Flush Bit

  • Items 1 - 24 of 107
  • Page:
    1. 1
    2. 2
    3. 3
  1. Freud Top and Bottom Bearing Flush Trim Router Bits

    Freud Top and Bottom Bearing Flush Trim Router Bits

    …Bearing Bits let you rout half the curve in one direction, flip the work piece over and rout the other half in the opposite direction without repositioning your pattern. Perfect for templates placed above or below the work piece, or to trim laminates or veneer perfectly flush with countertops,…

    From: $34.47
  2. Freud Top Bearing Flush Trim Router Bits

    Freud Top Bearing Flush Trim Router Bits

    …as well as hand-held and table-mounted portable routers. * Features TiCo Hi-Density carbide for longer bit life and a flawless finish.* Perma-SHIELD Non-stick Coating protects from heat, gumming, and corrosion.* Each bit is computer-balanced and precision-ground for the smoothest possible cuts.

    From: $22.97
  3. Piloted Flush Trim Bits 1/2" Shank

    Piloted Flush Trim Bits 1/2" Shank

    …these bits make it virtually impossible to cut too deep, eliminating expensive and time-consuming rework. The bearing guide is on the bottom of the shaft, below the blades, which lets you trim face frames flush with cabinet sides, shelf caps flush with shelves, or veneers and laminates flush with…

    $27.99 From: $18.99

    SAVE 32%

  4. Piloted Flush Trim Bits 1/4" Shank

    Piloted Flush Trim Bits 1/4" Shank

    …these bits make it virtually impossible to cut too deep, eliminating expensive and time-consuming rework. The bearing guide is on the bottom of the shaft, below the blades, which lets you trim face frames flush with cabinet sides, shelf caps flush with shelves, or veneers and laminates flush with…

    From: $15.99
  5. Rockler Flush Door Trimming Bit

    Rockler Flush Door Trimming Bit

    …a full 2" of carbide, this bit is ideally suited for trimming thick entry doors, interior doors and countertops. It features a top-mounted guide bearing, which lets you use templates on the top side. This means better visibility when hand-holding the router. The bit is 3/4" in diameter, and features…

    6 Review(s)
    $44.99
  6. 2 Flute Shear Flush Trim Bit, 3/4" Dia. x 1-1/2" Cutter x 1/2" Shank

    2 Flute Shear Flush Trim Bit, 3/4" Dia. x 1-1/2" Cutter x 1/2" Shank

    Instead of chopping at the wood fibers at a 90° angle, the twin shear cutters on this bit slice through stock at a slight angle, producing a smoother cut than traditional straight-fluted bits. The unique design also helps eliminate tear-out problems that occur when routing end-grain, figured…

    13 Review(s)
    $34.99
  7. 1/2'' Pattern Router Bit

    1/2'' Pattern Router Bit

    With its 1/4" maximum depth of cut, this straight bit is ideally suited for routing hinge mortises and shallow dadoes. At 1/2" wide, you can rout dadoes in multiple passes to precisely fit stock of almost any thickness. Two flutes for fast, smooth, accurate trim cuts. Ball-bearing guide makes it…

    5 Review(s)
    $18.99
  8. Rockler Pattern Flush Trim Bits for Plunge Routers

    Rockler Pattern Flush Trim Bits for Plunge Routers

    The bearing guides on our Pattern Flush Trim Bits are located on the shank side of the blade, and have the same diameter as the blade, making them the perfect choice for template work when the template is fastened on the top side of the material (if using a hand-held router in the conventional way).…

    1 Review(s)
    From: $27.59
  9. Pattern Flush Trim Router Bit- 1/2 Inch Shank

    Pattern Flush Trim Router Bit- 1/2 Inch Shank

    Get fast, smooth cutting with this flush cutting bit. Top quality router bits that meet the high standards of Rockler Woodworking and Hardware. Two flutes, for fast, smooth, accurate trim cuts. Precision ground to close tolerances, easily used for pattern or template cutting.

