In stock
Grouped product items
Product Name Price Qty
Lift-O-Mat Gas Springs, Black, Model 100N
Lift-O-Mat Gas Springs, Black, Model 100N Item #: 32924
In stock
$49.99
Set
Lift-O-Mat Gas Springs, Black, Model 150N
Lift-O-Mat Gas Springs, Black, Model 150N Item #: 34373
In stock
$49.99
Set

Lift-O-Mat® Gas Spring Lid Support

Item #
GRP10807
Rating:
86% of 100
Lift-O-Mat® Gas Spring Lid Support Lift-O-Mat® Gas Spring Lid Support Lift-O-Mat® Gas Spring Lid Support Lift-O-Mat® Gas Spring Lid Support Lift-O-Mat® Gas Spring Lid Support
Lift-O-Mat® Gas Spring Lid Support
Frequently bought together
  1. For upward swinging doors and lids
  2. +
  3. Separable Hinges for Lids
Total price: $0.00
  • This item: Lift-O-Mat® Gas Spring Lid Support $0.00
    Grouped product items
    Product Name Qty
    Lift-O-Mat Gas Springs, Black, Model 100N
    $49.99
    Lift-O-Mat Gas Springs, Black, Model 150N
    $49.99

Effortless opening of doors and lids! Gas springs are the ideal choice for cabinet doors and lid supports that open upward. You'll get soft and quiet closing, plus smooth motion and stopping. Each set includes two gas springs and four mounting brackets. (Screws not included). Available in Black (Silver shown not available).


Note: See the Selection Guide below for more information on choosing the correct Gas Spring Lid Support

