Customer Reviews and Photos for:
2'' T-Knob
|
Average Rating:
4.6
(32 customer reviews)
Add your review...
|
|
|
1) Submitted by
S Ferguson, from Mundelein, IL
on 3/20/2010
Customer Rating: 
Bought two 5 star knob with 1' stud 5/16' 18 tpi for a router dado jig. Tried to find locally but hardware had a knob and a bolt and told me to cut off the bolt. Rather than hand cutting the bolt would rather spend my time building jigs and woodworking so opted for buy. Work well.
|
|
2) Submitted by
KLH
on 9/11/2009
Customer Rating: 
Ordered 2 at different times, a week apart, products received where two different sizes, one had a long base and the other had a short base. Needless to say I couldn't use them as intended-on the same jig.
|
|
3) Submitted by
Doug Wise, from Smithfield, NC
on 6/29/2009
Customer Rating:
Great knobs for use on jigs and fixtures. I used the knobs on a mortising fixture I built. The plan called for studded knobs but the 1" length was too short. I ordered the through knobs and just used a carriage bolt to get the extra length. It would be nice if the stud knobs came in 1 1/2" or 2" lengths for mounting items through two 3/4" plywood thicknesses.
|
|
4) Submitted by
Bob, from Lavonia, GA
on 6/6/2009
Customer Rating:
Rockler always means quality and fast service. This hardware #23804 5-star knobs with through hole, 1/4' 20 tpi is no different. I recommend Rockler to everyone.
|
|
5) Submitted by
Steve Williams, from Denver, NC
on 5/17/2009
Customer Rating:
Right size at the right price. A quality item. I used two of them on a jig I made for routing exact size dados.
|
|
6) Submitted by
Rikkyj, from Inverness, FL
on 3/28/2009
Customer Rating:
Purchased three 5/16" "through" knobs. High quality, as expected. Used to add a fence to a drill press table.
|
|
7) Submitted by
Doug Schmid, from Carrington, ND
on 8/1/2009
Customer Rating: 
Didn't use this on a wood project but to replace a similar knob in a tractor cab to hold the windows open. They work great
|
|
8) Submitted by
Tim McAnnany, from Rockfield , KY
on 3/22/2009
Customer Rating:
I recently made panel press clamps and used the T-knobs to tighten down the clamps. They work great and holds the panels in place after gluing.
|
|
9) Submitted by
Jon Shackelford, from Chelsea, MI
on 3/14/2009
Customer Rating:
Good quality - smooth running.
|
|
10) Submitted by
David B, from Darien, CT
on 3/11/2009
Customer Rating:
I used these knobs to replace wing nuts on a jig I had made to make mortices with my router. What an improvement. Much easier on the hands. They work great for jigs. My local hardware store was charging nearly three times as much for identical knobs.
|
|
11) Submitted by
SeaWolf's Home Workshop Blog, from Jacksonville , FL
on 3/11/2009
Customer Rating:
Overall these are great knobs for jigs, tool mounts etc.
However the 5/16 "T" knobs have a lock nut embedded in them, so they do not turn easily unless you re-tap them.
It would also be nice if the 5/16" and 3/8" stud knobs came in 1 1/2" and 2" lengths for mounting items to work bench. 1" is not long enough to secure a 3/4" plywood base. A hex head hole in the through knobs would be nice to convert them into a stud knob with a standard bolt.
|
|
12) Submitted by
Carl, from Assonet, MA
on 1/9/2009
Customer Rating:
I replaced the nuts that held the skids on my snowblower with these "T" knobs. Now I can adjust the height of the snowblower without carrying a wrench
|
|
13) Submitted by
James Orzech, from Danielsville, PA
on 12/26/2008
Customer Rating:
Excellent knobs for making jigs and fixtures.
|
|
14) Submitted by
Brad Feuerhelm, from Presque Isle, ME
on 12/25/2008
Customer Rating:
These work great! I use them for attaching my planer, jointer, router table, and grinders to my bench using a piece of plywood attached to the tool then bolt down to bench using these knobs. All I have to do to switch between tools is loosen the knobs and slide the tool off the bench and slide the next one off. Works great for my very small shop. Thanks Rockler for carrying these, couldn't get them locally.
