Designed to fit most cabinet and contractor style saws. Patented.
 This
24'' x 36'' melamine surface, supported by a 2'' solid wood frame provides a smooth,
stable surface. Includes 2 dados for miter bar clearance.
 The
unique heavy-duty mounting hardware allows for quick, easy removal without
tools or any loss of level adjustments and it folds up flat for easy storage.
Comes complete
with all hardware needed for mounting to saw including — locking, folding
leg brackets; knock-in inserts; and floor levelers-you supply the 1-1/2'' x
1-1/2'' legs. Melamine over MDF material.
The mounting bracket is adjustable from 2-1/8'' minimum to 3-1/2'' maximum to
fit almost any fence rail setup.
Hardware Kit Only
Hardware Kit only includes adjustable mounting brackets, folding leg brackets, knock-in inserts and floor glides. Questions?
See our Mounting
Instruction Sheet for this product. This may help you determine if
it will fit you table and fence combination.
|
| |
Customer Reviews and Photos for:
Rockler Table Saw Outfeed Table
|
Average Rating:
3.5
(19 customer reviews)
$121.99
Add your review...
|
|
|
1) Submitted by
Bill Reed, from Wake Forest, NC
on 5/4/2011
Customer Rating: 
I added this to my Delta 36-600 table saw, was easy to install about 1 hour. Included all the hardware necessary to install. I could have used 2 more of the spacer washers to pull the out feed table a little closer to the table, but is acceptable without. I would purchase again.
|
|
2) Submitted by
Fred Freitag, from Pittsburgh, PA
on 8/28/2010
Customer Rating: 
I like the plan. But a better way to attach the outfeed table without drill into your TS is to use 30mm magswitchs to attach to the TS back rail fence from underneath - that way there is nothing to get in the way of the TS fence if you have a glider/leveler like I do on my fence. The 30mm magswitchs have a holding power of 150# each and I used two of them. I just unfold the outfeed table legs and slide it over to the TS - then flip switches to "on". More than enough holding power and no altering of the TS itself needed.
|
|
3) Submitted by
Thomas Kelley, from Seaford, DE
on 10/4/2008
Customer Rating:
For far too long I have struggled with long panels and boards on my table saw without an outfeed table. Not only is this dangerous it can ruin the cut. So I bought the Rockler outfeed table. It went together easily. It does take a little patience making it level with your saw. But you would go through that and more if you built your own outfeed table. If you think you need this table you probably do. Don't wait like I did. Buy it now.
|
|
4) Submitted by
Joe Perrigoue, from Lake Forest, CA
on 2/5/2007
This is a great little table. My "shop" is a two car garage that both cars park in every night. Needless to say space is very tight. This table goes on and sets up in about 10 seconds. It is very sturdy (mine has cool purple heart legs) but folds up to just a few inches.
|
|
5) Submitted by
Doug Wolfe, from Green Valley, AZ
on 12/30/2007
Customer Rating:
Could have been packed better, both square corners of MDF top damaged in shipment. But I was able to repair them easily. Was surprised that some engineering was required to install it on my Delta Unisaw w/Unifence. But now that it is installed it works as as described. The best part is its portability in my very small shop. In seconds it is out of the way when not in use.
|
|
6) Submitted by
David Cruz, from Redding, CT
on 7/22/2008
Customer Rating: 
When my table arrived it was broken, a part of the hardwood support was broken off in the box with the hardware taped to it. The box was undamaged so I was surprise it was broken. The part was glue starved with some small nails it never had a chance. It was anoying I had to take time to fix something I just purchased. The hardware is of good quality. The table is okay. Beside the problems I had the outfeed table did work out nice once fixed!
|
|
7) Submitted by
Ron Thomas, from Athens, AL
on 1/30/2007
Unit is well designed and works as expected. Only problem was that all the screws holding the maple bracket to the top were striped. Not a big deal filled holes with popsicle stick pieces and a little glue and attached bracket.
|
See all
19 reviews...
|
Power Tools and Shop Accessories 
(0 Items)