(1) Set, Lift-O-Mat® Gas Spring Lid Support
More Information
Weight 0.5800
Tech Spec
  • Minimum door height: 10-1/2"
  • Maximum door height: 24"
  • Requires 2 Gas Springs Per Application; Sold in Sets of 2
  • Set includes two gas springs and four mounting brackets (Screws not included)
  • Easy installation
  • Black Finish
4.3 / 5.0
42 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
29
4
4
1
4
It makes my life so much easier!
December 30, 2017
Purchased
1 year ago
Woodworking Experience:
Intermediate
Four Glass doors in a bookcase
I was worried that these 1/4 safety glass doors would be too heavy for the hardware.
They are about 2 feet square with a 3in painted poplar frame.
I got the strongest set and they work very well.
We followed the directions and the installation was smooth.
Our only trouble was that, since the doors are in pairs, we had to play around a bit to get the doors aligned when open.
But the clients love them so I look like a genius.
December 27, 2017
Purchased
1 year ago
Woodworking Experience:
Advanced
Gas lifter
They worked perfect.
December 12, 2017
Purchased
1 year ago
Woodworking Experience:
Intermediate
Great product.
It does the job intended for, good quality and strong. It requires 2 people for installation but an experience carpenter can do it alone.
User submitted image
Added Aug 29, 2017
August 29, 2017
Purchased
over 3 years ago
Woodworking Experience:
Advanced
WORKED GOOD
USED IT TO HOLD UP LID ON WALL PORCH TV CABINET. USED JUST ONE SUPPORT . LID 25" X 44" MADE FROM CEDAR
August 17, 2017
Purchased
1 year ago
Woodworking Experience:
Intermediate
lift-o-matic gas struts
Work great. Easy to install
February 21, 2017
Purchased
1 year ago
Woodworking Experience:
Intermediate
Gas Spring Lid Support
The lift supports work great! I was surprised to see that they help with a the door going up as well as down. Will definitely use on other projects.
February 13, 2017
Purchased
1 year ago
Woodworking Experience:
Intermediate
Lift doors
Great product and easy to install. I highly recommend it!
January 10, 2017
Purchased
1 year ago
Woodworking Experience:
Advanced
Absolutely Perfect
Would highly recommend these gas shocks for any type of cabinet door support or equivalent applications.
AAA+++
Excellent gas spring supports to hold up my 32" smart tv & cabinet door in my RV
Excellent gas spring supports to hold up my 32" smart tv & cabinet door in my RV
December 18, 2016
Purchased
over 2 years ago
Woodworking Experience:
Beginner
lift-O-mat Gas Spring Lid Support
These are great. Holds my cabinet doors that open up at 90 degrees. They are very firm and for most average cabinet doors you may only need to place one rather than one on each side
August 7, 2016
Purchased
over 2 years ago
Woodworking Experience:
Advanced
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 27 questions Browse 27 questions and 77 answers
Why did you choose this?
Rockler Store
Needed a lift for a cabinet door in the galley of my boat
Roger I on Jun 25, 2018
for my grandson's toy box
Steve T on May 27, 2018
Needed a lift for a cabinet door in the galley of my boat
Roger I on Jun 25, 2018
they are the only ones that actually work !
Dave B on Jun 5, 2018
for my grandson's toy box
Steve T on May 27, 2018
Spring support did not work.
Morgan K on May 24, 2018
I needed strong support for a heavy oak industrial cart top which opens vertically to access compartments for remotes, papers and publications.
Stephen G on May 10, 2018
I need to complete my latest project
Ronald L on Apr 16, 2018
toy trunk project - to keep little fingers safe from the heavy lid
TANIA W on Feb 18, 2018
It works.
Robert B on Jan 27, 2018
To replace existing Lift O Mats that were installed 10 years ago.
Pam P on Dec 6, 2017
Making Tack Trunk for granddaughter. Safety!
Cheryl C on Dec 5, 2017
I have heavy cabinet door.
PAUL R on Nov 20, 2017
The spring lid on mh cabinet broke.
Judy V on Apr 22, 2017
lift door on horzine door
trying them our
Thanks
Wesley D on Apr 6, 2017
Fit my application. Recommended by your product specialist named Rick
Mike on Jan 31, 2017
They are replacement parts
Denise G on Sep 1, 2016
I bought a cabinet and wanted to lay it on its side and open them with hinges but nothing would hold them open so decided to order them
wilma R on Aug 20, 2016
We used these for two cabinets that raised up. I love them because they hold the door very securely. The instructions could have been better but the second one went smoother than the first.
Michele E on Aug 10, 2016
Support for a door/picture frame over a tv cabinet.
Rich H on Jun 27, 2016
I find the quality of all items I purchase at rockler to be finest around
John W on Jun 3, 2016
replacement for old equipment.
Stephen T on Jun 1, 2016
Great item for bottom lift doors.
Richard D on Apr 17, 2016
for a chest i build on our deck
Richard W on Mar 30, 2016
Smooth controlled open and close gas springs were a must.
Robert G on Mar 21, 2016
Over-refrigerator cabinet doors where side swinging doors would be in the way
Robert M on Feb 8, 2016
router table lift
Larry on Jan 28, 2016
Found information from your online chat that assisted me in selecting the the appropriate size gas strut.
Stephen M on Jan 22, 2016
From the comments of other buyers it looks like this is perfect for a t0y box for a small child.
Jerrold G on Jan 12, 2016
To support a toy box lid
Brad H on Dec 20, 2015
4th option - we hope it works
Nastasi A on Nov 19, 2015
I needed to replace some existing gas springs and I found the exact replacement with Rockler after searching may other vendors and sources
Simon H on Nov 18, 2015
Need to replace hydraulics on a large cabinet door
Melanie M on Jul 31, 2015
I built a storage bench and need something to hold the lid open when it is lifted up.
Greg H on Jul 16, 2015
frame mounted cabinet doors
Joseph D on Jul 9, 2015
Fixing Pontoon and found I needed to replace my old ones
Carst R K on Jul 6, 2015
For a child's toy box. We used them before and had good results.
Carol M on Jul 3, 2015
I'm currently using lift-o-mat gas spring and this item is a replasment
Alexander B on Jun 28, 2015
was looking for a support for the pirates chest i built for my grandson and could no find these light weight ones like I found on your site.
Gene O on Jun 17, 2015
I was looking for a way to lift and secure a heavy cabinet door for my garage cabinets. This will work perfectly.
Adrian M on May 31, 2015
Needed replacement for existing gas spring
James M on May 29, 2015
Building an outside cabinet with a heavy lift door and need quality lift support and hold-open function hardware.
Rush I on May 12, 2015
Referred by a woodworking blogger who used these supports on a tack trunk
david t on Apr 19, 2015
We bought the lighter weight lifts for our upper kitchen cabinets several years ago, and thought we had ordered the heavier ones for the largest door. The lighter weight lift operates to lift the larger door, but it slowly falls half way down, so we're ordering the stronger 150 to keep the door up. We have really enjoyed having the cabinet doors open upwards.
Frances G on Apr 18, 2015
they are the only ones that actually work !
Dave B on Jun 5, 2018
Spring support did not work.
Morgan K on May 24, 2018
I have a toy box I built for my grandson. The lid is 21.6 pounds and 23" front to back. I need the proper supports for a child to open it easily and not slam his fingers in it when closing. What hardware do you suggest?
Herb W on May 28, 2016
mine is in the extended position and i need it to close before i can install it---but i cannot get it to close. Any ideas?
nancy on Nov 23, 2015
BEST ANSWER: You will need to adjust the angle of the attachment to the top and side of the cabinet
What hinge should be used with the springs for ace frame overlay cabinets ?
john g on Dec 29, 2015
BEST ANSWER: We used full overlay Grass European style hinges....they worked fine.
The trick was to accurately determine the pivot point since the installation measurements work from that point.
Would they work on a trap door on a play house?
Ed R on Jun 19, 2015
BEST ANSWER: Perhaps. It would depend on the weight of the trap door and on its design.

