Home Routers and Accessories Router Bits Raised Panel Router Bits Freud Quadra-Cut™ Cove Raised Panel Bits with Backcutters


Freud Quadra-Cut™ Cove Raised Panel Bits with Backcutters

Freud Quadra-Cut™ Cove Raised Panel Bits with Backcutters

$119.97Each  
Currently In Stock


Average Rating: Customer Review Rating: 5.0  (4 customer reviews)




See More Images View Product Video
Rockler Advantage



  • Overview
  • More Info
  • Reviews
  • Videos
Bookmark and Share  

Freud's exclusive Quadra-Cut™ 4 cutter design provides the smoothest cuts possible. You'll get crisp, clean edges every time, even with cross-grain cuts in difficult materials.

Application: Producing panels from 3/4" stock that are flush with the doorframe for a professional, architecturally correct appearance

  • Exclusive Quadra-Cut™ design combines a backcutter with the smooth cuts of Freud's 2+2 Raised Panel Bits.
  • Shims are included to allow adjustment of tongue thickness from 7/32" to 1/4" for maximum versatility   and compatibility.
  • Patented design allows these bits to produce a full 1-1/2" wide reveal for traditional raised panel doors.
  • Cuts all composition materials, plywoods, hardwoods, and softwoods.
  • Use on table-mounted portable routers.

Bookmark and Share  
freud quadra cut benefits

Freud's Quadra-Cut™ Router Bits Feature an Exclusive 4 Cutter Design!

For the cleanest finish for routing the edges of hard or soft wood, woodworkers can look to Freud's new Quadra-Cut™ router bits. These unique, patented bits employ four cutting edges, versus the industry standard of two, for a flawless finish on the most delicate of materials.

Two of the carbide cutters have an upshear angle to remove most of the stock. Then the pair of downshear cutters make a final cut to produce an ultra clean edge.

Industry standard bits that only have two cutters can leave fuzz and splinters on the top surface, especially in cross grain cuts, but Freud's new Quadra-Cut bits leave a surface that requires no sanding or rework.

 
Item No. A B C D E R R2
35240 3-1/2" 1" 1/2" 3'' 5/32'' 1-1/2" 3/16"
 
Caution - Safety Tip:
3-1/2" diameter bits require a minimum router plate opening of 3-11/16". Use Rockler plates from group C (#27563), D (#28347) or Large blank plate (#24892).
 

Technical Documents
Bookmark and Share  

Customer Reviews and Photos for:
Freud Quadra-Cut™ Cove Raised Panel Bits with Backcutters

Average Rating:
Customer Review Rating: 5.0
5.0
(4 customer reviews)
$119.97

Add your review...
1) Submitted by JB, from Mesquite, TX on 1/11/2010
Customer Rating: Customer Review Rating: 5.0
The bit works great. However, if you are doing arched or cathedral panels, Freud's technical staff recommends doing the end cuts in a single pass using at least a 3 hp router (and hold on tight!). A less exciting way was to remove the backcutter until the cove cuts were completed by making 2 passes. Then do a full pass with the backcutter installed. It was very easy to handle the panel and my 2 hp router had no problems at all.
2) Submitted by David/Cheryl Miller, from Blairsville, PA on 11/2/2009
Customer Rating: Customer Review Rating: 5.0
The bit cuts so smooth - We are using Character Ash for our kitchen face frames & doors. We also purchased the Freud 5-pc raised panel door set. The bit cuts fit together like a glove. We fed the pieces through several times taking small swipes at a time until we achieve the cut needed to fit into the framing member.
3) Submitted by Kenneth Ewald, Sr., from Spring Branch, TX on 6/12/2009
Customer Rating: Customer Review Rating: 5.0
The bit does a great job of raising a panel.
When using any router bit, be sure to creep up on it by taking small bites, especially in wood such as Hickory that splinters easily. Also be sure to use adequate hold down (featherboard) pressure to keep the edge of the panel flat against the router table.
4) Submitted by Maurice Cash, from Grand River, IA on 1/11/2009
Customer Rating: Customer Review Rating: 5.0
I had never made a raised panel door before and was a little concerned about a 3.5" bit spinning at 12,000 RPM so close to my hands. This bit was very smooth in operation and did leave a surface that required no sanding even across the grain. I was working in white pine but have no reason that it wouldn't perform equally well in hard woods.
Bookmark and Share  

 
Order this Item
Quantity Item Number Item Stock Status Price
35240 Freud # 99-569 Quadra-Cut™ Cove Raised Panel Bits with Backcutters, 3-1/2'' Dia. x 1'' H x 1/2'' Sh.
In
Stock 		$119.97 Each



Home Routers and Accessories Router Bits Raised Panel Router Bits Freud Quadra-Cut™ Cove Raised Panel Bits with Backcutters
Locate Your Nearest Rockler Store

"I just purchased the shelf pin jig. It works great and is so simple. One of the best tools for the money that I have."
- ken - 01/11/2013
See more...
Copyright © 2013, Rockler Companies, Inc. This is a Secure Shopping Site
web2