Flush Cut Bit

  • Items 1 - 24 of 41
  • Page:
    1. 1
    2. 2
  1. Freud® 91-100 13 Piece Super Router Bit Set - 1/2" Shank

    Freud® 91-100 13 Piece Super Router Bit Set - 1/2" Shank

    …round-over bit, a chamfer bit, a rabbeting bit, a cove bit and a Roman ogee bit. All bits have sturdy 1/2" shanks for minimal vibration, and the set comes in Freud's unique shadow box case, which can hang on the wall or mount on the bench to keep your bits safe and within easy reach. Bits cut

    2 Review(s)
    $220.47
  2. Phenolic Table Saw Insert Kit

    Phenolic Table Saw Insert Kit

    …size you need with a Shear Cutting Flush Trim Bit (24740, sold separately). Also works great for band saws, scroll saws, jigs and fences. Phenolic is extremely hard for optimum durability and provides friction-free sliding. It's so hard that traditional drill bits have a hard time getting through.…

    31 Review(s)
    $31.99
  3. MPower Combination Router Base CRB7

    MPower Combination Router Base CRB7

    …potential of your router in only seconds with the easy-to-install CRB7 Multi-Function Router Base. The CRB7 arms your router with the ability to cut fully microadjustable dadoes, mortises, circles, and indexed grooves for faux paneling and shelving systems. In addition to that, the offset design…

    7 Review(s)
    $79.99
  4. Freud® Top and Bottom Bearing Flush Trim Router Bits

    Freud® Top and Bottom Bearing Flush Trim Router Bits

    Double bearing design allows you to choose the cutting direction that best suits your work piece. Freud's Top & Bottom Bearing Bits let you rout half the curve in one direction, flip the work piece over and rout the other half in the opposite direction without repositioning your pattern. Perfect for…

    From: $34.47
  5. Rockler Piloted Flush Trim Router Bits - 1/2" Shank

    Rockler Piloted Flush Trim Router Bits - 1/2" Shank

    …these bits make it virtually impossible to cut too deep, eliminating expensive and time-consuming rework. The bearing guide is on the bottom of the shaft, below the blades, which lets you trim face frames flush with cabinet sides, shelf caps flush with shelves, or veneers and laminates flush with…

    From: $17.99
  6. Rockler Pattern Flush Trim Router Bit - 1/2" Dia x 1" H x 1/4" Shank

    Rockler Pattern Flush Trim Router Bit - 1/2" Dia x 1" H x 1/4" Shank

    Top quality router bits that meet the high standards of Rockler Woodworking and Hardware. Two flutes, for fast, smooth, accurate trim cuts. Precision ground to close tolerances, easily used for pattern or template cutting.

    $21.99
  7. Freud® Top Bearing Flush Trim Router Bits - 1/2" Shank

    Freud® Top Bearing Flush Trim Router Bits - 1/2" Shank

    …as well as hand-held and table-mounted portable routers. * Features TiCo Hi-Density carbide for longer bit life and a flawless finish.* Perma-SHIELD Non-stick Coating protects from heat, gumming, and corrosion.* Each bit is computer-balanced and precision-ground for the smoothest possible cuts.

    From: $31.97
  8. Rockler Shear Flush Trim Bit Router Bit - 3/4" Dia x 1-1/2" H x 1/2" Shank

    Rockler Shear Flush Trim Bit Router Bit - 3/4" Dia x 1-1/2" H x 1/2" Shank

    Instead of chopping at the wood fibers at a 90° angle, the twin shear cutters on this bit slice through stock at a slight angle, producing a smoother cut than traditional straight-fluted bits. The unique design also helps eliminate tear-out problems that occur when routing end-grain, figured…

    13 Review(s)
    $34.99
  9. Freud® Downshear Helix Flush Trim Router Bits - 1/2" Shank

    Freud® Downshear Helix Flush Trim Router Bits - 1/2" Shank

    These bits are ideal for trimming 3/4" material flush with a substrate—shelf caps with shelves and face frames with cabinet sides, for example. They can also be used for trimming laminate counter tops and doing pattern work. The downshear cutting angle produces a slicing action for chip-free,…

