1 2 Shank

  • Items 1 - 24 of 264
  • Page:
    1. 1
    2. 2
    3. 3
  1. Dovetail Router Bits-1/2" Shank

    Dovetail Router Bits-1/2" Shank

    All of our dovetail bits are specially designed with high radial and axial relief angles to give you extra clean, sharp edges. You'll find many applications for these bits. Make creative, decorative glue joints for drawers and jewelry boxes, shaker furniture and shadow boxes, sliding dovetail joints…

    2 Review(s)
    From: $14.99
  2. 1'' Dish Carving Router Bit 1/2" Shank

    1'' Dish Carving Router Bit 1/2" Shank

    This versatile dish cutter boasts two carbide wings that cut a straight edge with a rounded corner and flat bottom. Ideal for cutting hollows and recesses into shallow bowls, plates, serving trays, jewelry box trays, coasters, coin holders, spoons and lettered signs. As an added benefit, the rounded…

    3 Review(s)
    $34.99
  3. Core Box Router Bits-1/2"  Shank

    Core Box Router Bits-1/2" Shank

    Our Core Box Bits are available in several angles to cut rounded grooves and slots of varying widths that can be both decorative and functional. Sometimes called round nose bits, they are commonly used for sign-making, and are also ideal for fluted columns, finger pulls, drain grooves on cutting…

    5 Review(s)
    From: $23.99
  4. Undersized Router Bits-1/2 Inch  Shank

    Undersized Router Bits-1/2 Inch Shank

    These straight bits are slightly undersized to cut tight-fitting grooves and dadoes for plywood that is thinner than its stated nominal thickness, which applies to most plywood and veneered MDF. Typical straight bits leave an unsightly gap when used for plywood joinery. Use these bits to cut…

    21 Review(s)
    $20.99 From: $13.99

    SAVE 33%

  5. Edge V-Groove Bit, 1/2" Shank

    Edge V-Groove Bit, 1/2" Shank

    …prying or hammering. The deep channel created by the V-Groove Bit also increases the available glue surface of the joint, creating a much better glue bond. Ideal for applying solid wood edging, and for gluing up solid wood panels. All feature sturdy 1/2" shanks to maximize rigidity and cut quality.

    1 Review(s)
    From: $39.99
  6. Cove Router Bits-1/2 Inch Shank

    Cove Router Bits-1/2 Inch Shank

    …an elegant edge on drawer fronts, cabinet doors, furniture pieces and molding trim. Features an upward shear angle for more efficient and smoother cutting. Available in a range of radiuses to suit your application. 1/2" shanks provide the smoothest possible finished cut.* Two flutes.* 3/8" bearing.

    2 Review(s)
    From: $25.99
  7. Classic Cove Router Bits-1/2" Shank

    Classic Cove Router Bits-1/2" Shank

    …adding a bit of definition to an otherwise graceful curve. The bits are available in several radiuses, each with a guide bearing. If desired, a separate larger bearing can be installed to achieve a basic cove. Sturdy 1/2" shanks, the best choice for the smoothest cut.* Two flutes.* 3/8" bearing.

    0 Review(s)
    From: $39.99
  8. Edge Beading Router Bits-1/2" Shank

    Edge Beading Router Bits-1/2" Shank

    …course, you can also adjust it flush if no step is desired. A classic profile for cabinet work and architectural features, it makes an ideal beaded molding for wrapping doors and drawer fronts. These bits feature 1/2" shanks, the ideal choice when more stability and the best cut quality are desired.

    4 Review(s)
    $34.99 From: $23.99

    SAVE 31%

  9. Roman Ogee Router Bits-1/2" Shank

    Roman Ogee Router Bits-1/2" Shank

    This ogee is features a smooth curve, so the cove and round over blend seamlessly into one another. The profile works well for edging table tops, or you can use it to rout lengths of molding stock to trim out the underside of tops, soffits and built-up crown moldings.

    From: $31.99
  10. Table Edge Bit, 1/2'' Shank

    Table Edge Bit, 1/2'' Shank

    With it's generous 2-1/2" diameter, this edge profiling bit works beautifully for table tops, cabinet tops and built-up moldings. The broad round over tapers toward the edge, resulting in a lighter, less bulky look. You can profile either the bottom side or the top side of your panel to achieve…

    $79.99
  11. Classic Ogee Router Bits-1/2 Inch Shank

    Classic Ogee Router Bits-1/2 Inch Shank

    The symmetry of this edge profile exhibits a pleasing balance. A simple cove with a matching round over, nothing more, nothing less. The bit is available in several radiuses, all including a ball-bearing guide to eliminate burning. Sturdy 1/2" shanks—the best choice for the smoothest cut and…

    From: $32.99
  12. Freud Classical Roman Ogee Bit, 1/2" Shank

    Freud Classical Roman Ogee Bit, 1/2" Shank

    Add a classic design touch to cabinets, furniture, plaques, and millwork with this decorative ogee bit. It features a small step at the top, adding a bit of definition to the graceful ogee curve. Cuts all composition materials, plywoods, hardwoods, and softwoods. Use on hand-held and table-mounted…

    $44.97
  13. Piloted Flush Trim Bits 1/2" Shank

    Piloted Flush Trim Bits 1/2" Shank

    The ball-bearing pilots on these bits make it virtually impossible to cut too deep, eliminating expensive and time-consuming rework. The bearing guide is on the bottom of the shaft, below the blades, which lets you trim face frames flush with cabinet sides, shelf caps flush with shelves, or veneers…

    $27.99 From: $18.99

    SAVE 32%

  14. Rockler Restoration Beading Router Bits, 1/2" Shank

    Rockler Restoration Beading Router Bits, 1/2" Shank

    …effect. In bullnosing applications, a beading bit gives you a true half-round profile, without the flat in the middle that a round over bit would leave. It also machines the edge in one pass rather than two. All of these bits feature sturdy 1/2" shanks for extremely smooth, stable routing.

