A low cost alternative dust collection system! Designed for use with most open stand, contractor type saws. Dust falls into collector, which can be snapped off for quick and easy emptying.
Customer Reviews and Photos for: Less Mess Dust Collector
1) Submitted by
Judy McDonald, from Olmsted Falls, OH
on 1/31/2009
Customer Rating:
Having read previous reviews before ordering, I purchased double stick velcro which made installation a breeze. It took about 15 minutes. There's much less dust on the floor now.
2) Submitted by
Joseph VanKralingen, from Westminster, CA
on 11/14/2006
I have a portable table saw that I use in my garage and I avoided using it because I hated cleaning up the mess that it made. Now there's just a little dust on the saw which I quickly vacuum up and I'm finished. The Dust Collector works great.
3) Submitted by
Jeremy, from Rochester, NY
on 8/23/2008
Customer Rating:
Well...This is one of those products that a one who is installing it has to get creative. I agree that the directions are a waste of paper and that it is just easier to eyeball the snaps and drill away. However. finding the center of the side you're working on gives you a good reference point for the other two snaps. The screws are a little tricky too. If you have a the correct tap, it may go easier as one of my screw threads flatened right out when I tried to screw it in to my pilot hole. Unlike most of the other reviews, my snaps were a Major Pain to get snapped in. I had to to use pliers to close them over the screw heads. I'm not sure what will happen once I take them off to clear the bag. As for the performance of the bag itself; it works great. I was really happy that the bag fit my Ryobi base and I'm pleased with it so far. I just wish installation would have been easier.
4) Submitted by
John, from Poole, FL
on 12/29/2007
Customer Rating:
I installed the sawdust bag on my craftsman 10" saw and it's doing a very good job. I had trouble with the snaps holding on. I finally drilled a concave dome in a small block of wood using a half inch diameter drill bit. This matched the head on the snaps. I then snaped them on as best they would stay and placed the wood concave surface over the snaps and tapped them with a light hammer. The holding power of the snaps was improved a lot. I haven't had any come loose since.
5) Submitted by
James Miles, from Clovis, NM
on 10/1/2006
I have a contractor table saw I use in different locations and the saw dust clean up was the worse part of every job, this collector bag is simple and easy to install in a few minutes and catches at a minumin 98% of the mess. This product is well worth the price and the installation time.
6) Submitted by
Ken Robb, from Pittsburgh, PA
on 2/23/2008
Customer Rating:
Here's my tips which echo the other reviews.
1) Forget the installation directions as the snaps vary in location vertically and horizontally
2) The snaps are not self tapping so you'll need to tap the holes or secure the screws with bolts
3) The snaps are very low quality so you may want to just get rid of them and try velcro
4) You can get fabric iron on velcro at a fabric store which will work just as well
After being very satisfied with all the other Rockler products I was surprise at the shoddy quality of this one. Once I got rid of the snaps and went the velcro route the bag worked well.
7) Submitted by
Paul, from Albion, MAINE
on 2/24/2008
Customer Rating:
Bag works great but the snaps do not hold,snaps very poor quality.
" Wow you guys never cease to amaze me! I ordered some clamps & things 1 morning and got the stuff the next day. Not only good stuff but fast too! Beats running around looking for them in stores waisting gas and time! Joe Pynenberg Little Chute WI " -
Joe Pynenberg
- 01/30/2009 See more...
CART
(2.3)
