- Overview
- More Info
- Reviews
- Videos
If you can use a plunge router, you can cut strong and perfectly fitting mortise and tenon joints in no time. Easily rout single, double, twin, quadruple or even triple mortise and tenon joints, plus angled and compound-angled joints, in stock up to 3" x 5". Virtually any plunge router will fit and still be available in seconds for other uses.
Nothing provides matching joint halves with the ease and accuracy of the new Leigh FMT! Named one of Workbench Magazine’s Top 10 Innovative Tools of 2004, the FMT Jig allows you to rout both parts of the joint with just one joint guide, one router bit and one jig setup. Make pefect joints for everything from match-stick frames and miniature tables (rout joints smaller than 1/4" — so tiny they’re almost beyond belief!) to full-size chairs and 6-foot garden gates.
- It’s remarkably easy to set up perfectly aligned multiple mortises and tenons on the FMT. Precision and repeatability are made possible by adjustable table limit stops that control the table’s range of motion in both X and Y axes.
- With each mortise or tenon position sighted and limit stops set, you’re ready to rout double, quadruple, or even triple joints with the same ease and precision as a single mortise and tenon.
- Joint tightness is infinitely adjustable by simply turning a calibrated knob; the fit is recordable and repeatable.
- Sliding cursor provides easy alignment.
- Bolts to a board and clamps to a bench.
- No dedicated router is required!
- Comes with universal sub-base that attaches to virtually all plunge routers, five 5/16" guides that will make over 20 sizes of mortise and tenon, guide stand, 5/16" spiral upcut cutter with 1/2" shank, two cam-action Speed-Clamps, outrigger bars, adjustable sidestop fence, fully illustrated user guide, screwdrivers, and mounting hardware.
- The ACMTC Accessory Kit (#39770 - Sold Separately) includes eight 1/4" guides, four 3/8" guides, four 1/2" guides, eight-piece solid carbide spiral upcut bit set, and wood storage box.
|
| |
Customer Reviews and Photos for:
Leigh FMT Pro Frame Mortise and Tenon Jig
|
Average Rating:
4.3
(8 customer reviews)
$999.00
Add your review...
|
|
|
1) Submitted by
Gary Hileman, from Farmington, MISSOURI
on 4/1/2012
Customer Rating: 
Very nice product. Setup is tedious but not hard the first time. Once you have your router "mated" with the jig this is a lot of fun. This thing takes the inexperience out of the equation. As long as you follow directions you will make some very nice joints. I would make a reference block and as you get guides make a mortise and tenon and mark it with guide size and bit size. This makes it a lot easier if you are building a project that requires several different sizes.
|
|
2) Submitted by
Paul , from Sheboygan Falls, WI
on 10/1/2011
Customer Rating:
Happy with the product, arrived in two days, spend the extra do it right!
|
|
3) Submitted by
Seamus Day, from Grand Turk
on 1/1/2010
Customer Rating:
Having read some of the comments here I cannot believe they are talking about the same machine! This is a superb machine and worth every single penny; like any machine it has limitations, but as a general shop tool it is perfect, beautifully built and engineered from top quality materials, is incredibly simple to use, versatile, finely adjustable and super accurate. Highly recommended like all leigh tools!
|
|
4) Submitted by
Matt Arnold, from Rogers, AR
on 12/5/2007
Customer Rating:
Oh yea, now this is one fine piece of equipment. Sure it cost a lot, but if you are serious about making fine furniture, then the FMT is a must in your shop. I just completed my first piece with the FMT it has show through tenons. With my normal way of making this joint, it would take me a half day and then more than likely it would look terrible. But with the FMT, it took me only 15 minutes and i held tolerances to a few thousands. So don't think twice about getting a FMT. Just do it , you will be very pleased.
|
|
5) Submitted by
Kenneth Kaiser, from Battle Ground, WA
on 11/24/2008
Customer Rating: 
The product is sturdy enough and after working with it a bit it is easy to achieve repeatable results. My problems have been with the clamping system and the alignment system (i.e. the alignment bar that can be attached for vertical milling. The clamps are a little difficult to use when you are holding the piece in position and trying to clamp it with the other and tightening it with the other.
The router mount is difficult to slide,but as I said once you have the system set up for the process it is easy to repeat with great accuracy. My other issue has been that I am assembling 46 window frames for an old railroad car. The frames require at least three different mortises for each frame. I like to build a little make a little but without a way of easily "marking" or "remembering" where your set up is you have to do all of one kind at once or go back through the set up again. With the advances in micro electronics and the cost of the jig it would seem that adding some sort of memory feature that would facilitate returning to a previous set up would not be an impossible engineering feat within the current price structure.
Also it is difficult to see for alignment purposes. I was working with pieces of window frame and trying to align the router over the location of the mortise was a challenge because it was difficult to see to align the bit. Once it was set up it was much easier and things went quickly.
It is pricy though and it would seem that the engineering costs should have been recovered.
|
|
6) Submitted by
Shane Miller, from Davey, NE
on 11/13/2007
Customer Rating:
Although this unit is rather costly it does exactly what it says it will do. My first project was building 11 different sized cabinet doors with mortise and tenon joints at each of the corners. In less than 3 hours I was done with all the joints and they fit perfectly. This time included assembling the jig, reading the instructions and several practice runs. Now that I'm set up it takes longer to set the router depth than it does to set the jig. Do recommend a very solid plunge router with a base that has little play during the plunge motion. By the way that will not be a Porter Cable. Mine and several other reviewers got poor results with the Porter Cable. I used a Freud and others have highly recommended the Bosch.
|
|
7) Submitted by
Mark Zachmann, from Chapel Hill, NC
on 7/12/2010
Customer Rating:
I think this is one of the best-designed woodworking tools I've ever used. When you try to make stupid mistakes it stops you. All the little things are done well and construction is excellent. I just did 16 tenons in about an hour and the last one was just as good as the first one. Placed right, sized right. What you want from a tool - consistent results with less effort.
Not to mention great service from the Leigh.
I'd like better dust collection - the port hole is too big for end mortises so I have to place a block in the dust collector when mortising. Otherwise it's a 10.
|
See all
8 reviews...
|
Home  Routers and Accessories Router Accessories Leigh FMT Pro Frame Mortise and Tenon Jig 
|
(0 Items)
