Customer Reviews and Photos for:
Plastic T-Molding Edging
|
Average Rating:
4.5
(23 customer reviews)
$17.19
Add your review...
|
|
|
1) Submitted by
Jerry from TN
on 7/12/2011
Customer Rating: 
I had someone to do the routing for me on some table tops, but I ended up putting on the edging. Easy! I didn't even have to use a rubber hammer. I basically rolled the top onto the edging. Great look.
|
|
2) Submitted by
DIANA, from Manhasset, NY
on 11/29/2009
Customer Rating:
We bought it to replace some molding on the kitchen cabinet on our boat. Worked well, looks great! An inexpensive upgrade that made a nice difference.
|
|
3) Submitted by
Ken Hamilton, from Ashburnham, MA
on 9/19/2009
Customer Rating: 
re. the #38767 slot cutter. It has a 1/2" shaft. Didn't list it and didn't fit my router. Had to borrow another router. Also, don't move router out of slot until spun down. I did when I had to reposition work and it took a small chunk out of table top (rookie mistake).
|
|
4) Submitted by
Ken Hamilton, from Ashburnham, MA
on 9/19/2009
Customer Rating:
Used this edging on a replacement table top for a Coleman camper. Original table had similar edging that was getting beat up and moisture getting to particle board. Edging adds nice finish and easy to install (after using slot cutter). Taping with a plastic-head hammer stuck the edging in nice & tight. Will be ordering more for other projects.
|
|
5) Submitted by
Vaughn Martens, from Racine, WI
on 9/4/2009
Customer Rating:
I'm using the T-molding to finish the edges of the plywood sides on the Pinewood Derby track I'm refinishing. The molding applied very easily and securely using the recommended slot cutter. Shipping was very quick.
|
|
6) Submitted by
Annie Buma, from Seiad Valley, CA
on 7/3/2009
Customer Rating:
I used this product with great sucess to make a table for my 90 year old mother. she was falling asleep and hitting her head on the table. The edging, applied using recommended slot cutter made a soft edge for the table.
|
|
7) Submitted by
David Kirkpatrick, from Straughn, IN
on 4/27/2009
Customer Rating:
Worked very well for the project I completed. Covered the exposed edges of 3/4" melamine particle board for display cases. Would buy this product again.
|
|
8) Submitted by
Dave B, from White Plains, NY
on 11/26/2008
Customer Rating:
Used the t-mold to edge a 3/4" thick 8 foot diameter table to. Worked like a charm.
|
|
9) Submitted by
M L Witherell, from Heuvelton, NY
on 9/29/2008
Customer Rating:
The t-molding was used to repair our favorite dresser. The old molding had crumbled in several areas. We are delighted with the finished look of our "new" looking dresser. It took a lot of research to find the t-molding as I did not know the name of the item I was looking for. The color was a perfect match.
|
|
10) Submitted by
Don Richardson, from Versailles, KY
on 9/23/2008
Customer Rating:
I was doing some rework and refinishing on an old (about 100yrs old)cedar chest. There were three places where the boards had separated about 1/16 of an inch. I didn't want any small critters (spiders, etc.)possibly getting in the chest. I purchased the T-molding, cut it to length and installed it in the cracks between the boards on the inside of the chest. It worked perfectly.
|
|
11) Submitted by
Steve Jones, from Lakeland, FL
on 8/13/2008
Customer Rating:
I have ordered this molding 3 times. The first time it was much thicker and when I got the second batch it seemed flimsy and I wasn't too happy. Now that I have used about 150 feet of the stuff, I actually appreciate that it is thinner and easier to manage. I make a lot of Lazy Susans for family and friends and this stuff is great. If you use good 17/32 plywood and offset the groove a bit, you get the perfect lip that keeps things from sliding off as it is turned.
