Door Clamp

  • Items 1 - 24 of 29
  • Page:
    1. 1
    2. 2
  1. Bench Block® Pipe Clamp Stabilizers

    Bench Block® Pipe Clamp Stabilizers

    …Block® Pipe Clamp Stabilizers securely hold four standard 3/4" pipe clamps at 90° for assembly of doors or frames. Set of four. Bench Block® Pipe Clamp Stabilizers can be fixed to bench or work surface to eliminate movement during clamping and prevent rotation when not clamped. * Holds…

    3 Review(s)
    $33.99
  2. Mini-X Quick Drill Kit

    Mini-X Quick Drill Kit

    …insert it so that it drops approximately two-thirds its length. (It will self-center and align with the 2nd board even if you have not preglued or clamped the components.)* Tap the dowel until fully inserted.* Trim/sand any raised portion. *The depth drilled determines the depth of insertion. This…

    7 Review(s)
    $27.99
  3. Bessey® KP Blocks

    Bessey® KP Blocks

    Use Bessey's KP Blocks with K Body® REVO™ parallel-jaw clamps for quick, square, accurate clamping of frame-and-panel doors, frames and boxes.

    $29.99
  4. 35MM Euro Hinge Drilling Jig

    35MM Euro Hinge Drilling Jig

    …indexed settings for eight hinge cup tabs ("tab" is the term commonly used for the distance from the edge of the cup hole to the edge of the door). And it can be set up to drill either small pilot holes for hinges held in place with screws or the 8mm holes used with expansion dowel hinge…

    4 Review(s)
    $234.99
  5. Sure-Hook™ 360, 12 Pack

    Sure-Hook™ 360, 12 Pack

    …on all sides of the door, your finish will dry faster.* 35mm plug adjusts to accommodate varying tolerances in 35mm bits.* Fits shallow 9mm deep cup holes and standard 13mm deep cup holes.* Works with standard 3/4" ID pipe - the same stuff used in pipe clamps.* Opening in hook is approximately…

    21 Review(s)
    $57.99
  6. Rockler Rail Coping Jig

    Rockler Rail Coping Jig

    doors of cabinets, windows and more to make clean cope cuts without blowouts - perfect for narrow cross-grain rail cuts. If you're after a cabinet door jig, look no further! Simply align material flush with the outside edge of the guide block and lock into place with the post handle hold-down clamp

    116 Review(s)
    $59.99 $49.99

    SAVE 17%

  7. Lamello Fixo — the Self-Clamping Biscuit

    Lamello Fixo — the Self-Clamping Biscuit

    Looking for a better way to connect wood pieces? These innovative biscuits actually pull workpieces together as they get driven into place. No clamps — no waiting! Use any biscuit joiner to cut grooves, then add some glue and simply pound in a Fixo. Two styles available: use the wider L-Style…

    3 Review(s)
    From: $5.29
  8. Porter-Cable® PIN138 23GA 1-3/8'' Pin Nailer

    Porter-Cable® PIN138 23GA 1-3/8'' Pin Nailer

    …when not in use* Excellent for small trim decorative moldings, cabinet crown molding, raised panel doors, rope and bead molding, mantle building, wood joining, as well as light fastening and clamping applications Specifications:* Magazine capacity: 130 pins* Firing modes: Dual trigger feature*…

    3 Review(s)
    $125.99
  9. Sure-Foot® Bench Block® Clamp Kit

    Sure-Foot® Bench Block® Clamp Kit

    …and edge-to-edge gluing, and keeps your clamp faces parallel for perfect 90° assembly. This super value pack includes four Sure-Foot Pipe Clamps (#30921) and four Bench Block® Pipe Clamp Stabilizers (#35359). Quickly and easily assemble doors, frames and other projects on your benchtop…

    4 Review(s)
    $105.95
  10. FastCap Magnetic Dust Barrier Door

    FastCap Magnetic Dust Barrier Door

    …separately), which serve as door jambs. Note: Video references clamps for securing Dust Barrier Door to door jambs. Product has been updated to include 10 magnetic strips for securing door in place. Clamps not necessary. Technical Details:* Self-closing magnetic door measures 38-1/2"W x 79-1/2"H…

    $104.99
  11. CNC Shark Routing System, with New 7.0 Software

    CNC Shark Routing System, with New 7.0 Software

    …signs, doors and other small projects. It boasts impressive power, speed, accuracy, and ease of use. With its robust steel and high-density poly-ethylene construction, it can take accidental impacts that would normally damage or destroy an aluminum or MDF machine. The included clamping table…

    20 Review(s)
    $2899.99
  12. Trim Clip Miter Aid

    Trim Clip Miter Aid

    …measure trim for windows and doors. He took it upon himself to design a tool that allows anyone to precisely measure even the longest pieces of trim the first time and every time, thus eliminating the need for multiple cuts and wasted trim.* Integral spring clamp holds the Miter Aid in…

    $14.99
  13. Door Making Kit

    Door Making Kit

    …the ends of rail doors* Takes the math out of the "equation" Rail Coping Jig* Guide block is easily replaceable to accommodate different profiles and eliminates blowouts* Durable phenolic material base measures 7-7/8" wide x 13-1/2" long* Post handle hold-down clamp allows for quick repositioning*…

