VIEW
34985
$27.99
Each
In stock
Everything needed to drill mortises for 1/2" floating tenons with your Beadlock® Kit (#34802, sold separately). Includes guide block, 1/2" diameter HSS drill bit and shim set to allow you to drill centered mortises on stock thicker than 3/4" or to offset mortises.
(1) Anodized Drill Plate
(1) 1/2" HSS Drill Bit
(1) 1/2" Drill Block
(4) 0.060" Shims
(2) 0.030" Shims
(1) 1/2" HSS Drill Bit
(1) 1/2" Drill Block
(4) 0.060" Shims
(2) 0.030" Shims
| Weight | 1.0000 |
|---|---|
| Type | Guide |
WARNING: Cancer & Reproductive Harm - www.P65Warnings.ca.govWARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.
4.0 / 5.0
8 Reviews
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
An affordable solution compared to the Festool Domino. Takes a little getting used to, but it's a lot faster than some other methods.
- Was this review helpful? Yes (1) No (1)
- Flag as Inappropriate
- Was this review helpful? Yes (1) No (1)
- Flag as Inappropriate
awesome best way to make a mortise and tenon
- Was this review helpful? Yes (1) No (1)
- Flag as Inappropriate
- Was this review helpful? Yes (1) No (1)
- Flag as Inappropriate
great for big joints
the only reason this doesn't get 5 stars from me is that you have to buy the tenons as Rockler don't sell a cutter to make your own in this size.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Great little kit for the price!
This was the final addition to the Beadlock kit. I now have all three sizes. Apart from the time it takes to drill the holes and clean them up, I love this system. Recently had to drill 28 sets of 1/2" Beadlocks to join three 2x6 boards into a table top. It took a while, but the joints are really solid. Definitely a great option if you're not making hundreds of loose tenons joints.
- Was this review helpful? Yes (1) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (1) No (0)
- Flag as Inappropriate
1/2 inch beadlock guideblock
I have discovered that the right line of my guide block is too far to the right. See the picture that shows the 1/2 inch compared with the 3/8 and note the distance of the right line from the edge of the guide block. The half inch block is the one in the left of the photo (see pic #1). The result is that it throws frames off by at least 1/32 of an inch (see pic #2). One must adjust so that the line on your stock is slightly to the right of the line on the block.
Photo 2
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Drill bushing was too small for included drill
I could not drill through the bushing with the included drill until I ground the diameter of the drill smaller. This was extremely frustrating and disappointing.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions
Browse 2 questions
and 12 answers
Why did you choose this?
Rockler Store
It has a great discount
Carlos Otto C
on Feb 28, 2019
I need to join 1 1/2 inch thick material.
Gregory S
on Feb 18, 2018
It has a great discount
Carlos Otto C
on Feb 28, 2019
Currently own 3/8” but doing project with 2x6 lumber
Cynthia L
on Jul 31, 2018
The accessories included for the 1/2 beadlock indicate a 3/8 drill bit . Should it be a 1/2 inch instead?
BEST ANSWER: Yes. The bit must exactly match the hole in the guide block.
- Reply
- Inaccurate
- James C on Aug 31, 2015
- Purchased on Aug 26, 2014
Frequently Bought Together
More Suggestions