Customer Reviews and Photos for:
INCRA Precision T-Rules
|
Average Rating:
4.7
(27 customer reviews)
Add your review...
|
|
|
1) Submitted by
SpaltedOwl, from Milwaukee, WI
on 12/31/2012
Customer Rating: 
I didn't realize it, but before I bought this measurement tool, I wasted a lot of supplies, time and ultimately money. This little gadget is outstanding. If you need accuracy - down to 64ths - this is the absolute best measurement tool you can have! As already mentioned, it is best to use a 0.5mm pencil with it. Strongly recommended and worth the $
|
|
2) Submitted by
Duane, from Rochester, NY
on 4/18/2011
Customer Rating:
Like all Incra products, this is an incredible tool. I have the 6 inch version and use it every day. A must have.
|
|
3) Submitted by
Larry Crouch, from Mayfield, KY
on 4/14/2011
Customer Rating:
The most accurate device I have in my shop for layout of wood projects
|
|
4) Submitted by
Bill Ketner, from Inwood, WV
on 4/14/2011
Customer Rating:
Best tool for accurate woodworking measurements. Has made my woodworking projects much less sloppy looking. An essential tool in the workshop.
|
|
5) Submitted by
Dan Heiman, from Hudson, IN
on 4/11/2011
Customer Rating:
I have been looking for an accurate measuring device and this is it. It holds your marker at the same measurement all the way. I used to hit something and vear off before I got done measureing. I would recommend it to anyone that needs an accurate measuring device.
|
|
6) Submitted by
Brian, from Gainesville, GA
on 6/4/2012
Customer Rating:
I bought the 12" rule this past weekend. This thing is super accurate and very nice. I wish it was a tad beefier, but I think that marking through it would be more difficult. I made 2 jigs this weekend that were superbly accurate because of this rule. I am more than satisfied with the product and the service at the retail store first time visiting. It was kind of a long drive, but well worth it. This tool will get used a lot in my home tinkering shop.
|
|
7) Submitted by
EZgoing, from Gillett, PA.
on 4/11/2011
Customer Rating:
If your looking for a very accurate lay-out tool, this is one of the best tools out there...
I have found that it works best to use a 0.5mm mechanical pencil when making marks. This helps to insure your marks are clean and easy to see.
I do feel that the unit is a bit pricey, but if you need accurate marks down to 1/64", this is one of the tools you need in your arsenal.
|
|
8) Submitted by
Chris Farley, from Winchester, VA
on 4/8/2011
Customer Rating:
Excellent lay-out tool. It is especially useful for marking multiple sides of a board and the thin metal is much easier to work with than a tri-square.
|
|
9) Submitted by
Mark R Mullins, from Chico, CA
on 2/2/2011
Customer Rating:
Excellent product: simple yet effective, I expect to buy other INCRA products in the future.
|
|
10) Submitted by
John Sartoris, from Beulah, CO
on 12/14/2010
Customer Rating:
Finally a foolproof method to lay out accurate mortise lines on the edge of boards! Thanks for a well made and well designed product.
|
|
11) Submitted by
Tim Weis, from Athens, TN
on 11/22/2010
Customer Rating:
This does everything they claim is does and more. It is the first tool I reach for when laying out a project. The accuracy of the marks, the quality of the tool, and the multiple uses make it a "must have."
|
|
12) Submitted by
Ron, from R Cucamonga, CA
on 8/16/2010
Customer Rating:
Love it, love it, love it. Need precision? Here it is. Cannot get much more exact. Use it for everything now. I am using it presently for dowel placement. Buy it!
|
|
13) Submitted by
William , from Altus, OK
on 6/18/2010
Customer Rating:
I recently purchased the 6" T-rule version to help in laying out some raised panel doors, wish I had this item years ago. This is a must have item for any woodworker, or machinist for that matter. I love the ability to mark within a 1/64th of an inch, not to mention common fractional sizes as well. I also own the 18" marking ruler, and I think Incra makes the best products.
|
|
14) Submitted by
David Lancaster, from Jackson, MS
on 2/1/2010
Customer Rating:
Very well built. Easy to use. The T-rule is very helpful in layout.
|
|
15) Submitted by
Jas from MN
on 12/18/2009
Customer Rating:
I have the 3" Tiny T, and I think it is among my most favorite tools to use in the shop. It hardly ever gets put back in the cabinet. You can't beat it's accuracy for laying out your work. I'd say a person could do about 90% of what they needed with the range of the 3" version, where the smallest measured increments are most critical.
