$44.99 Each
In stock
Top-mounted guide bearing lets you hand rout with templates in full view.

Rockler Flush Door Trimming Router Bit - 3/4" Dia x 2" H x 1/2" Shank

Item #
25556
Rating:
84% of 100
Rockler Flush Door Trimming Router Bit - 3/4" Dia x 2" H x 1/2" Shank Rockler Flush Door Trimming Router Bit - 3/4" Dia x 2" H x 1/2" Shank Rockler Flush Door Trimming Router Bit - 3/4" Dia x 2" H x 1/2" Shank
Rockler Flush Door Trimming Router Bit - 3/4" Dia x 2" H x 1/2" Shank
With a full 2" of carbide, this bit is ideally suited for trimming thick entry doors, interior doors and countertops. It features a top-mounted guide bearing, which lets you use templates on the top side. This means better visibility when hand-holding the router. The bit is 3/4" in diameter, and features two flutes for efficient chip removal.
(1) Rockler Flush-Trim Door Trimming Bit
More Information
Brand Rockler
Weight 0.2500
Bit Type Flush Trim
Diameter 3/4"
Cutter Height 2"
Shank Size 1/2"
Flutes 2
WARNING: Cancer & Reproductive Harm - www.P65Warnings.ca.gov

WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.
4.2 / 5.0
13 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
9
2
0
0
2
I’m sold on Rockler bits
Works great and leaves a nice finish. Only have about an hour of use so far but the Rockler guarantee will take care of any issues so I’m sure I’ll continue to use and enjoy it.
May 16, 2019
Purchased
4 weeks ago
Woodworking Experience:
Advanced
Great !
WOW, Rockler router bits are amazingly tough I’m going through an inch and a half of plywood and it’s as if they’re getting sharper. Way to go guys these bits rock compared to many others I really put them through a beating
April 6, 2019
Purchased
2 months ago
Woodworking Experience:
Intermediate
Worked perfectly template routing 6/4 walnut stock
August 22, 2017
Purchased
1 year ago
does the job
I needed to trim edges on 11/2 inch stock. I was concerned
using a 2" bit, but it worked great. Very pleased as always with
Rockler bits.
April 19, 2017
Purchased
over 2 years ago
Woodworking Experience:
Intermediate
Great quality bit, happy I found this size.
December 2, 2016
Purchased
over 2 years ago
Woodworking Experience:
Advanced
Router bit review
I used it to make decorative ends from a pattern on multiple trusses for my patio cover. Worked great.
April 25, 2016
Purchased
over 3 years ago
Woodworking Experience:
Intermediate
3/4" Dia x 2" H x 1/2" Shank Trimming Bit
I bought this bit for a specific use. That being to form a perfectly round seat for bar stools constructed from 2"x10" Pine dimensional lumber jointed together with bisquits . Trimming to 1/4" of my line with a band saw, I trimmed then with the router bit. Did great. The bit feels like it will trim the chest hair off of a mad gorilla.
May 3, 2015
Purchased
over 4 years ago
Woodworking Experience:
Intermediate
I purchased this bit to add...
I purchased this bit to add a curve to the inside of the legs of a coffee table. the legs are 1 3/4 square. By attaching a 1/4 MDF template to the legs, I was able to turn my router table into a copy shaper. This bit worked beyond my expectations and produced 4 perfectly matched legs.
August 4, 2011
I purchased the Door Trim Router...
I purchased the Door Trim Router Bit to save time in the construction of several child size rockers. I made templates for the rocker sides & rockers & need a pattern style router bit that will give more than 1-5/8" cutting depth because I am using 2"X6"s for the rockers & doubled up on the 3/4" thick pine sides so they could be cut out together for accuracy in assembly. This router bit worked excellently & saved me from spending loads of time with a jig saw & sander. Excellent Product.
May 22, 2008
It was the missing piece that I needed to finish the job. excellent results
April 19, 2018
Purchased
1 year ago
Woodworking Experience:
Advanced
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 3 questions Browse 3 questions and 15 answers
Why did you choose this?
Rockler Store
make table legs
Joe L on Feb 11, 2019
To flush trim 1-3/4 " laminated maple counter tops.
Douglas E on Aug 8, 2017
make table legs
Joe L on Feb 11, 2019
Used this bit before and had excellent results!
Harold G on Nov 15, 2017
To flush trim 1-3/4 " laminated maple counter tops.
Douglas E on Aug 8, 2017
To use with a project pattern.
Bryan B on Jan 27, 2017
These work perfectly for cutting profiles in the tails of a pergola, especially on large timbers.
Jeff M on Sep 29, 2016
depth of cut
Bruce M on Aug 14, 2016
Would be very helpful in cutting out slots for pocket doors
Ed on Aug 7, 2016
needed 2" length and 1/2" size for pattern shaping of table legs
Robert P on Oct 17, 2015
I am shaping the ends of boards on a pergola, and this lets me make a pattern and replicate it across all the boards easily.
John B on Sep 15, 2015
I chose this bit as I have to cut curves on braces on my first timber-framed construction I am doing (I am not a professional) and as I do not have a bandsaw I need to cut the curves with a combination of my jigsaw/chainsaw and router with this bit using a template guide top and bottom of 3x stock to get the long curves on the braces.
Robert J on Jun 23, 2015
Only place I could find what i needed
Larry M on Jun 13, 2015
I needed a bearing trim bit.
Randy K on May 1, 2015
Used this bit before and had excellent results!
Harold G on Nov 15, 2017
To use with a project pattern.
Bryan B on Jan 27, 2017
Will this bit mounted on a plunge router be able to plunge straight down through the material?
Ben J on Dec 18, 2016
BEST ANSWER: No
What speed would you run this router bit?.
theresa h on Jul 2, 2018
BEST ANSWER: Hi Teresa,
I current run Porter Cable Model 6931 in my custom cabinet shop. One is in Rocklers FX lift and the other I use as a portable . They are both 1 3/4 HP and run at max . Not sure what you are using bit in but would recommend using max rpm . Mine only have an on and off button