VIEW
GRP40142
12'' Inch x 8 Foot Veneer Rolls with 10 Mil Paper Backing
Stable 10 mil paper backing prevents splitting and provides excellent adhesion for your veneering adhesive.
Item #
GRP40142
A wide selection of premium veneers, all carefully matched and cut to 8' lengths. Each sheet is reinforced with a 10 mil paper backing that provides stability and helps prevent checking. Use for laminating full-length sheet stock or cut down to size for use on smaller projects. Carefully matched for the most attractive grain patterns. Spliced seams are virtually invisible.
(1) Veneer with 10 Mil Paper Backing, 1' x 8' Roll
| Weight | 1.2500 |
|---|---|
| Tech Spec |
|
| Application Size | Large |
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 8 questions
Browse 8 questions
and 21 answers
Why did you choose this?
Rockler Store
I have a drawer face that is S curved, Will this work with the grain horizontal ?
BEST ANSWER: I used this veneer to replace veneer on an entry door for a client that had delaminated because of moisture damage. I applied the veneer using Titebond II on both surfaces, letting the surfaces dry, and then ironed them on using a brown paper to protect the wood from scorching. Your success will be determined buy the amount the curve and your ability to heat the curved surface. Rockler also carries a veneer that has a 3M adhesive already on it. I used this product on another door on the same house just to try different methods. This later method make work better on a curved surface using a veneer roller to press it on.
- Reply
- Inaccurate
- James M on Mar 28, 2018
- Purchased on Aug 15, 2016
is this material actual wood or a plastic?
BEST ANSWER: Hi Philip, This product is actual wood veneer with a thin paper backing. I needed to reface a drawer front from a 1940's cedar chest that I restored for my daughter. It worked out perfectly. Hope this helps and good luck.
- Reply
- Inaccurate
- JOHN G on Jan 9, 2017
- Purchased on Aug 5, 2015
I have a table leaf I need to replace the mahogany veneer to match the other 2 leaves. Would you recommend the peel and stick veneer or veneer you apply the glue to?
BEST ANSWER: I bought the peel and stick. I worked perfect. The only potential issue is it is so sticky that you get one chance to get it right. You cannot move the veneer around. When I buy more I will buy the sticky back veneer.
- Reply
- Inaccurate
- JAMES B on Aug 21, 2018
- Purchased on Nov 14, 2016
What is the thickness?
BEST ANSWER: About 0.022" to 0.024" thickness.
- Reply
- Inaccurate
- Tim P on Jun 4, 2018
- Purchased on Jul 24, 2016
ARE THESE STAINABLE?
BEST ANSWER: Yes, I used it to reface the large bottom drawer on a family antique buffet. It looks great.
- Reply
- Inaccurate
- Danny W on May 14, 2017
- Purchased on May 18, 2015
Can this product be used to reface kitchen cabenits?
BEST ANSWER: Yes, I've used these Veneers for make new cabinets. I would imagine you could use veneer for refacing. Fitting could be challenging at the edges coming together at different angles. I've used veneers only on inside corners. If you have face frames I would use 1/8 or1/4 prefinished plywood on the frames as it would easier to produce accurate cuts on a table saw. The door are bit more challenging. I would just buy new fronts and hang doors pre finished.
- Reply
- Inaccurate
- MIKE B on Nov 23, 2018
- Purchased on Jun 19, 2017
Can u use it on steps?
BEST ANSWER: On risers but not treads
- Reply
- Inaccurate
- Robert M on Apr 15, 2019
- Purchased on May 1, 2017
Walnut paper backed veneer, is the color close to how it shows on your site?
BEST ANSWER: I would say very much so.
- Reply
- Inaccurate
- Thomas Z on Aug 29, 2017
- Purchased on Dec 3, 2015
Related Products
More Suggestions