- More Info
The Shark HD 2.0 CNC Machine features enhanced electronics
for smoother movement, more power and 50% more speed to
the motors. The HD 2.0 is built to handle larger sized
routers such as the Porter Cable 890 series.
To accommodate the greater torque levels, it features
adjustable bearings to give more stability during heavy
cutting. With a table measuring 28-1/2'' x 36'', it is
ideally suited for carvings and machining operations on a
large variety of signs, doors and other projects made from
wood, soft metals or plastics. It boasts impressive power,
speed, accuracy, and ease of use. Its aluminum and high-
density polyethylene construction is designed for heavy
Simply supply a PC computer with USB 2.0 port and any
of the routers listed below, connect the USB cable to the
controller box and load the software. Includes V-Carve 7.0
software. Made in the U.S.A.
Rockler is the exclusive distributor of this item in the
CNC Shark HD 2.0 is fully compatible with the
following routers (sold separately):
- Bosch 1617 and 1618
- Porter Cable 890 series
- Porter Cable 690 series (6902VS must be manually
- Dewalt 610, 616, 618
Don't forget to download your FREE CNC Project Plans
from Woodworker's Journal!
Please note: This item can only be
shipped within the 48 Continental United States. There is
a 15% restocking fee on all CNC Shark returns.
, a new website presented by Rockler where CNC
Shark and CNC Shark Pro users can chat together, watch
how-to videos, ask questions, learn from each other and
even show off their CNC Shark projects. Now online - visit today!
Choosing the right CNC Machine for your shop can be
difficult with so many details to sift through. Whether
are a hobbyist looking to make extravagant gifts or a
to mass produce detailed wood products, Rockler has the
perfect model to fit your needs!
*Longer lengths will require support
beyond the table surface.
16,000 - 35,000 RPM
||1.5 - 2.25 HP
& .50mm (Conical)
||Depends on Material
||PC; Windows XP or
(Excluding Windows 8)
||PC; Windows XP
(w/Latest Service Pack) or Newer
Pro and Cut 3D
||VCarve Pro, Photo
Carve, ARTCAM, BMP,
|VCarve Pro, Photo
Cut 3D, BobCAD, BobART, Lazy Cam
- Enhanced electronics for smoother movement, more power
and 50% more speed to motors.
- Enhanced adjustable bearings to give more stability
during heavy cutting.
- Gantry has been redesigned for enhanced physics to
ensure more consistent machining results.
- Reinforced to handle up to 2.25 hp router.
- X and Y axis have supported linear guides.
- Z travel up to 7 inches max (2 inches more the regular
- Stronger Drive system then Plus systems.
- Increased travel on the machine with a max cutting
capacity of 25 x 25 x 7 inches.
- Automatic on and off software control of Router.
- Professional Aluminum case with Push button Estop.
- Pendant control capability included (Designed for
numeric laptop keypad).
- Extended Aluminum T slot top (28-1/2'' x 36'') for
- Precision lead Screws with anti backlash on all axis.
- Also includes: 1/2'' dia. V-groove Bit and two hold-
What's in the Box?
- Bearings: precision linear bearing guides for maximum
- USB interface with on controller memory storage.
- Precision modified stainless leadscrews with backlash
reducing nuts on all axes.
- VCarve Pro 7.0 software program included.
- Compatible with CNC Shark® Touch Probe (Sold
- Includes 1/2'' Dia. V-Groove.
- Includes two Hold-down Clamps.
- Mount for Router included (Router sold separately).
- One year warranty on parts and labor, special shipping
- Download free project plans from Vectric
(1) CNC Shark HD 2.0 Routing System
(1) One 1/2'' Dia. V-Groove Bit
(1) Two Hold-down Clamps
(1) Router mount (see above for compatible routers)
Customer Reviews and Photos for:
Shark HD Version 2.0, CNC Machine with FREE Project Plans with CNC Files!
(2 customer reviews)
Add your review...
