Incra® Miter 1000SE with Telescoping Fence

Achieve mitering accuracy that you never thought possible! Special Edition miter gauge comes with sturdy telescoping fence and dual-arm Flip Shop Stop for accurate miter cuts on the table saw or router table.

• Precision angle indexing teeth are laser cut in solid steel to lock in 41 positive angle stops in 5º increments over a full 180º range, with special stops at 22-1/2º and 67-1/2º.
• Stainless steel vernier cursor delivers an incredible 1/10º resolution between fixed steps.
• Get perfect, repeatable accuracy every time – whether making basic 90º cut-offs, simple picture frames, complex compound miters, or a 20- sided object.

Incra precision allows you to produce perfect, gap-free hairline glue joints on the mitered corners of any multi-sided object without trial-and-error setups. Sturdy Special Edition Incra-Lock™ fence telescopes from 18" to a full 31" length. Flip Shop Stop has patented saw tooth rack system that instantly controls the length of your cut. Dual flip arms, equipped with three sliding stop rods, operate independently or in tandem for one, two or three simultaneious stop positioner setups. Made of solid aluminum with hardened anodized surface. Miter bar has six expansion disks to adjust both sides of the bar for zero side play and anti-friction travel on all table saws and router tables with standard 3/8" x 3/4" miter slots. Interlocking tongue-and-groove cooperation between the flip arms and surface of the fence insures that the sharp end of a mitered board won’t wedge itself between the fence and the stop.

Incra Miter Gauge 1000 Manual Incra Miter Gauge Datasheet Incra Miter Guage SE Manual Addendum

Customer Reviews and Photos for: Incra® Miter 1000SE with Telescoping Fence Average Rating: (4.8) (5 customer reviews) Add your review...

1) Submitted by Dustin, from Lino Lakes, MN on 1/29/2009 Customer Rating: Did a lot of research before pulling the trigger on this gauge. It is very solid...was surprised by it's weight when I took it out of the box. Easy to set up and (thus far) is holding a set very well. The long, extendable fence adds a huge amount of confidence when cross cutting boards too wide for the miter saw. Have since purchased other Incra products and have been similarly pleased.

2) Submitted by R. Gabler, from St. Marys, PA on 4/28/2008 Customer Rating: I have been searching for some time now to replace my factory supplied miter gauge. After reading reviews of several different makes, plus it was on sale, I decided to try the Incra 1000SE. My biggest complaint with my old one was being so loose in the slot causing inaccurate cuts. This gauge is great and it rides so smoothly in the slot. I am sorry it took me so long to make up my mind which one to buy. I used to have to check my setup every time to make sure I had a good cut, and now I just know it's there. My only concern is the nylon bearings they give you to take up the slack in the slot. After time they will surely wear out,though they give you several extras. I have no second thoughts about buying this gauge.

3) Submitted by David Haas, from Grove, OK on 11/10/2007 Customer Rating: Very easy to set up and use. Excellent product materials and workmanship in it manufacturing.

4) Submitted by Michael Whitten, from Saint Marys, GA on 5/3/2009 Customer Rating: Works just as advertised. Very sturdy construction with a lot of extra spare wearable parts. Very little and easy assembly and very easy to use. The only negative is that the day after I ordered the 1000SE, Rockler sent me an ad for the new 1000HD. Wish I had spent a few extra $ for the HD. The HD is indexed at every degree versus the SE indexed at every 5 degrees. Regardless I've already used the SE and love it.

5) Submitted by Mario Theodoridis, from San Francisco, CA on 3/25/2008 Customer Rating: Sweet. Very versatile and well built. One little pet peeve is that the surfaces below and above the t-slot are slightly concave, (i'd say about a degree). The overall surface is dead on, but little pieces (3/4x3/4 or less) need a backing board attached if they're to be cut at an angle. I'm not sure this is a defect, as having the t-slot slightly recessed provides for better stability of attached items.