Customer Reviews and Photos for:
Kreg™ Universal Drawer Slide Mounting Jig
|
Average Rating:
3.4
(17 customer reviews)
$29.99
Add your review...
|
|
|
1) Submitted by
Robert Stahl, from Mishawaka, IN
on 4/4/2009
Customer Rating: 
Wish I would have purchased it years ago!
|
|
2) Submitted by
Pat, from San Ysidro, CALIFORNIA
on 5/17/2009
Customer Rating: 
Jig works fairly well I still use a bullet level on top just verify level, with longer then 16" full extension slides, the slide tends to fall off the jig. Forget about trying to use this jig unless you have cross pieces on your face frame. which is my issue at this time, the jig will not sit far enough onto the face frame to allow you to clamp it to the work. So I spent the $30 for nothing.
|
|
3) Submitted by
David Drake, from Centerville, MA
on 3/19/2009
Customer Rating:
Simple is always better... this jig is like two extra sets of hands that know exactly what they are doing! Worth the money on the first job... free after that!
|
|
4) Submitted by
Jack, from Wapello, IA
on 3/18/2009
Customer Rating: 
If and when you get tired of wasting time adjusting your drawer slides, buy this jig! Takes the guess work out of it all. Great time saver!
|
|
5) Submitted by
Drew, from Dublin, OH
on 2/7/2009
Customer Rating:
Works great, Helped me finish the cabinet much quicker.
|
|
6) Submitted by
Bob Wallingford, from Dallas, TX
on 5/13/2008
Customer Rating:
My experience with Kreg products has been nothing but positive. The Universal Mounting Jig performed as advertised. The jig was well worth the purchase, I typically build face frame cabinetry, so I can not comment on frameless applications at this time. The device was a real time saver, and well worth the dollars spent.
|
|
7) Submitted by
Dennis Dorries, from Breese, IL
on 1/19/2009
Customer Rating:
Another quality product built by Kreg and sold by Rockler. My only regret is I didn't find this product much sooner. It is very easy to use and saves a lot of time and excess measurement. Thanks Kreg & Rockler!
Solid oak coffee table
|
|
8) Submitted by
Joe, from Scharle, NC
on 7/21/2008
Customer Rating:
Handle opening needs to be larger to make clamping easier & faster.
|
|
9) Submitted by
Don McKell, from Los Gatos, CA
on 1/15/2009
Customer Rating:
There are a couple of downsides to this jig. It works best when there is a rail across the carcase at the bottom of the drawer. In addition, the jig is much less useful when mounting long drawer slides than it is when mounting slides whose length is under 2 feet.
|
|
10) Submitted by
Bill Kemp, from Greene, NY
on 4/15/2008
Customer Rating:
This weekend I finished the first drawer that I had ever built. I installed the slides using the jig and to my complete amazement the drawer works perfectly! This is a great tool.
|
|
11) Submitted by
Carl Polichetti, from Horsham, PA
on 2/1/2008
Customer Rating:
My only regret is that I did not find this product until recently. It's worth every penny I spent on it but it is best suited for face frame cabinetry.
|
|
12) Submitted by
Dan, from Elizabeth City, NC
on 5/23/2006
I do not recommend for frameless cabinets. It works better with face frame cabinets.
|
|
13) Submitted by
Scott Dittman, from Martinez, CA
on 9/15/2008
Customer Rating: 
Worked well for one set of drawers. However, with any installed base trim for a lower drawer it is unusable. Actually found that a long blade tri-square worked about as well.
|
|
14) Submitted by
Terry Horner, from Portage, PA
on 5/11/2009
Customer Rating:
I thought the magnet on the Kreg would make it better than my hommade jig. However I found the Kreg jig limited in where I could use it. My easy to build jig is T-square shaped with a 16 inch arm inside the cabinet, Kreg should stick with their fine pocket hole jigs.
|
|
15) Submitted by
Robert Hansen, from Delmar, NY
on 1/30/2011
Customer Rating:
This won't work for longer extension slides as the slide falls off the jig- I gave up using it and substituted a wood block as a spacer and short adjustable carpenter's square to keep the slide even to the back of the cabinet. Much faster and cheaper.
|
|
16) Submitted by
Bob
on 11/21/2011
Customer Rating: 
The jigs I received are not square. This is a real disappointment. I didn't realize this until it was too late. If you buy any, check to make sure they are square the minute you get them.
|
|
17) Submitted by
Tom Church, from Belvidere, TN
on 2/21/2008
Customer Rating:
I've always been a big fan of Kreg products. This product is pretty much worthless for extension slides. Neither the cabinet or drawer side will properly seat in the jig.... the slide body is about 3/32 inch from the drawer or cabinet. I do plan on discussing the problem directly with Kreg.
|
Hand Tools and Shop Accessories 
(0 Items)