    21 Review(s)
    From: $26.99
  10. Small Trim Router Bit Kit, 3/4" Dia. x 1" L, for 1" Thick Doors

    Small Trim Router Bit Kit, 3/4" Dia. x 1" L, for 1" Thick Doors

    …jointer. Instead, you bring the tool to the material. The kit includes one carbide router bit and five bearings to set up the various depths of cut. The bit can also be used as a double-bearing flush trim bit, as two bearings are included for that purpose. Capable of trimming stock up to 1" thick.…

    5 Review(s)
    $49.99
  11. Piloted Flush Trim Bit

    Piloted Flush Trim Bit

    Piloted Flush Trim Bit

    $34.99
  12. Freud Downshear Helix Flush Trim Bits

    Freud Downshear Helix Flush Trim Bits

    These bits are ideal for trimming 3/4" material flush with a substrate—shelf caps with shelves and face frames with cabinet sides, for example. They can also be used for trimming laminate counter tops and doing pattern work. The downshear cutting angle produces a slicing action for chip-free,…

    3 Review(s)
    From: $32.97
  13. Pattern Flush Trim Router Bit 3/4'' Diameter x 1-1/4'' Height

    Pattern Flush Trim Router Bit 3/4'' Diameter x 1-1/4'' Height

    …tolerances, this bit is ideal for pattern or template cutting. Since the bearing is top-mounted, the template is also top-mounted, and you get a clear view of the cut line. Of course, it also doubles as a 3/4" dado bit, and can be used to trim veneers and other laminates flush with the substrate.…

    21 Review(s)
    $26.99
  14. 2 Flute Double Bearing Shear Flush Trim Bit 3/4" Dia x 1-1/2" Cutter x 1/2" Shank

    2 Flute Double Bearing Shear Flush Trim Bit 3/4" Dia x 1-1/2" Cutter x 1/2" Shank

    Instead of chopping at the wood fibers at a 90° angle, the shear angle cutters on these bits slice through stock at a slight angle, producing a smoother cut than traditional straight-fluted bits. The unique design also helps eliminate tear-out problems that occur when routing end-grain,…

    13 Review(s)
    $42.99
  15. Freud # 42-110 Bearing Flush Trim Bits, 1/2" Dia. x 1" H x 1/2" Sh.

    Freud # 42-110 Bearing Flush Trim Bits, 1/2" Dia. x 1" H x 1/2" Sh.

    …is a breeze with this flush trim bit from Freud. With 1" of carbide, it's ideal for use with standard 3/4" sheet goods, as well as most 3/4" nominal solid goods. With two flutes to provide fast chip clearance, and razor sharp carbide for smooth, burn-free cuts, these bits will turn out top-quality…

    $18.97
  16. Freud # 42-114 Bearing Flush Trim Bits, 1/2" Dia. x 1-1/2" H x 1/2" Sh.

    Freud # 42-114 Bearing Flush Trim Bits, 1/2" Dia. x 1-1/2" H x 1/2" Sh.

    Among the longest flush trim bits in Freud's lineup, this bit features a full 1-1/2" of carbide length, enough to use on very thick materials. Longer bits also allow you to use more of the carbide surface, effectively lengthening the life of the carbide. Ideal for trimming laminate counter tops and…

    $20.97
  17. Freud # 42-116 Bearing Flush Trim Bits, 1/2" Dia. x 2" H x 1/2" Sh.

    Freud # 42-116 Bearing Flush Trim Bits, 1/2" Dia. x 2" H x 1/2" Sh.

    bit with enough length to trim countertops thicker than the standard 1-1/2", but the search is over. With a full 2" of carbide and a bottom-mounted bearing guide, this bit works great for sink cut-outs and template profiles on laminate substrates and solid wood materials alike. These are the bits to…

    $29.47
  18. Freud # 50-098 Top Bearing Flush Trim Bit, 5/16'' Dia. x 1'' H x 1/4'' Sh.