    2 Review(s)
    From: $26.99
  15. Roundover/ Beading Router Bits-1/2 Inch  Shank

    Roundover/ Beading Router Bits-1/2 Inch Shank

    …the smoothest cut available.* Includes smaller 3/8" bearing and wrench for beading applications at no additional charge.* Items with * in the description are larger bits that should be used in router tables at reduced RPM.* Two flutes.* 1/2" bearing pre-installed.* 1/2" shank for minimal vibration.

    13 Review(s)
    From: $22.99
  16. Classic Roman Ogee Router Bits-1/2" Shank

    Classic Roman Ogee Router Bits-1/2" Shank

    …balance that makes it all the more versatile. A simple cove with a matching bead, nothing more, nothing less. The bit is available in several radiuses, all including a ball-bearing guide to eliminate burning. Sturdy 1/2" shanks stabilize the bit during the cut for the finest possible finish.

    2 Review(s)
    From: $39.99
  17. Rockler Straight Router Bits, 2-Flute, 1/4" Shank

    Rockler Straight Router Bits, 2-Flute, 1/4" Shank

    One of the most common router bits, straight router bits are used to cut grooves, dadoes, rabbets, and for general purpose material removal. They are also capable of cutting mortises. Each bit has two carbide flutes that are precision ground for the smoothest possible cuts, and a long cutting life…

    11 Review(s)
    From: $13.99
  18. Rockler Straight Router Bits, 2-Flute, 1/2" Shank

    Rockler Straight Router Bits, 2-Flute, 1/2" Shank

    …square, straight-sided cuts, Rockler Straight Bits are the perfect candidates for dadoes, grooves and mortises of all sizes. All feature sturdy 1/2" shanks, which reduce vibration and chatter for a smoother cut. This in turn translates to tighter joints and stronger joinery. Two carbide flutes are…

    14 Review(s)
    $14.99 From: $9.99

    SAVE 33%

  19. 45° Lock Miter Router Bit -1/2'' Shank

    45° Lock Miter Router Bit -1/2'' Shank

    Tight miter joints are a hallmark of fine woodworking, and this bit will cut them in spades. Once cut, the miters interlock mechanically, and clamping is easy since the parts can't slide around. There is also more gluing area, so the joint is stronger than a straight miter. Machining parts with the…

    20 Review(s)
    $57.99 $39.99

    SAVE 31%

  20. 2-1/2'' Table Top Edge Bit, 1/2'' Shank

    2-1/2'' Table Top Edge Bit, 1/2'' Shank

    With it's generous 2-1/2" diameter, this edge profiling bit works beautifully for table tops, cabinet tops and built-up moldings. The broad round over tapers toward the edge, resulting in a lighter, less bulky look. You can profile either the bottom side or the top side to achieve different visual…

    1 Review(s)
    $69.99
  21. 2-1/4' Cove Crown Molding Bit, 1/2' Shank

    2-1/4' Cove Crown Molding Bit, 1/2' Shank

    The beauty of making your own crown moldings is the freedom you have in selecting materials. You can recreate this classic 2-1/4" cove molding profile in any material, including exotic hardwoods. Use it alone as a simple, elegant molding, or as a base to build upon for more elaborate moldings. Once…

    $84.79
  22. Sanding Drum 2" by 1-1/2" with 1/4" shank

    Sanding Drum 2" by 1-1/2" with 1/4" shank

    2" diameter x 1-1/2" long expanding rubber sanding drum can be used in a hand drill or drill press to smooth curved edges. Tighten the nut on top of the drum counterclockwise to expand the drum and secure the sanding sleeve. Replacement sanding sleeves available in coarse, medium and fine grits.

    $6.99
  23. Pattern Flush Trim Router Bit 1/2" Diameter x 1" Height (1/4 Shank)

    Pattern Flush Trim Router Bit 1/2" Diameter x 1" Height (1/4 Shank)

    Top quality router bits that meet the high standards of Rockler Woodworking and Hardware. Two flutes, for fast, smooth, accurate trim cuts. Precision ground to close tolerances, easily used for pattern or template cutting.

    $21.99 $15.39

    SAVE 30%

  24. Rockler Flush Trim V-Groove Router Bit, 1/2" Diameter x 1" Height - 1/4" Shank

    Rockler Flush Trim V-Groove Router Bit, 1/2" Diameter x 1" Height - 1/4" Shank

    Top quality bits that meet the high demands of Rockler Woodworking and Hardware. Bit has two flutes and 5/8" ball bearing guide. Use to trim cabinet face frames flush with cabinet sides - decorative V-groove conceals the seam.

    $21.99
  • Items 1 - 24 of 264
  • Page:
    1. 1
    2. 2
    3. 3
Feedback X