front, so it just flopped there. You would have a real hard time measuring anything with this piece. The rest of my order was fine,the service was great.
|
|
11) Submitted by
Stephen F., from Slidell, LA
on 12/13/2009
Customer Rating:
No where near accurate. I would say almost a full 1/16 off. If postage would not cost as much as the product I would return it for a refund.
|
|
12) Submitted by
Carl Kemp, from Mandeville, LA
on 1/4/2010
Customer Rating:
Poor Quality, shoddy machine work. Caliper would not close or zero (1.5 mm off). Bent , would not slide smoothly. Would not recommend.
|
|
13) Submitted by
Paul , from Harrisburg, PA
on 2/5/2010
Customer Rating:
Made in China. Mine doesn't even read a correct zero measurment when it's closed. The rest of the markings are no better. Don't waste your money!
|
|
14) Submitted by
Dean Wolfe, from Manchester, CA
on 4/19/2013
Customer Rating:
I purchased this small caliper to replace a lost one that I had for 30 years. I use a small caliper to size drills to screws etc. This caliper is poorly made of crude construction and does not meet my needs. Basically it is a piece of junk that I was surprised. It is a shame because a small inexpensive caliper has many uses around the shop. I am returning it today if the postage is reasonable, if not, I will dispose of it.
|
|
15) Submitted by
Gatis, from Pine Springs, MN
on 1/23/2013
Customer Rating:
It was bent. Calibration off by 1/8th inch. Rockler did accept my return.
|
Hand Tools and Shop Accessories 
(0 Items)
