Customer Reviews and Photos for:
Miter Slot Hardware Kit
|
Average Rating:
4.5
(26 customer reviews)
$7.99
Add your review...
|
|
|
1) Submitted by
Mike C., from Great Falls, VA
on 8/7/2011
Customer Rating: 
Excellent product and a very good buy - got it on sale.
|
|
2) Submitted by
Lynn Fifer, from Woodstock, ILLINOIS
on 8/6/2011
Customer Rating:
I easily adapted a digital indicator to the table saw miter slot for indicating the blade and fence. I use them on the table saws I have two and router tables I have four to hold feather boards. Great product, I have purchased before with feather boards.
|
|
3) Submitted by
DS Lunsford, from Westport, WASHINGTON
on 3/3/2011
Customer Rating:
These are very good for holding jigs
|
|
4) Submitted by
Kelly Craig, from Olympia, WA
on 5/19/2010
Customer Rating:
Had I had a few sets of these when I started woodworking decades ago, I may have learned the value of jigs much quicker. Subsequently, my woodworking capabilities would have been far more progressed.
Prior to using these, I found work-arounds, to avoid having to clap my jigs to the table saw, band saw or router table. With these, securing a jig is a snap. I no longer have to fight difficult clamps. Now, it’s just a quick turn of the knobs and the feather board, tunnel cutting jig and any other jig that must be stationary on the equipment is secure.
These work well in the tracks of my PowerMatic band saw, my Delta Unisaw and even on my Bosch site saw (the tracks are just a smidgen larger than the others).
|
|
5) Submitted by
Richard Branch, from Covina, CA
on 11/9/2009
Customer Rating:
A must have product. I use mine with the double featherboards.
|
|
6) Submitted by
Ron Ecke, from Erie, PA
on 6/18/2009
Customer Rating:
I ordered four of these kits as they work excellent for my self-made feather board jigs throughout my woodshop. Highly recommended for all standard miter slots! I've included a picture of the re-saw jig using just one of these kits, and it works great!
Re-Saw Jig using THIS Kit
|
|
7) Submitted by
Jerry Thompson, from Akron, OH
on 4/8/2009
Customer Rating:
Works Great don't know how I did without it.
|
|
8) Submitted by
Lyle Ogle
on 1/21/2009
Customer Rating: 
Does a good job I wish the bolt diameter was a touch smaller for some store bought jigs.
|
|
9) Submitted by
Gary A. Ledbetter, from Marysville, CA
on 1/20/2009
Customer Rating:
The kit is a great value and locks in place on the table saw miter slot, I use them for shop made work holders and feather boards.
|
|
10) Submitted by
Dan Perrin, from Pocono Piones, PA
on 12/31/2008
Customer Rating:
Great Pruduct. I used it to make a long featheboard and it fits both my router table and table saw (Both Bosch products)perfectly.
I plan to buy another set or two to make a cross cut sled for the table saw.
|
|
11) Submitted by
Ron Minutes, from Scranton, PA
on 9/21/2008
Customer Rating:
I purchased this kit with the 4 Piece Router Table Accessory Kit, to help match up my home made featherboards. This was the perfect end to my new router table.
|
|
12) Submitted by
Mark Chitwood, from Lawrenceville, GA
on 8/3/2008
Customer Rating:
Simple yet very usefull little tool. Seems well made and locks tight in all my miter slots.
|
|
13) Submitted by
Tom Cuccia, from Pearl River, LA
on 7/27/2008
Customer Rating:
It sure makes attaching my homemade feather boards and my router fence much easier.
|
|
14) Submitted by
Gary A. Lange, from Nixa, MO
on 7/27/2008
Customer Rating:
Just what I expected from a quality company.
|
|
15) Submitted by
Ivan Bulaich, from Watsonville, CA
on 7/6/2008
Customer Rating:
Some of the miter slot clamps I have used in the past and just recently were pretty much junk, they did not clamp to the slot at all, but this miter slot clamp really WORKS! It clamps into a standard miter slot with considerable force, excellent design.
|
|
16) Submitted by
D. Hammack, from Columbus, MS
on 5/18/2008
Customer Rating:
This is probably the tool that gives you the most utility for the least money. I used it on a homemade featherboard. For six bucks, it's great to have around for later when you need it.
|
|
17) Submitted by
L. Jones, from ELBERTON, GA
on 3/6/2008
Customer Rating:
I just got my set yesturday and I have already made 4 different jigs to use on my router table, table saw, and band saw. I am using them to hold feather boards and also to use them to hold my sacrificial fence on my table saw and my ripping fence on my band saw, if you are considering if you should purchase this wonderful accessory for your work shop.
|
|
18) Submitted by
Jason A, from Sterling, VA
on 2/20/2008
Customer Rating:
I'm going to buy another set of these guys, I use them everytime I'm at my router and table saw.
|
|
19) Submitted by
Bruce Ring, from Middletown, CT
on 2/10/2008
Customer Rating:
Good value for money spent. I use it often.
|
|
20) Submitted by
J.Stanley, from Annandale, VA
on 1/6/2008
Customer Rating:
I enjoy making most of my woodworking jigs and such stuff and using good quality parts like these. It is nice to do small projects between the bigger one.
|
|
21) Submitted by
Roger Gerdes, from San Jose, CA
on 10/7/2007
Customer Rating:
Using on featherboards to hold both sides securely.
|
|
22) Submitted by
Monte Miller, from Denton, TX
on 1/8/2007
Custom featherboards and hold-downs are a cinch with this product. Perfect for tablesaw and router operations. Nice value.
|
|
23) Submitted by
Jeff Chapman, from Aubrey, TX
on 4/3/2007
The pieces fit the table slots well however tightening the wheel bends the tracks enough to render them motionless. This should only be used for stationary purposes.
|
|
24) Submitted by
Mark
on 11/22/2009
Customer Rating: 
They work, but the screws are a little short. They need to be 1/4 inch longer for the knobs to fully engage the threads when used with a 3/4 inch thick featherboard or other fixture. And they are a special screw, so I can't just put in longer ones.
|
|
25) Submitted by
Gregory, from Santa Rosa, CA
on 1/19/2012
Customer Rating: 
This product does not fit either Bench Dog or Milescraft Featherboards.
|
|
26) Submitted by
Ruhi Arslanoglu, from Leonia, NJ
on 2/3/2008
Customer Rating:
As long as you check each slot bar and remove the burrs from the long edges which make it jam in miter slots, it does what it says it does and well. I had four pairs and only one pair did not need to clean them them up. It is easy to do so with a metal object like a hammer or something like that.
I wish it had multiple locations for the screw to be adjusted along the length instead of only one in the middle so one could bring them closer together when used two together.
|
Hand Tools and Shop Accessories 
(1)
Hardware kit allows you to make your own jigs and hold-
downs.