Rockler Dust Collector for Rockler Dovetail Jigs

Finally, an affordable dust collector for your Rockler dovetail jig! You don’t have to spend hundreds of dollars to get dust collection with a dovetail jig. Our revolutionary new dust collector eliminates virtually all the dust created when cutting dovetails. It easily attaches to Rockler’s dovetail jigs (both new and old!) and a shop vacuum or dust collection system to provide you with a clean cutting area and safe working conditions.

Easily attaches to Rockler’s dovetail jigs
Built-in 2-1/4" port fits most shop vac hoses (not included).

More...

Sliding baffle directs the dust collection to where the dovetails are being cut.
Sweep brush adjusts to provide a complete seal for stock thicknesses of 1/2" up to 1-1/8".
Contains the dust while allowing the bit to travel through without damage.
Two extra long 4" knob posts make adding your dust collector shroud easy.
Built-in 2-1/4" port fits most shop vac hoses (not included).
For older Rockler dovetail jigs with 4-screw side stops, conversion kit #25174 is required. (Sold out and no longer available).
Patent pending.

Back to overview

Customer Reviews and Photos for:
Rockler Dust Collector for Rockler Dovetail Jigs

Average Rating:

3.9
(22 customer reviews)

$47.99

Add your review...

1) Submitted by D Wilt, from Etiwanda, CA on 1/29/2013

Customer Rating:

What a great product. Easy to install and use. No more face full of chips. Almost all of the chips were sucked into the shop-vac.

2) Submitted by BJ Land, from Port Arthur, TEXAS on 3/12/2011

Customer Rating:

Very simple to install, and what a difference. No chips in the face, no chips to clean up. All the chips and sawdust go into the dust vac system hopper. Wish this had been available years earlier. This is one of the best ideas for woodworking since the router was invented. Great product.

3) Submitted by John Kirschner, from Watkinsville , GA on 10/11/2009

Customer Rating:

Works well at keeping the area clean but is a problem when installed and trying to set up the jig...need to remove in order to mark the depth of cut when doing through dovetails...I am going to slot the dust collector so I can remove it without have to totally unscrew the clamp.

4) Submitted by Don, from Houston, TX on 6/20/2009

Customer Rating:

I received my dovetail jig for dust control works perfect. I also went to our local store and found this shield was on sale, but I finished the job of cabinet drawers. Make sure the bit you have retracts into bushing so dovetails fit.

5) Submitted by Dohnn Wood, from Anchorage , ALASKA on 1/4/2009

Customer Rating:

I bought the dovetail jig first, and would have had to return it as the time saved over hand cutting was more than used in time spent trying to clean up the dust. With the dust collector this tool will be a welcome addition for cabinet drawers. thanks

6) Submitted by Dick Fornasiere, from Menomonie, WI on 12/9/2008

Customer Rating:

This product does what it says it will do. Saves alot of clean up time and does not hinder the operation of the jig or router. Worth the price.

7) Submitted by SeaWolf's Home Workshop Blog, from Jacksonville , FL on 10/19/2008

Customer Rating:

This dust collector catches 98% of all the chips and used with a vacuum modified router 99.9% of all the saw dust. It was a real pleasure not to be angle deep in saw dust. The collector does add a little difficulty in inserting the "tail" board and obscures the router bit, but the gain is well worth it. It is really a must if decided to buy the jig.

See all 22 reviews...

Rockler Dust Collector for Rockler Dovetail Jigs

Customer Reviews and Photos for: Rockler Dust Collector for Rockler Dovetail Jigs

Customer Reviews and Photos for:
Rockler Dust Collector for Rockler Dovetail Jigs