    3 Review(s)
    From: $32.97
  10. Rockler Pattern Flush Trim Router Bits - 1/2" Shank

    Rockler Pattern Flush Trim Router Bits - 1/2" Shank

    Get fast, smooth cutting with this flush cutting bit. Top quality router bits that meet the high standards of Rockler Woodworking and Hardware. Two flutes, for fast, smooth, accurate trim cuts. Precision ground to close tolerances, easily used for pattern or template cutting.

    21 Review(s)
    From: $26.99
  11. Rockler Small Trim for 1" Thick Doors Router Bit - 3/4" Dia x 1" H x 1/2" Shank

    Rockler Small Trim for 1" Thick Doors Router Bit - 3/4" Dia x 1" H x 1/2" Shank

    …jointer. Instead, you bring the tool to the material. The kit includes one carbide router bit and five bearings to set up the various depths of cut. The bit can also be used as a double-bearing flush trim bit, as two bearings are included for that purpose. Capable of trimming stock up to 1" thick.…

    5 Review(s)
    $49.99
  12. Bandsaw Duplicating Pin

    Bandsaw Duplicating Pin

    …shapes as you need - perfect for cathedral style doors. The pin can be adjusted to cut just a hair oversized to make final sizing quick and easy; simply leave the template in place and use a flush cutting bit to rout to the line. Attaches easily; just secure it to your guide block/bearing studs…

    8 Review(s)
    $8.99
  13. Rockler Piloted Flush Trim Router Bits - 1/4" Shank

    Rockler Piloted Flush Trim Router Bits - 1/4" Shank

    …these bits make it virtually impossible to cut too deep, eliminating expensive and time-consuming rework. The bearing guide is on the bottom of the shaft, below the blades, which lets you trim face frames flush with cabinet sides, shelf caps flush with shelves, or veneers and laminates flush with…

    From: $15.99
  14. Rockler Flush Trim V-Groove Router Bit - 1/2" Dia x 1" H x 1/2" Shank

    Rockler Flush Trim V-Groove Router Bit - 1/2" Dia x 1" H x 1/2" Shank

    …to emphasize a seam than to try to hide it. This bit does just that, applying a neat decorative V-groove along the line of the seam. Since you no longer have to sand the joint perfectly flush as you would with a typical flush trim bit, you also cut down on a lot of sanding. Just a pass or two with…

    $22.99
  15. Freud® Bearing Flush Trim Router Bits - 1/2" Shank

    Freud® Bearing Flush Trim Router Bits - 1/2" Shank

    …pattern work with templates is a breeze with this flush trim bit from Freud. With two flutes to provide fast chip clearance, and razor sharp carbide for smooth, burn-free cuts, these bits will turn out top-quality edges time after time.* Cuts all composition materials, plywoods, hardwoods,and…

    From: $18.97
  16. Freud® Bearing Flush Trim Router Bits - 1/4" Shank

    Freud® Bearing Flush Trim Router Bits - 1/4" Shank

    These are the bits to rely on for a smooth, burn-free cut. Two flutes provide faster cutting and three flutes yield a superior finish. Cuts all composition materials, plywoods, hardwoods, and softwoods. Use on portable or table-mounted routers. Application: Trimming laminate counter tops and doing…

    From: $16.97
  17. Freud® Top Bearing Flush Trim Router Bits - 1/4" Shank

    Freud® Top Bearing Flush Trim Router Bits - 1/4" Shank

    …as well as hand-held and table-mounted portable routers. * Features TiCo Hi-Density carbide for longer bit life and a flawless finish.* Perma-SHIELD Non-stick Coating protects from heat, gumming, and corrosion.* Each bit is computer-balanced and precision-ground for the smoothest possible cuts.

