Customer Reviews and Photos for:
Twin Pin Sewing Machine Hinges
|
Average Rating:
2.9
(12 customer reviews)
Add your review...
|
|
|
1) Submitted by
Jr Wood Chuck, from Sweetser, IN
on 10/17/2009
Customer Rating: 
I found these hinges to be well constructed. Nice heavy hinges for the job. No reworking needed to make them fit in the mortise.
|
|
2) Submitted by
Peggy, from Gulf Breeze, FL
on 6/10/2008
Customer Rating: 
Fit our needs perfectly and are very nice quality. Very few sites carry these types of hinges, but this company's had very exacting measurements available on line, they came in pairs, and included screws --very unusual! Processing and shipping my order was very timely. Rockler was very easy to contact by phone and talk to a knowledgable person.
|
|
3) Submitted by
Ron Russman, from Taylorsville, KY
on 5/11/2010
Customer Rating:
This is a hard to find hinge. Works perfectly and just as shown. I would like to see a template available for it because I use these a lot. Made my own so not a big deal.
|
|
4) Submitted by
Randall Brookhiser, from Ottumwa, IA
on 1/21/2008
Customer Rating:
Perfect part for the application. []
|
|
5) Submitted by
Nicholas J Schulz, from Willmar, MN
on 2/19/2009
Customer Rating: 
Good hinges, they will work but there is alot of side to side play in the hinge plus I had to file to get the hinge to open the 180.
|
|
6) Submitted by
John Van Dam, from Bronson, MI
on 6/22/2009
Customer Rating:
The hinges would not open and lie flat to 180 degrees. Other than that the hinges looked very nice. Filing needs to be done to get the hinges to open flat.
|
|
7) Submitted by
Greg Roesch, from Iowa City, IA
on 1/6/2011
Customer Rating: 
Three hinges broke when not under pressure and had to be replaced. They would also not lay flat without filing. Any savings was negated by poor quality and cost of replacement.
|
|
8) Submitted by
Susan Firor, from Moscow, ID
on 1/15/2012
Customer Rating:
Hinges are tight, perhaps too tight, but I prefer that to too loose. I had to file to get them to open to 180 degrees. And the finish was pretty bad. They arrived scuffed up and not very attractive. My application has them mostly hidden, so I used them. But next time I'll likely look for a higher-quality hinge.
|
|
9) Submitted by
Charles Hampton, from Las Vegas, NV
on 2/22/2011
Customer Rating:
I found the set to be of poor quilty an poor woormanship.
|
|
10) Submitted by
Mike Graning, from Jericho, VT
on 7/15/2011
Customer Rating:
Hinge wouldn't open to 180 degrees, and broke when under load.
|
|
11) Submitted by
Larry Hartley, from Heber, UT
on 5/15/2012
Customer Rating:
Hinges work well but the screws were not included. When I tried to match screw size I found that a #6, were too small for good appearance. I found a #7 was a better fit but hard to find. I would suggest including the proper fitting screws with the hinge.
Editor's Note: Screws were to have been included with these hinges Larry. Our customer service team at 800-376-7856 will be able to assist.
|
|
12) Submitted by
Stephen, from Augusta, KS
on 11/3/2007
Customer Rating:
Nice thick hinges with a good finish. My only problem with them is they would not close a full 180 degrees. I had to take a file to the part that stops the hinge from laying flat.
|
Hardware 
(0 Items)