    $96.28
  14. Frame Clamping Kit with Bessey K-Body Revo Parallel Clamps

    Frame Clamping Kit with Bessey K-Body Revo Parallel Clamps

    …between the clamp and the actual workpiece. Compatible with K-P clamp blocks and the K-Body Clamp Extender. Bessey K-P Clamp Blocks: This rail and stile clamping kit from Bessie provides perfect squareness when clamping doors, frames, and more. K-P Blocks allow you to cross your clamps without…

    $219.99
  15. 1X Miller Dowel System with  Clamp-it and 2 Mini Clamps

    1X Miller Dowel System with Clamp-it and 2 Mini Clamps

    …insert it so that it drops approximately two-thirds its length. (It will self-center and align with the 2nd board even if you have not preglued or clamped the components.) * Tap the dowel until fully inserted. * Trim/sand any raised portion. *The depth drilled determines the depth of insertion. This…

    7 Review(s)
    $64.66 $45.99

    SAVE 29%

  16. 2-In-1 Pistol Grip Clamps, 12''

    2-In-1 Pistol Grip Clamps, 12''

    …one-handed clamp, with an additional angle-you can link the clamps together at 90° to help keep doors, drawers and picture frames square and stable. With two clamps tightened onto the workbench and one threaded crosswise, they can work much like a portable carver's vise, allowing you to clamp

    1 Review(s)
    $24.99 $12.49

    SAVE 50%

  17. Rockwell Jawhorse HD RK9003 Workbench System - As Seen on TV!

    Rockwell Jawhorse HD RK9003 Workbench System - As Seen on TV!

    As seen on TV, this heavy-duty hands-free clamp not only secures workpieces with a rock-solid grip, its wide stable frame instantly provides a go-anywhere workstation to make cuts, drill holes, and more. Hold and cut doors, two-by-fours, two-by-twelves, and odd-shaped objects. Mount miter saws, tile…

    13 Review(s)
    $166.99
  18. Sure-Hook™ 360

    Sure-Hook™ 360

    …on all sides of the door, your finish will dry faster.* 35mm plug adjusts to accommodate varying tolerances in 35mm bits.* Fits shallow 9mm deep cup holes and standard 13mm deep cup holes.* Works with standard 3/4" ID pipe - the same stuff used in pipe clamps.* Opening in hook is approximately…

    21 Review(s)
    $5.49
  19. Powermatic® Tilt Table Mortiser w/Stand

    Powermatic® Tilt Table Mortiser w/Stand

    …swiveling vise clamp accommodates angled work pieces * Feed lever features size positions allowing for quick adjustments * Table and fence tilt from 0 to 35° for angled mortises * Gas cylinder controlled rack and pinion system for smooth head raising and lowering * Hinged chuck door allows easy…

    1 Review(s)
    $1274.99
  20. The Way to Woodwork: Woodworking's Critical Path CD from Woodworker's Journal

    The Way to Woodwork: Woodworking's Critical Path CD from Woodworker's Journal

    …drawers, doors and torsion boxes. Some of the lessons contained on this CD include: * Understanding Drawings* Calculating Board Feet* Identifying Flatsawn, Riftsawn and Quartersawn* Understanding Wood Distortion* Making Butt Joints* Adding Biscuits and Splines* Gluing and Clamping Procedures*…

    $19.99
  21. CNC Shark Pro Plus Routing System - Limited Quantities

    CNC Shark Pro Plus Routing System - Limited Quantities

    …Aluminum T slot top (28-1/2" x 36") for more versatile clamping* USB interface with on controller memory storage.* Download free project plans from Vectric* Includes V-Carve 7.0 software, 1/2" dia. V-groove Bit and two hold-down clamps!* Mounts for a Bosch Router included (Router sold separately)*…

    15 Review(s)
    $3799.99 $3499.99
  22. CNC Shark HD Version 2.0 Routing System

    CNC Shark HD Version 2.0 Routing System

    …Redesigned Extended Aluminum T slot top (27" x 36") for versatile clamping, less flex and greater accuracy.* USB interface.* Download free project plans from Vectric* Also includes: 3/8" dia. V-groove Bit and two hold-down clamps!* Mount for Router included (Router sold separately).* Z travel up to…

    $3999.99 $3899.99
  23. CNC Shark Pro Plus

    CNC Shark Pro Plus

    …graphic package provided* Aluminum T-slot top (27" x 36") for more versatile clamping* USB interface.* Download free project plans from Vectric.* Includes V-Carve 7.0 software, 1/2" dia. V-groove Bit and two hold-down clamps!* Mounts for a Bosch Router included (Router sold separately)* Bearings: 12…

    $3799.99 $3699.99
  24. 1x Miller Cherry Dowels, 40 Pack

    1x Miller Cherry Dowels, 40 Pack

    …insert it so that it drops approximately two-thirds its length. (It will self-center and align with the 2nd board even if you have not preglued or clamped the components.)* Tap the dowel until fully inserted.* Trim/sand any raised portion. *The depth drilled determines the depth of insertion. This…

    $15.79
  • Items 1 - 24 of 29
  • Page:
    1. 1
    2. 2
Feedback X