    From: $22.97
  18. Rockler Double Bearing Shear Flush Trim Router Bit - 3/4" Dia x 1-1/2" H x 1/2" Shank

    Rockler Double Bearing Shear Flush Trim Router Bit - 3/4" Dia x 1-1/2" H x 1/2" Shank

    Instead of chopping at the wood fibers at a 90° angle, the shear angle cutters on these bits slice through stock at a slight angle, producing a smoother cut than traditional straight-fluted bits. The unique design also helps eliminate tear-out problems that occur when routing end-grain,…

    13 Review(s)
    $42.99
  19. Freud® 64-100 Solid Carbide Flush Trim Router Bit - 1/4" Dia x 3/8" H x 1/4" Shank

    Freud® 64-100 Solid Carbide Flush Trim Router Bit - 1/4" Dia x 3/8" H x 1/4" Shank

    …Features TiCo™ Hi-Density carbide for longer bit life and a flawless finish.* Perma-SHIELD™ Non-stick Coating protects from heat, gumming, and corrosion.* Each bit is computer-balanced and precision-ground for the smoothest possible cuts. Specifications:* Overall Diameter: 1/4"* Carbide…

    $9.47
  20. Freud® 50-098 Top Bearing Flush Trim Router Bit - 5/16" Dia x 1" H x 1/4" Shank

    Freud® 50-098 Top Bearing Flush Trim Router Bit - 5/16" Dia x 1" H x 1/4" Shank

    …as well as hand-held and table-mounted portable routers. * Features TiCo Hi-Density carbide for longer bit life and a flawless finish.* Perma-SHIELD Non-stick Coating protects from heat, gumming, and corrosion.* Each bit is computer-balanced and precision-ground for the smoothest possible cuts.

    $27.97
  21. Freud® 91-103 5-Pc. Introductory Router Bit Set H 1/2" Shank

    Freud® 91-103 5-Pc. Introductory Router Bit Set H 1/2" Shank

    …by your 1/2" collet router.* Includes a flush trim, straight, Roman ogee, and rounding over bit.* All bits have 1/2" shanks.* Set comes in Freud's unique shadow box case, which hangs on the wall or mounts on the bench to keep bits handy and safe.* Cuts all composition materials, plywoods, hardwoods,…

    $98.97
  22. Freud® 91-108 9-Pc. Basic Router Bit Set - 1/2" Shank

    Freud® 91-108 9-Pc. Basic Router Bit Set - 1/2" Shank

    …profiles look equally sharp with this 9-Piece Basic Router Bit Set from Freud. With a dovetail bit, three straight bits and a rabbeting bit, you'll have the capability of cutting a full suite of high-quality joints. Use the flush trim bit to trim any veneers, laminates or thin stock glue joints…

    $176.47
  23. Freud® 99-571 Quadra-Cut™ Ogee Raised Panel Bits with Back Cutters Router Bit - 3-1/2" Dia x 1" H x 1/2" Shank

    Freud® 99-571 Quadra-Cut™ Ogee Raised Panel Bits with Back Cutters Router Bit - 3-1/2" Dia x 1" H x 1/2" Shank

    …are flush with the doorframe for a professional, architecturally correct appearance.* Exclusive Quadra-Cut™ design combines a backcutter with the smooth cuts of Freud's 2+2 Raised Panel Bits.* Shims are included to allow adjustment of tongue thickness from 7/32" to 1/4".* These bits produce…

    1 Review(s)
    $119.97
  24. Rockler Pattern Router Bit - 1/2" Dia x 1/4" H x 1/4" Shank

    Rockler Pattern Router Bit - 1/2" Dia x 1/4" H x 1/4" Shank

    With its 1/4" maximum depth of cut, this straight bit is ideally suited for routing hinge mortises and shallow dadoes. At 1/2" wide, you can rout dadoes in multiple passes to precisely fit stock of almost any thickness. Two flutes for fast, smooth, accurate trim cuts. Ball-bearing guide makes it…

    5 Review(s)
    $18.99
  • Items 1 - 24 of 41
  • Page:
    1. 1
    2. 2
Feedback X