Zero Clearance Inserts  Zoom

Zero Clearance Inserts

product name price quantity total
Craftsman Zero Clearance Inserts (Fits most Craftsman 10" Belt Drive saws, verify size) Item #: 69163
In Stock
 
$29.99

Each
$29.99
Jet/Powermatic 64 Zero Clearance Inserts (Will not work with Pow. #64 Left Tilt or JET Supersaw ) Item #: 69155
In Stock
 
$29.99

Each
$29.99
Delta Zero Clearance Inserts (for Right Tilt Saws Only) Item #: 69147
In Stock
 
$29.99

Each
$29.99
Craftsman Zero Clearance Inserts (Fits most Craftsman 10" Belt Drive saws, verify size) Item #: 69163
In Stock
 
Price:
$29.99
Each
Quantity:
Total: $29.99
Jet/Powermatic 64 Zero Clearance Inserts (Will not work with Pow. #64 Left Tilt or JET Supersaw ) Item #: 69155
In Stock
 
Price:
$29.99
Each
Quantity:
Total: $29.99
Delta Zero Clearance Inserts (for Right Tilt Saws Only) Item #: 69147
In Stock
 
Price:
$29.99
Each
Quantity:
Total: $29.99

Overview

Laminated 1/2" Phenolic Resin plates resist wear and offer frictionless sliding. Improved control minimizes tear out, reduces wood damage and increases safety.

 

Insert Sizes:

  • 69163-1/2" thick x 3-3/4" wide x 14" long
  • 69155- 1/2" thick x 3-1/2" wide x 12-3/8" long
  • 69147- 1/2" thick x 3-3/4" wide x 13-3/8" long

 

Please note: Because of the great variety of Craftsman saws we suggest that customers double check the dimensions of their saw before order 69163.

Tech Spec

Reviews

Customer Reviews

49 Review(s)

View All

Zero clearance works great

Don Posted October 5, 2014
I bought this for my portable table saw since the measurements were close. After some fit modifications to match my other than Craftsman saw it worked fine. I will fit another one for my dado. I would recommend this to anyone.

Craftsman insert works well with a little persuasion

Rick Posted March 10, 2014
I just got the Craftsman insert and was able to install it into my Sears contractors saw with a little effort. There were two small nubs on one edge. Not sure if these are intentional or a fault in the manufacturing. A few minutes with a file and about 5 trials and the insert slid in snuggly. I didn't even need to move either of the two adjustment screws. I just had to make some minor adjustments to the leveling screws to make it flush with the table top. The shallow dado that was already in the underside of the plate gave me sufficient clearance for my 10" blade so I was able to get in installed with the blade fully retracted. The insert is so tight in the throat I didn't even bother clamping it down with a board. I just moved the fence over it (avoiding where the blade would emerge) a safety precaution. Fired up the saw and raised the blade slowly and I was done. I can definitely recommend these.

Figured it out easily. I had...

Wes P from Hilo, HI Posted July 22, 2012
Figured it out easily. I had to adapt it to use in my cable driven Craftsman, but that was very easy also. Only bend the pin and drill a hole for the locking screw.

Write Your Own Review

Only registered users can write reviews. Please, log in or register

Videos

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012

What People are Saying:

I have been ordering from Rockler for almost 20 years and have found their products to be very inexpensive and of high quality. Shipping is fast even when an item is back ordered. The best prices I have found anywhere."

- Orval - 08/07/2012
Feedback X