The overview section of the product page shows the recommended door weights for the various gas spring models. If your door is within one of these weight limits you should be OK - tho if I were you I would maybe get a more powerful spring than the table indicates in order to compensate for the fact that I believe these springs are designed to lift a vertically hung ( e.g. hinged at the top) door.

A bigger issue for you might be how wide the springs open. You can see from the photos on the product page that the hinge assembly will limit the opening angle to less than 90 deg - which for a trap door would mean that entry/exit thru the trap door will likely require bending/crawling thru an opening on one side only.

Good luck
I need to install on a face frame cabinet with inset doors. Can this be done?
Bill on Jun 19, 2016
BEST ANSWER: I am pretty sure they can. It has been awhile since I have seen the installation sheet but I do believe they give the layout in the instructions.
my closet door will not close all the way. how do I adjust the gas pressure?
Judy V on May 2, 2017
BEST ANSWER: Hi Judy,
I believe it he's more to do with the location of the mounting brackets. I'm not sure if there is any physical adjustments on the spring itself.
If it is possible to disconnect one of the brackets (ideally one with more room to be relocated), and close the door then mark the location of the bracket with the door in the closed position. Once you mount it and reattached the spring, it should close all the way.
I hope this helps!
Daniel
can they be used in combination with european hinges when the door is inserted in the frame, not overlayed?
A shopper on Jun 11, 2015
BEST ANSWER: I have used these many times with the European style hinges and they have worked perfectly. However, I have not used them on an inlay door. However, the principles are still the same with the hinges whether they are inlay or overlay and the same would go for the gas springs. The hinge determines how the door opens and the gas springs only hold it up, so I would say that you should be fine.
does anyone know if these work well for a flush inset door?
A shopper on Jun 2, 2015
BEST ANSWER: they worked great for me. easy to install, and no problem with supports that were installed 4 years ago
bought gas lifters several years ago from Rockler, but now they won't hold the door up. Do they need some kind of gas refill? Don't know what to call it.
Regina C on Nov 11, 2018
BEST ANSWER: We had the same problem, ended up replacing them with the next size up which were more heavy duty. Not refillable.
Part 32924 (smallest version of this hinge): what are the dimensions of the bracket face attachment for the part of the hinge that attaches to the cabinet door? I'm using a door with lites/mullions and glass and am concerned that the mount will be larger than the wood frame of he door. Thanks! Mary Ellen
Mary Ellen W on Dec 4, 2016
BEST ANSWER: The part of the hinge at the top of the door is 3 inches wide, with 3 screws. The outside screws fasten at 3/4 inch in, and the middle screw fastens at 1 inch in. The part of the hinge with the arm is attached at 1 !/4" with screws and the metal extends 1 5/8" from the edge of the door. You will need at least 1/4 inch to make room for the screws to hold. In other words, the top frame of your door needs to be 1 1/4" and the edge of your frame needs to be 1 5/8".
Would these work on a bin type cabinet? I have a custom made built in hamper (door with a wooden box mounted to it) that needs something to 'slow it down' when being operated, especially when closing. There is room on both sides inside to accommodate these.
rewdwuerkz on Oct 25, 2016
BEST ANSWER: Hi,
Should work fine if the weight of the door is matched to the operational guide found in the overview...
I hope this helps...
Can you adjust the tension on the gas spring?
A shopper on Apr 22, 2015
BEST ANSWER: No. U must order the proper lift pressure based on the weight of the cabinet door
Need this for old shallow wooden desk with heavy lift top. How much depth do I need in the desk?
Peggy K on Dec 7, 2018
BEST ANSWER: Depth needed depends on your positioning geometry of the unit, but 3" +/- should be adequate. Care should be given to the mounting points, as there will be a lot of force concentrated there due to the pressure and mechanical leverage the units have when in the closed position
Hello - I need a "vertical lift" and am considering using this. My spice cabinet lift needs a total vertical travel of 10 to 12" downward direction - not. lift and hold, rather pull down and then push up. Has anyone used this in this vertical application ? OR do you have another recommendation ?
Mike M on Dec 23, 2017