    Freud # 50-098 Top Bearing Flush Trim Bit, 5/16'' Dia. x 1'' H x 1/4'' Sh.

    …as well as hand-held and table-mounted portable routers. * Features TiCo Hi-Density carbide for longer bit life and a flawless finish.* Perma-SHIELD Non-stick Coating protects from heat, gumming, and corrosion.* Each bit is computer-balanced and precision-ground for the smoothest possible cuts.

    $27.97
  19. Freud # 64-100 Solid Carbide Flush Trim Bit, 1/4'' Dia. x 3/8''H, 1/4'' Shank

    Freud # 64-100 Solid Carbide Flush Trim Bit, 1/4'' Dia. x 3/8''H, 1/4'' Shank

    …tablemounted portable routers. * Features TiCo™ Hi-Density carbide for longer bit life and a flawless finish.* Perma-SHIELD™ Non-stick Coating protects from heat, gumming, and corrosion.* Each bit is computer-balanced and precision-ground for the smoothest possible cuts. Specifications:*…

    $9.47
  20. Freud # 42-106 Bearing Flush Trim Bits, 1/2'' Dia. x 1/2'' H x 1/4'' Sh.

    Freud # 42-106 Bearing Flush Trim Bits, 1/2'' Dia. x 1/2'' H x 1/4'' Sh.

    Application: Trimming laminate counter tops and doing pattern work. * These are the bits to rely on for a smooth, burn-free cut. Two flutes provide faster cutting and three flutes yield a superior finish. * Cuts all composition materials, plywoods, hardwoods,and softwoods. * Use on portable or…

    $17.47
  21. Freud # 44-100 Bearing Flush Trim Bits, 3/8'' Dia. x 1'' H x 1/4'' Sh.

    Freud # 44-100 Bearing Flush Trim Bits, 3/8'' Dia. x 1'' H x 1/4'' Sh.

    Application: Trimming laminate counter tops and doing pattern work. * These are the bits to rely on for a smooth, burn-free cut. Two flutes provide faster cutting and three flutes yield a superior finish. * Cuts all composition materials, plywoods, hardwoods,and softwoods. * Use on portable or…

    $26.47
  22. Freud # 42-104 Bearing Flush Trim Bits, 1/2'' Dia. x 1'' H x 1/4'' Sh.

    Freud # 42-104 Bearing Flush Trim Bits, 1/2'' Dia. x 1'' H x 1/4'' Sh.

    Application: Trimming laminate counter tops and doing pattern work. * These are the bits to rely on for a smooth, burn-free cut. Two flutes provide faster cutting and three flutes yield a superior finish. * Cuts all composition materials, plywoods, hardwoods,and softwoods. * Use on portable or…

    $16.97
  23. Freud # 44-102 Bearing Flush Trim Bits, 3/8'' Dia. x 1/2'' H x 1/4'' Sh.

    Freud # 44-102 Bearing Flush Trim Bits, 3/8'' Dia. x 1/2'' H x 1/4'' Sh.

    Application: Trimming laminate counter tops and doing pattern work. * These are the bits to rely on for a smooth, burn-free cut. Two flutes provide faster cutting and three flutes yield a superior finish. * Cuts all composition materials, plywoods, hardwoods,and softwoods. * Use on portable or…

    $24.47
  24. Freud # 42-100 Bearing Flush Trim Bit, 3/8'' Dia. x 1'' H x 1/4'' Sh

    Freud # 42-100 Bearing Flush Trim Bit, 3/8'' Dia. x 1'' H x 1/4'' Sh

    Application: Trimming laminate counter topsand doing pattern work. * These are the bits to rely on for a smooth, burn-free cut. Two flutes provide faster cutting and three flutes yield a superior finish. * Cuts all composition materials, plywoods, hardwoods,and softwoods. * Use on portable or…

    $16.97
  • Items 1 - 24 of 107
  • Page:
    1. 1
    2. 2
    3. 3
Feedback X