|
|
15) Submitted by
Bill, from Whitinsville, MA
on 12/3/2008
Customer Rating:
There are used on a variety of jigs and clamps. Easy on the old hands to tighten.
|
|
16) Submitted by
Richard Schipae, from Somerset, KY
on 11/1/2008
Customer Rating:
My wife got into rug hooking which requires various adjustable wood frames. The 5 star knobs are great for the clamping at the adjustment point. Rockler has some great products at very reasonable prices. A great internet source.
|
|
17) Submitted by
Steven M. Mahan, from Stockton, CA
on 9/5/2008
Customer Rating:
I used the star knobs for years to attach various parts of my robot. The photo shows four used to attach the head assembly. These knobs provide great strength with the added ability for quick release and attachment.
|
|
18) Submitted by
Dan Phalen, from Scappoose, OR
on 8/24/2008
Customer Rating:
These knobs attach the fence of my router project to the T-Tracks imbedded in the table top. I also used the T-slot bolts and 2" T knobs to build a featherboard attachment.
|
|
19) Submitted by
Bill Muno, from Evanston, IL
on 7/21/2008
Customer Rating:
2" T-Knob: Excellent quality at a reasonable price.
|
|
20) Submitted by
Leonard Stevens, from Oktaha, OK
on 6/9/2008
Customer Rating:
I purchase these items for jig making. These were very good and shipped promptly.
|
|
21) Submitted by
Barry D Thomas Sr, from Villas , NJ
on 5/11/2008
Customer Rating:
Purchased these knobs to hold the roller uprights for adjustments.
|
|
22) Submitted by
Jerry Gentry, from Seymour, INDIANA
on 2/29/2008
Customer Rating:
I am useing several different knobs in building my own router table and they are working great. Quality seem great and expect them to last forever. Shiping was quick and easy as expected.
|
|
23) Submitted by
Pat Monahan, from Downs, IL
on 2/26/2008
Customer Rating:
T-Knobs were used on a planer stand with extension rollers. The stand was shown in shopnotes.
|
|
24) Submitted by
Steve Mellott, from McDonough, GA
on 1/6/2008
Customer Rating:
I've used these knobs on various table saw jigs and they work well. A good value for the money.
|
|
25) Submitted by
Jon Simpson, from Cedar Falls,, IA
on 10/17/2007
Customer Rating:
I use these star knobs in the guitar-making jigs that I build. Primarily part of a clamping mechanism, they work great!
|
|
26) Submitted by
Robert Scroggs, from Odessa, TX
on 3/29/2010
Customer Rating:
I ordered 4 "through" knobs. They had a long base. It would be nice if the bases were shorter so the knobs would not stick out so much.
|
|
27) Submitted by
Hank Brunner, from Jamestown, ND
on 9/13/2007
Customer Rating:
I recently purchased the five star knob to repair my light stands (pro audio). Had to improvise with just the knobs since there was only a 1 inch stud on the knob bolts. I used red loctite on 5/16" threadrod and was able to make the studs as long as I wanted. They work like new.. Thanks
|
|
28) Submitted by
Rich Jensen, from Bothell, WA
on 2/10/2008
Customer Rating:
I received the items within 1 week. The order was correct, as I expected.
|
|
29) Submitted by
Scott Evans, from Portland, OR
on 1/23/2008
Customer Rating: 
On two knobs out of about ten that I've purchased from Rockler, I had to drill out some of the plastic inside the through-hole so that they would spin freely on the carriage bolts I was using. They have all worked very well in other respects.
|
|
30) Submitted by
Bill, from billsguitars.blogspot.com, CA
on 11/8/2008
Customer Rating:
These quality knobs and shafts are hard to find but invaluable in finding ways to attach jigs when making guitars.
|
|
31) Submitted by
William Heidelberg, from Piney Flats, TN
on 11/17/2008
Customer Rating:
Always satisfied with service and product I order from Rockler. Appreciate speedy shipment. Still a customer as long as things don't change...and I don't expect that to happen.
|
|
32) Submitted by
James J Luke, from Troy, NY
on 2/15/2008
Customer Rating:
Received items in 5 days and had no problems.
Items were excellent as expected.
|
Hand Tools and Shop Accessories 
(0 Items)