BEST ANSWER: I used the lift as in the picture, auto lift to open and hold - pull down to close, i.e. door hinged at top, for an over refrigerator kitchen cabinet. I see no reason why it would not work well in the opposite direction though.
I have built a TV enclosure that is made out of a lighter weight pine material, it is 32 " tall 38" wide and 7" deep, I would like to add these to open the door, however I am confused on how to determine what I need. Could someone advise me on the correct version? Thanks
barry w on Aug 27, 2017
BEST ANSWER: Hi, I did purchased a pair of Lift O Mat for my TV and it work perfectly. You have to determine how high the door must lift it would be your personal desire. My cabinet was close to the ceiling so I had to make sure the door didn't hit the ceiling.
Hi I have a wall concealment cabinet that holds a couple rifles. The vertical door measures 27" tall do you think the ones that are for a door up to 24" work.?
Gary P on Aug 3, 2016
BEST ANSWER: It should work, it just depends on how heavy of a door you're using...
I have a lift up door that is 42" high and 60" wide, weighing about 35 pounds. Is there similar hardware that will work?
Mark W on Jun 21, 2016
BEST ANSWER: I think that even with one on each side, you may be pushing it. My suggestion is that (depending on where you live) you go to your closest marine hardware supplier and see what he has in stock. Boats use these frequently and most marine equipment dealers have a variety of gas springs.
I have a door that is only 8" tall...is there anything that would work with that size. it is 36.5 wide and aprox 6-10lbs in weight,,,?
Lisa P on Jun 20, 2016
BEST ANSWER: The only ones I could find was item #66621. This is an overhead bin hinge
How do you know where to mount gas springs for first time installation (not replacement)? I have a cedar storage box with a lid that weighs over 100 lbs. and is 10' x 40". I cannot lift it without some assistance.
Mel B on Jun 19, 2016
BEST ANSWER: Mel . . . These gas spring supports, even the most heavy duty, are not likely to hold your 100 pound lid open. They should help a bit with the load however. I am surprised that there is nothing in the installation instructions about hardware placement. If you look at the drawing, the lid is open to about 80 degrees. Lid side bracket attachment is down from the top about 25% of the total door height. Since the hardware has to fold into the cabinet when closed, you should be able to attach the door end, hold the door open to about 80 degrees, fully extend the movable rod in the device and determine the inside cabinet end location. Make sure the door end bracket is far enough away from the edge of the door to avoid interference but still aligns with the inside of the cabinet bulkhead when closed and that the bracket that mounts to the inside of the cabinet bulkhead is set far enough back from the front edge of the cabinet to allow the door to close completely.
I'm replacing the model BPG2810. Which one is it?
Brant S on Feb 25, 2016
BEST ANSWER: I used these liftomatic devices for my daughter's tack trunk--however, sit did not withstand the "beating" a tack trunk gets at a horseshow. I have used since then other spring loaded hinges (from rockler--I bought them at the local store) and they are far more sturdy. if you think that you need fairly heavy use or stress, do not use these devices.
What is length of lift o mat support strut 150N compressed and extended?
Tom C on May 3, 2018
What type of hinge is used on a cabinent door with TV mounted on it?
Suzanne U on Apr 23, 2018
I know it says maximum door height 24". Why is that? the door I am wanting to use it on is closer to 40" tall.I know it says maximum door height 24".
Michael D on Oct 2, 2017
I have a built in clothes hamper that opens swinging down with a full overlay face and European hinges,
Will this lift o matt slow the open and/or assist in an up close?
Thank you
Kurt
Kurt H on Feb 16, 2017
Do you have gas springs for a 36" tall door? I am wanting to create operable top-hinge shutters which can open and lock at any degree up to full 90 degree open position. Thanks
Austin W on Dec 28, 2016
Hello. I have completed the Rockler Steamer Trunk plan with a 15.2 lb white maple lid. Lid is 20 inches deep from hinges in back to front edge. I'd like to use 150N LiftOMat gas springs, attached to inside of box side, and other end of lift attached to inside of the side of the lid. My question is: can you tell me specific attach points for both ends of Lift OMat in this application?There will be one gas spring on each side, and I'd like to place them on inside of lid & box to keep them out of the way as much as possible. Don't want to misplace them and mess up nice interior of box/lid.
JohnB on Jan 24, 2016
More Suggestions