Bench Dog® Cast Iron Router Table for Table Saw, Pro Fence and Plate
Expand your table saw's versatility by adding this industrial grade router table in place of the extension wing. Perfect for shops where space is tight, ProMAX includes a cast-iron top, Bench Dog's 28'' ProFence, a miter gauge track that adjusts for a no-slop fit, and a solid aluminum insert plate that is pre-drilled to fit your specific router. If workspace is an issue, the ProMAX has you covered. Its dual fence slot configuration lets you rotate the fence and work from either side of the table to maximize surface area. Plus, with a third miter slot at its disposal, your table saw becomes perfectly equipped to handle crosscut sleds.
Your table saw needs to be 27'' deep and 1-1/2'' thick to work with the Rockler Bench Dog® ProMAX Cast Router Table. The holes on the Promax should match at least three holes on your saw or you may need to drill additional holes in the Promax table. The ProMax mounting hole pattern can be found under Technical Downloads.
Which Router Plate Do I Need?
To choose a pre-drilled plate, find your router below.
Router Plate A:
- Bosch MRC23 Series, 1617-1618
- DeWalt 616-618
- Hitachi M12VC (fixed and kit)
- Makita 1100
- Milwaukee 5615-5624
- Porter-Cable 690
- Porter-Cable 890
- Porter-Cable 7529
- Porter-Cable 97529
- Porter-Cable 8529
- Ridgid 2930 Combo Kit
Note: Current models of the Porter-Cable 892 require at least two screws to be 1/2" long versus 5/8".
Router Plate B:
- Craftsman Standard
- DeWalt DW621
- DeWalt DW621K
- Freud FT 1700E
- Freud 1702VCEK
Router Plate C:
- Milwaukee 5625-20
- Porter-Cable 7518
- Porter-Cable 7519
- Porter-Cable 7538
- Porter-Cable 7539
- Triton TRA001
- Triton MOF001
Router Plate D:
- Bosch 1619-1619EV
- DeWalt 625
- Freud FT2000
If your router is not listed: Choose from two non-drilled plates—one with a 4'' insert ring (#57293), and the other a 4-3/8'' insert ring (#56845)—and drill the plate to fit your router.
- There is an additional $20.00 shipping charge for this item.
- ProMAX cannot be installed as a left extension replacement on left tilt "cabinet" grade table saws because the table saw's motor protrudes to the left. Nor can ProMAX be installed as a right extension replacement on right tilt "cabinet" grade table saws for the same reason. Mounting ProMAX to the far right will avoid the protruding motors, however, ProMAX must be supported with two steel rails that also support your T-square style rip fence and legs.
(1) Pro Fence
(1) Aluminum Router Plate
|Technical Documents||Rockler Bench Dog ProMax Mounting Hole Diameters and Locations
Rockler Bench Dog ProMax Cast Iron Router Table Top Extension Installation
Modifying Promaxrt Router Table For Use With Rockler Pro Lift
7 months ago
9 months ago
11 months ago
over 2 years ago
Very solid table. Flat. High quality cast and machined with precision.
Mounted on the left side of my Ridgid R4512. If you remove the back panel of the saw, and tilt the saw all the way, you have full accessibility to use a small wrench to tighten the bolt that was included with the hardware. It is very difficult to get this done without removing the back panel as the motor bulge on the left side of the saw prevents you from accessing the bolt.
Only wish it had instructions for the router plate install. I went back and forth with Rockler several times before I understood how it mounted - new to this.
But, as stated, tis thing is great!
1 year ago
1 year ago
What a great combination! The table is a must if you are interested in combining a router to your table saw.
1 year ago
1 year ago
The router table is a tank: solid, heavy and flat. The fence is excellent and the entire kit is top quality. At first I thought it was too pricey but once I set it up I realized you really do get what you pay for. Highly recommended.
1 year ago
I just took delivery on a Fusion 2. Nice!
I measure 6" clearance right of the protruding tilt wheel and miter gauge (in storage location).
There are NO screw holes for mounting a router table extension right (or left) of the saw blade.
You will need to drill out or clamp. Left and back of router table you drill steel, front you drill aluminum.
It is a great fit, fairly easy to install, very practical. My only recommendation is you have a buddy help you when installing the metal platen. It is heavy and awkward to try to do by yourself.
New holes had clearance problems, had to cut up transfer punches to fit the Bench Dog table, custom spacers to fit Bench Dog table holes, used Grade 8 bolts, very heavy set up and needs additional supporting legs.
for him real well and that he likes it. As for me I really like and enjoy using the table. ENJOY