1) Submitted by
Craig Maynard, from Beaverton, MI
I have had this system going for a couple weeks now and have made a couple easy items to start with. One does NOT have to be a machinist or computer geek to create carving projects. The Vetric program, VcarvPro 6.5, that comes with this system is a strong program that will create whatever your imagination can come up with. Vetric also has free download projects to help get started and to understand how to use them the online videos are great. I did have an issue with the Z motor connector to the drive screw. Rockler and Next Wave Automation, manufacturing company were great in resolving the issue. Not even a sour note on my part! Go figure! out of a million screws I get the short one! Would I buy it again? Yes!
2) Submitted by
Lance Putnam, from Albuquerque, NM
1. This unit is heavy. I was able to assemble it completely on my own but a second hand would have been nice. I have a custom made bench for it as you can see in the pictures. The bed weighs over 60 lbs itself and was quite the challenge to get it up the without using the table itself as a lifting point, but as you can see it can be done. The gantry weighs about 35 lbs but it very awkward to move easily. I was worried about damaging it and the mounts so my solution was to lay down a thick piece of cardboard on the table. I then took a small aluminum 2 ton car jack and placed it on the bed. I moved the gantry motor carriage to the middle to set the side to side balance evenly. I then raised the jack up to its full height and rested the motor mount of the gantry on the jacks high point. I then centered the gantry mounts and slowly lowered the gantry into place. 12 bolts later it was done. 2. With windows XP you need to follow the download instructions in the very vague and almost pointless manual and then also use the wndows control panel to search for new hardware and install it automatically as well. That will correct the missing .dll file problem. 3. This next point is so very important that it should be included in the manual. You must must must go through the WHOLE shark, yes It means removing the table, and re-tighten every last nut, bolt, and screw on the machine. I thought I would be ok and ran my first circle test cut and got a very nice, clean cut D shape instead of a 3.5" circle. I added lock-tite to the 9 screws on the lead screws that are threaded straight into plastic and to the motor coupling set screws. This was half to blame for the out of round-ness of my test cut. In total I had 29 pieces that were what I would consider unacceptably loose. The rest of the blame goes to... 4. There was an unusual amount of backlash in my Y-axis. About .05" worth which is not good in terms of accurate cuts. The culprit was the motor bearing. I tried loosening the coupler and pushing the lead screw in more but due to the flat on the lead screw also having an anti-backout feature it would not allow me to back it out far enough. My solution was to loosen all four of the motor mount nuts and bolts and then remove them one at a time a place a .05" mountain bike disk brake spacer in between the motor body and the outside of the shark chassis. This essentially removed the backlash by drawing the motor further away from the lead screw removing the play. 5. The router fit is very very tight in the lower part of the mount. I had to use fine sand paper to carefully open it up. Then I was able to coerce the router all the way down. The lock ring must be as tight as you can possibly get it. Mine was some what tight on my first cut and the router backed out to make a nice air cut for the last 50% of the tool path. 6. Hold downs- The Rockler deluxe hold downs are very nice and easy to use. Make sure you get a second set as you really should use 4 at all times just to be safe. It would be nice if the hold downs came with a couple other length t-bolts. I was nervous with the dust shoe on the first cut. They should include a few shorter lengths to keep the shoe from hitting them on thin work pieces. When you clamp them down- if you can make sure you use the middle slots on the rails as I have noticed that if I use the outer slots on the individual rails the ten to lift up when you really tighten them down. 7. There needs to be a way to set x,y, and z axis limits in the software. Almost like a integrated limit switch into the software. If you do a pocketing cut and then go to do a tool change and accidentally jog the x,y or z past its limit, it screws the whole zeroing up and then its a huge pain in the ass to reset it correctly. Will all this said and done... The Shark HD is now running like a champ. I am in awe watching this thing run.
Home Power Tools and Shop Accessories CNC Machines and Accessories Shark HD Version 2.0, CNC Machine with FREE Project Plans with CNC Files!