$15.99 Set
In stock

Micro Jig ZeroPlay® Guide Bar

Item #
35828
Rating:
92% of 100
Micro Jig ZeroPlay® Guide Bar Micro Jig ZeroPlay Bars Video
Micro Jig ZeroPlay® Guide Bar

Each Micro Jig ZeroPlay Guide Bar is composed of two interlocking plastic bars that adjust laterally to the exact width of your miter slot to stabilize your jigs. Guide bars are easily calibrated from the top of jigs and fixtures and are easy to retrofit. The ZeroPlay Guide Bar is a "One-Touch Calibration" miter bar (9-1/2" in length) that has two stacked half bars with opposing wedges that expand parallel evenly to fit the exact width of a standard miter slot for a perfect fit and smooth glide, even fits tricky Shopsmith™ or General's miter slots.

(1) Micro Jig ZeroPlay® Guide Bar
More Information
Brand Micro Jig
Manufacturer Part Number ZP9-B1
Weight 0.3500
Tech Spec
  • Guide Bar is approximately 9-1/4" long
  • Slot Width Range: 0.730" - 0.790" (18.54mm - 20mm)
  • Slot Depth: Minimum 5/16" (7.94mm)
  • Custom fits standard 3/4” x 3/8”, ShopSmith and General miter slots
Tech Docs
Prop 65 Warning WARNING This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov/product
4.6 / 5.0
16 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
11
3
2
0
0
Easiest Miter Bar Install
After fighting the aluminum miter bars to get an exact fit, this miter bar was super simple to install on a sled for a Sawstop Contractor saw. You'll want a 1/2" flat bottom drill bit to make life easier. Had full adjustment capabilities after install onto sled which was awesome. Highly recommend!
August 21, 2018
Woodworking Experience:
Intermediate
Love it!
Saves a lot of time trying to find the right piece & cutting it to fit. Would buy again.
July 16, 2018
Purchased
4 months ago
well designed and engineered
This item is so well decigned, engineered, and manufactured that it performed exactly as discribed. The simplisity of the guide bar made it almost intutive in mounting it to your jig. its performanse is spot on stay that way through out its use.
June 3, 2018
Purchased
5 months ago
Woodworking Experience:
Intermediate
Review of Micro jig
I have a Shopsmith which has a slightly narrower miter slot than other table saws. Therefore, most commercial miter bars will not fit. The micro Jig fits perfectly. I use one on a number of jigs I have created to enhance safety in my wood working.
August 17, 2017
Purchased
1 year ago
Woodworking Experience:
Intermediate
Does the job is was made for.
Does the job is was made for.
August 9, 2017
Purchased
over 2 years ago
Woodworking Experience:
Advanced
Dennis
Great guides. Easy to set up and use.
July 21, 2017
Purchased
1 year ago
Woodworking Experience:
Intermediate
Works as Advertised!
Easy to install and very stable! With a table saw sled, perfect 90-degreee cuts are easily repeated, with no exception. Even with temperature fluctuations, there is no need to adjust.