|
|
16) Submitted by
Michael Benz, from Erie, CO
on 1/10/2009
Customer Rating:
I have the 12" version. It is most wonderful to have such precision at that length. I like that I can use it for hardware layouts on curved box front surfaces. The 12" version is too long and unwieldy for many applications. I will get a short one as well, for border, molding, and edge layouts.
|
|
17) Submitted by
Jeff, from Victor, ID
on 8/24/2008
Customer Rating:
I don't know how I got along without this! I have the 6" t-rule. Best dollars I have ever spent.
|
|
18) Submitted by
Scott Redman, from Orlando, FL
on 7/8/2008
Customer Rating:
I aready had a 18" Incra T-Rule but it can be "unruley" when trying to mark on smaller boards, especially on the edges.
The 3" Tiny-T is just right for doing markings on small pieces or board edges. Great for doing mortise layout etc.
I've also added the 6" T-Rule and Incra protractor to my layout tools collection.
Incra makes a great product!
|
|
19) Submitted by
Brian Smiley, from Burlington, ONTARIO
on 1/2/2007
My sweetie purchased the 12" version for my Xmas present...This is the best gift ever!! No more slop like a tape measure, this rule is the ultimate measuring/marking tool that I could ever have. Thanks!!
|
|
20) Submitted by
Michael Stouwie, from Harrisonburg, VIRGINIA
on 12/12/2006
I got the 12" version for myself and have fallen in love with it since the very first time I used it. It does take a little getting used to, but once you get the hang of where the scales are it is very fast and convenient.
|
|
21) Submitted by
Michael Preiss, from Houston, TEXAS
on 6/21/2006
I have the 6" version and could not imagine getting along without it. Layout is so much easier... everything from mortises to pulls. Accurate to 1/64, this little rule has saved me a lot of setup time because I have found that my test cuts end up being right on target. Be sure you have a mechnical pencil though... it won't work without one. Check out the regular rules... also very handy.
|
|
22) Submitted by
Andrew Benz, from Florissant, MO
on 4/25/2006
I bought the 6" version, and I must say it is a pleasure to use. It takes a little while to get used to the large amount of information on the face (there are a LOT of holes and a lot of markings), but as long as you double check what you're doing, accurate measurements are easy to get.
|
|
23) Submitted by
Ric Nesslage, from Denair, CA
on 3/29/2011
Customer Rating:
I haven't got to use it yet but I looked it over and it looks like perfection again, as always, with Rockler quality products.
|
|
24) Submitted by
Wolfgang Unger, from Edgewater, FL
on 8/12/2011
Customer Rating:
Got this a few weeks ago and opened it. Works very well like no other marking tool you can buy except I noticed an oddity! On the 64ths scale, each 16th was only marked as a 6! I emailed Linda at Incra and she responded within hours and immediately sent me a replacement-got it in three days. Incra is checking their stock. Don't let this dissuade you as when it comes to precision-Incra rules, and I am surely impressed with their customer service! I only bring it up so you can check yours if you already bought one. It is easy to miss! Anyway, love the accuracy and versatility of this tool and would buy anything Incra makes without hesitation! Incra has a clean website and a contact link at the top of their page.
|
|
25) Submitted by
steve rudis, from ellicott city, MD
on 9/1/2011
Customer Rating: 
Not very accurate. Would not recommend
|
|
26) Submitted by
Joshua Hoffman, from Port Washington, NY
on 8/18/2011
Customer Rating: 
I bought this tool to replace my lost wheel marking gauge. The Precision T-Rules, as the name implies, is very good at making accurate marks. It works best on fine-grain smooth wood without any raised grain. When I tried it on pine boards I frequent broke the tip off my pencil. Good for fine furniture making, but not for regular carpentry.
|
|
27) Submitted by
Brian Kent, from Riverside, CA
on 9/28/2007
Customer Rating:
I love the ruler, but have problems with using a mechanical pencil with it. On anything but the smoothest lumber the pencil lead breaks off a couple of times on every mark. On open grain like Oak or Ash, I have found that a freshly sharpened No. 2 is the only thing that will hold up. I have tried the mechanical pencils from the same shelf in the store and a couple from an office supply.
|
Shop by Brand 
(0 Items)
