WARNING: Cancer & Reproductive Harm - 
VIEW
57022
$9.99
Each
In stock
Lets you mount a router with a 3-1/2'' motor diameter to the Rockler Pro Lift (#52429 and #55803 (coming soon), sold separately).
This adapter sleeve reduces the opening of your Rockler Pro Lift router lift (#52429 and #55803 (coming soon), sold separately), allowing you to mount a smaller 3-1/2'' diameter motor. If you are unsure of your router motor's diameter, check the manual, or measure the circumference with a tailor's tape. Measuring the circumference is easier and more accurate than measuring the diameter. The reducer has an expansion gap, so it will fit motors measuring up to 1/8'' larger or smaller in diameter than the listed spec.
Accepts motors with 3-1/2'' diameter (11'' circumference), including:
- Bosch 1617
- Porter Cable 690 series
- Porter Cable 890 series
- Dewalt 616 and 618
- Others
(1) 3-1/2'' Router Adapter Collar for Rockler Pro Lift
| Weight | 0.3000 |
|---|---|
| Tech Spec |
|
4.0 / 5.0
5 Reviews
Good fit on an older router.
Fit my older Rockwell router perfect.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Router collar
Outstanding, fit perfect.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
This will work fine temporarily until I can afford a larger motor
Perfect fit for my porta cablel
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Not for use with Ridgid routers
Be very careful if you plan to use with a router that is 3 5/8 inch in diameter. I was expanding the Pro Lift to fit a Ridgid router and ended up breaking the bracket on the lift right as it expanded to 3/8 inch. I used calipers to sneak up on the fit but never made it. Mine might be a $370 paperweight now.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Molded so it is hard to place over router housing thus making it difficult to mount router in Pro Lift.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 4 questions
Browse 4 questions
and 21 answers
Why did you choose this?
Rockler Store
I ordered your Pro life and needed the collar to fits my Bosch router base.
Harry V
on Apr 26, 2019
Because the salesperson in the store didn't tell me that I needed it for my lift kit :). Which I discovered when I tried to install my Bosch.
Jon D
on Feb 26, 2019
I ordered your Pro life and needed the collar to fits my Bosch router base.
Harry V
on Apr 26, 2019
Missed the part about needing an adapter to use my router
Scott Docteur O
on Mar 14, 2019
Missed the part about needing an adapter to use my router
Scott Docteur O
on Mar 14, 2019
Hoping this will fit my craftsman router. It is 3.5" in diameter.
Fred L
on Jan 26, 2019
Is this adapter compatible with the previous BenchDog ProLift router lift?
BEST ANSWER: This adapter is compatible with the BenchDog ProLift Router Lift.
- Reply
- Inaccurate
- David Staff on Apr 10, 2018
What is the little Plastic Orange piece in with the Adapter Collar for? It may be black according to which Adapter Collar you have?
BEST ANSWER: it slips into the slot in the ring (from the outside) enabling you to more easily insert the router
- Reply
- Inaccurate
- J b on Oct 12, 2018
- Purchased on Feb 27, 2018
I have a new dewalt 2.25 HP router and I bought the sleeve adapter for my pro lift. Why is my router sliding out of the pro lift? I have the bolts tightened as far as I can.
BEST ANSWER: check the diameter of the router and the pro lift. If it's close you can use a couple layers of masking tape to make up the difference.
- Reply
- Inaccurate
- Mark on May 24, 2019
- Purchased on Apr 7, 2018
Frequently Bought Together