|
|
12) Submitted by
Gary Iverson, from Nampa, ID
on 1/3/2012
Customer Rating: 
I bought two rolls of the 3/4" T-Molding 100' each. The product is a good quality and the colors are nice. The only problem with the 3/4" is that the insert barbed portion is not well done: it is quite shallow does not go deep enough, and the barbs are very narrow, so it does NOT hold well at all in any normal slot on MDF or plywood. It does okoay on a flat non-curved surface, anything else it slowly slips out. If they can make this a bit more agressive on the barbed portion, and make it deep enough to really hold well once in place, this will be an excellent product!
|
|
13) Submitted by
John King, from Greensboro, NC
on 12/29/2008
Customer Rating:
When I first received this molding I was very disappointed in it. It was very lightweight and seemed flimsy. However, once I inserted it into the slot it seemed adequate and should do the job.
|
|
14) Submitted by
Landis Custom Cabinets, from Red Lion, PA
on 8/4/2008
Customer Rating:
I used the 13/16" T-Molding to finish off the edge of a custom top I made for a customers "AV" cart. The top was 3/4" particle board with a Formica laminate applied. I gave the edges a 3" radius which was sufficient to bend the moulding around the corners with sufficient ease.
|
|
15) Submitted by
Charles Anderson, from Litchfield, MN
on 7/13/2008
Customer Rating:
This T-Molding provides an excellent edging for a melamine cabinet. The 3/4" width mounts flush on both top and bottom surfaces. It provides an excellent way to finish the exposed edges of melamine.
Storage Cabinet for Craft Room
|
|
16) Submitted by
Brian Goodknight, from Otisco, IN
on 1/24/2008
Customer Rating:
The edge banding made this hardworking play table safe for the little ones. I also used product 78477 Shaker pegs for the drawer and 58400 Brass ball catches to secure the drawer. The center square comes out, flips over, for use with a block grid for popular interlocking blocks. The edge banding is what made it both safe and functional.
Used the edge banding on product 63453 baltic Birch for the top. Legs and drawer are of maple.
|
|
17) Submitted by
TR, from Pampa, TX
on 1/22/2008
Customer Rating:
We recently bought a salvaged travel trailer. We are in the process of refurbishing it. It didn't come with a table for the dining area so we're in the process of making one. We needed some molding to go around the edge to finish it. This t-molding is perfect and so easy to install.
|
|
18) Submitted by
Teresa , from Round Rock, TX
on 1/15/2008
Customer Rating:
I'm restoring an old travel trailer. The fold down table was in good shape with the exception of the molding around the edge. This was the perfect replacement.
|
|
19) Submitted by
Lennie Schoonover, from Bonney Lake, WA
on 11/28/2007
Customer Rating:
We are refitting an older sailboat that had this style trim on its countertop. This T-moulding is just the thing to replace the old brittle or shrunk-up stuff from 30 years ago.
|
|
20) Submitted by
Bobby West, from Alamogordo, NM
on 11/19/2007
Customer Rating:
My wife was using an old fold up table as an extension for her sewing cabinet. The particle board finally gave up and it collapsed. I put a new plywood top on, but it looked awful plus it was snagging the fabric. Using the T-mold from Rockler and some laminate dressed it right up. Her fabric slides acrossed it smoothly with no catching or snags. Now my wife is happy! Thanks Rockler.
|
|
21) Submitted by
Joe, from Stevens Point, WI
on 10/25/2007
Customer Rating:
The molding was just what I needed to finish the edges of the desk. The price was reasonalble and the shipping time was excellent. Excellent company to order from.
|
|
22) Submitted by
Luisa Wang, from Houston, TEXAS
on 11/3/2011
Customer Rating:
Is very hard to match only with 4 available colors with plastic laminate cabinets. Grey color will be great. I have not found any other company that offer other colors.
|
|
23) Submitted by
Mark Ensminger, from Mashpee, MA
on 4/5/2008
Customer Rating:
Make sure you buy the right size. This product is easy to install. Make sure your kerf cut is centered by running test cuts on scrap stock. The roll of white t-molding I received had several scuff marks. These were easily removed with 320 grit sandpaper. Another great Rockler product.
|
Wood Products 
(1)
