Irwin Corner Clamp

  • Page:
    1. 1
  • Items 1 - 12 of 12
  • Page:
    1. 1
  • How-To Articles (12)
Product not found, but we found these articles.
  1. Miter Joint Tips / Rockler How-to

    Miter Joint Tips / Rockler How-to

    …yet I still end up with gaps in my miters. Being a self taught woodworker, have I missed some basic, simple steps in joining angles, mitering corners, etc? A. Michael Dresdner: "Three things come immediately to mind. First, check your tools. Cut a set of 45 degree angles, put the two boards together…

  2. Miter, Corner and Angle Clamps Assemble and Glue Frame and Corner Joints / Rockler How-to

    Miter, Corner and Angle Clamps Assemble and Glue Frame and Corner Joints / Rockler How-to

    Corner and Angle Clamps Assemble and Glue Frame and Corner Joints Miter, Corner and Angle Clamps Assemble and Glue Frame and Corner Joints posted on April 1, 2009 by Sandor Nagyszalanczy Miter clamps are made for aligning and clamping miter joints, but they work just as well for fitting any corner

  3. Building a Simple Corner Bathroom Cabinet / Rockler How-to

    Building a Simple Corner Bathroom Cabinet / Rockler How-to

    …if you use this cabinet elsewhere in your home. posted on August 1, 2009 by Don Phillips previous post next post Related Products * Titebond® III Ultimate Wood Glue View Product * Four Irwin Parallel Clamps w/Clamp Rack $191.95 View Product Leave a comment * * Name * *Email * Website * *Comment

  4. The Pack Rack - A Clamp Storage Solution on Wheels / Rockler How-to

    The Pack Rack - A Clamp Storage Solution on Wheels / Rockler How-to

    …* The Pack Rack - A Clamp Storage Solution on Wheels The Pack Rack - A Clamp Storage Solution on Wheels posted on May 9, 2008 by Rockler Where do you keep your clamps? Stacked in a corner? Mixed in with a pile of wood? Hung precariously from a makeshift two-by-four “clamp rack”? Wherever…

  5. Making Doors with Mitered Corners / Rockler How-to

    Making Doors with Mitered Corners / Rockler How-to

    …that is itself as close to perfectly flat as possible. Once the clamps are tightened down, you can and check the door for flatness by sighting along its surface, and for squareness by measuring diagonally across opposing corners (the measurements should be equal). If you've worked carefully up…

  6. How to Square-Up Projects Using Corner-to-Corner Diagonal Measurements / Rockler How-to

    How to Square-Up Projects Using Corner-to-Corner Diagonal Measurements / Rockler How-to

    …proper alignment. One big advantage of measuring from corner to corner across a clamped-up subassembly is that you can quickly check to see if that is the case. If your project is a bit out of whack, you can change your clamp positions and clamping pressure while the glue is still wet and get the…

  7. How to Build a Custom Platform Bed Frame With Cantilever Supports / Rockler How-to

    How to Build a Custom Platform Bed Frame With Cantilever Supports / Rockler How-to

    …band clamps were not long enough to clamp the mitered corners, so I used the corner blocks (pieces 7) as clamping blocks instead. Do a dry fit to figure out your clamping setup before you go further, and then glue and clamp one base side at a time to the assembly. Round over the base corners. Lay…

  8. Building the Kubb Lawn Game / Rockler How-to

    Building the Kubb Lawn Game / Rockler How-to

    …of the king piece. The four corner stakes and the hammer handle are simple white oak dowels. I used the padauk to make the kubbs, hammer head and crown of the king. Glue the set of blanks for casting pins and kubbs together and start laminating them in the long clamps. Get your game pieces off to a…

  9. How to Make PVC Pipe Chisel and Lathe Tool Storage Panel / Rockler How-to

    How to Make PVC Pipe Chisel and Lathe Tool Storage Panel / Rockler How-to

    …Glue View Product * Flat-Tipped Butt Hinges-2"L x 1-3/4"'W (Various Finishes) View Product * Jet® JWL-1015VS 10'' x 15'' Variable Speed Wood Lathe $579.99 View Product * Four Irwin Parallel Clamps w/Clamp Rack $191.95 View Product Leave a comment * * Name * *Email * Website * *Comment

  10. Making a Patio Furniture Table and Bench Set / Rockler How-to

    Making a Patio Furniture Table and Bench Set / Rockler How-to

    …by Lars Dalsgaard previous post next post Related Products * Porter-Cable 371K Compact Belt Sander Kit $132.99 View Product * Jet® 12'' Benchtop Drill Press $374.99 View Product * Four Irwin Parallel Clamps w/Clamp Rack $191.95 View Product Leave a comment * * Name * *Email * Website * *Comment

  11. Woodworking Vise Advice / Rockler How-to

    Woodworking Vise Advice / Rockler How-to

    …a bench vise as an indispensable tool, it’s an easy one to put off buying. You can get by reasonably well with an arrangement of handscrew clamps and c-clamps for a while. But eventually you’re bound to conclude that a vise will help you hold you work steadier, in a greater variety of…

  12. How to Build Table Saw Blade Storage and Organizer / Rockler How-to

    How to Build Table Saw Blade Storage and Organizer / Rockler How-to

    …Freud® LM71M Industrial Thick Stock Rip Saw Blades View Product * Freud® LU84M Industrial Combination Saw Blades View Product * Four Irwin Parallel Clamps w/Clamp Rack $191.95 View Product Comments One thought on “How to Build Table Saw Blade Storage and Organizer” * Darrell…

  • Page:
    1. 1
  • Items 1 - 12 of 12
  • Page:
    1. 1
Feedback X