Table Saw Magnet Micro Adjuster™

Make fast, accurate adjustments in less than to your T- square style table saw fence.

Allows for precise dadoes and a perfect fit every time.
Three powerful rare earth magnets hold adjuster securely on front rail.
Mounts and dismounts in seconds without tools.

More...

With soft rubber handle for comfort.
Soft plastic cushion on adjuster head won’t mar fence.
Install and remove in seconds without tools.
No alterations to saw or fence needed.
Patent pending.

	Set the fence to within 1/4" of cut. Place adjuster against rail at 30-degree angle and slide to fence.
	Roll adjuster down tight against rail, engaging magnets.
	Adjuster should be firmly resting on top rail.
	Turn handle to adjust fence.
	To remove adjuster, pull on bottom and lift upward. Do not lift off solely with handle.

Back to overview

Customer Reviews and Photos for:
Table Saw Magnet Micro Adjuster™

Average Rating:

3.3
(32 customer reviews)

$21.99

Add your review...

1) Submitted by Joseph Josephson, from Oxford, CT on 12/27/2009

Customer Rating:

Not a bad deal, I wasn't sure if I'd ever get the chance to use it and thought it's better to have it on hand then to wish I had it when I needed it. But low and behold, the opportunity came about when I was fitting some lining to a Humidor. All the lining edges had to be on a 45 degrre angle and using the mirco adjuster made it very easy to fit them, Thanks Rockler!!

2) Submitted by Paul Evans, from Aston Twp., PA on 11/21/2009

Customer Rating:

When I bought the Micro Adjuster I knew I was going to have to adapt it to my fence bracket. I took a piece of scrap wood and cut to the size I thought would work. I than fastened it with double sided tape to see if the Micro Adjuster would work right. It worked fine. I than removed the block of wood, drilled and counter sunk two #6 screw holes to fasten the block of wood too the saddle of my saw fence. When I need to make fine adjustments, I fasten the Micro Adjuster next to the wood block as seen in the photo and make my fine adjustment.

(click to see full-size picture in new window)
Product Review for Table Saw Magnet Micro Adjuster™ - Rated 4 Stars

3) Submitted by Marty Brandt, from Annville, PA on 1/17/2009

Customer Rating:

Bought it before Christmas at great price. Works as advertized, magnets strong enough to hold it on my Biesemeyer fence. My on off switch is in the way so can't use it on cuts below 5 inches until I remount the power switch. Front of micro-adjustr hangs 4 inch below top of fence rail. Still find myself thumping as it is faster then setting up and using the micro-adjuster.

4) Submitted by Dave, from Goshen, KY on 12/10/2008

Customer Rating:

Bravo, Rockler! I recently converted my Craftsman/Ryobi table saw to a Delta fence. I missed my old micro-adjuster which could not be adapted. This micro-adjuster is easy to use, very acurate, and as someone else said, it sure beats tapping the fence!

5) Submitted by Phill, from Palmer, CA on 10/1/2012

Customer Rating:

It was working fine until I bumped the handle and the unit came apart at the seam. After reading other reviews about the same problem, I called Rockler and shared my problem and they are sending me a new one. That's what I call service. Thanks!!!

6) Submitted by Mike B Brogan, from La Crosse, WI on 12/24/2008

Customer Rating:

Very good deal at pre-Christmas discounted price. Works well with my Delta fence. Quality and strength of magnets were better than expected. Goes on and off very easilly and stores on anything metal with its magnets.

7) Submitted by Bill, from Valrico, FL on 10/11/2009

Customer Rating:

Purchasers should check their saw for a non-aluminum front. The product only works on steel table-tops!

See all 32 reviews...

Table Saw Magnet Micro Adjuster™

Customer Reviews and Photos for: Table Saw Magnet Micro Adjuster™

Customer Reviews and Photos for:
Table Saw Magnet Micro Adjuster™