I saw this on a "Tommy Mac"video, but installation and alignment were somewhat easier than he demonstrated.
March 11, 2017
Purchased
1 year ago
Great Product
Great easy install, recommend a pair instead of one zero play bar when building larger size jigs. You do not really need the zero play stop as you can easily make your own.
July 28, 2016
Purchased
over 2 years ago
Woodworking Experience:
Intermediate
Micro Jig Guide Bar
Excellent product, very good quality, easy to follow instructions.
September 9, 2015
Purchased
over 3 years ago
Woodworking Experience:
Intermediate
Great for making tablesaw sleds
I have tried making guides out of wood and plastic with limited success. Also I have used three guides made of metal and this product beats them all. Not only is it easy to install, it is light weight and should not wear down over time like the other materials. It works great as a single runner on every one of my sleds.
July 14, 2015
Woodworking Experience:
Advanced
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 8 questions Browse 8 questions and 25 answers
Why did you choose this?
Rockler Store
To make a special sled
Juan A. S on May 3, 2018
would rather have had the 18" miter bar but the reviews on those were poor. Have used these in the past and they are not great but ok.
Tim T on Dec 11, 2017
To make a special sled
Juan A. S on May 3, 2018
Want to make my own sled and the reviews on this looked great
jkucharik on Feb 15, 2018
would rather have had the 18" miter bar but the reviews on those were poor. Have used these in the past and they are not great but ok.
Tim T on Dec 11, 2017
I needed it.
Stanley B on Aug 12, 2017
I'm hoping to be able to grind it down a bit to fit in my band Saw's non-standard miter slot.
David M on Jul 21, 2017
its look good
Luis L on Jul 14, 2017
saw several videos and wanted to improve my current sled.
Kevin G on Jan 25, 2017
Making a table saw sled, wanted something not prone to humidity issues
Barry M on Jan 2, 2017
Making a new cross cut sled for the table saw.
MARK B on Nov 24, 2016
building a crosscut sled
raymond d on Nov 21, 2016
video shows how easy it is to get exact miter slot tracking without worry of distortion due to change in humidity.
Evie W on Nov 11, 2016
Easy to adjust to fit groove. Slides easily and does not change with humidity.
Stuart S on Oct 28, 2016
This is the "Cadillac" of guide bars for your table saw jigs. You can always cut your own, but this one allows you to dial it in for a snug and smooth fit that's hard to master with wood only.
2Dog Projects on Jan 6, 2016
Have made jigs with two others and find them very accurate.
Stuart on Nov 25, 2015
Was having problems building my own sled. The sleds I have built keep coming out loose and messing up my cuts. I saw these on several woodworking YouTube videos. Hopefully they work.
Edgar U on Sep 16, 2015
needed to build table saw and router table jigs
Jim S on May 18, 2015
Want to make my own sled and the reviews on this looked great
jkucharik on Feb 15, 2018
I needed it.
Stanley B on Aug 12, 2017
I bought the zero play and it doesn't fit in my tablesaw tracks. Do they make a smaller size?
Jason C on Oct 28, 2016
BEST ANSWER: If your tablesaw has standard 3/4 x 3/8 inch tracks the ZeroPlay guide bar will most certainly fit in them. On the instruction sheet follow assembly steps 1 through 5 which coordinate with illustrations A, B and C. If you don't have the ZeroPlay Stop referred to in step 2, clamp a piece of scrap wood of the proper dimensions into your track that will serve the same function as the ZeroPlay Stop.
Will this work on my DeWalt dw745?
Richard M on Dec 14, 2017
BEST ANSWER: The slide will fit any saw with the standard 3/4" track. Measure width and depth of track to determine if it is 3/4 x 3/8. The slide will adjust to make a tight fit with little to no movement side to side.
I saw where one reviewer said that one bar was enough for a table saw sled. Has anyone else found that to be true?
JOE Z on Apr 7, 2016
BEST ANSWER: There is a little play in your sled if you use only one. For a cross cut sled, I would use 2.
Description says this sold as a set. What is meant by set? Is it 2 bars?
Jerry on Aug 29, 2018
BEST ANSWER: The set includes two interlocking plastic bars and the associated assembly hardware.
I have two craftsman table saws mod # 137.218020 and 137.218072. They both have tabs on the top, and both are just a tad ov er 3/4 inch wide and are 3/8 inch dxeep. Will this jig fit my saw's?
gunslinger on Dec 28, 2017
BEST ANSWER: I have a DeWalt table saw with a similar set up as your Craftsman. The Rockler jig fit and could be adjusted for zero play without any problem.
How faw apart (center to center) and what size are the mounting holes?
Wm M on Jun 20, 2017
BEST ANSWER: They are 4" o.c. and the holes take a 1/8 " drill bit
I have an older Ryobi table saw - will this work in 5/8" miter slots, they are not Tslots. I have a ryobi bts10?
Eddy H on Jun 25, 2015
BEST ANSWER: Sorry no, this has a Slot Width Range: 0.730" - 0.790" (18.54mm - 20mm) and Slot Depth: Minimum 5/16" (7.94mm).
More Suggestions