$79.00 Each
In stock
Rip or crosscut panels up to 48'' long—Universal Saw Sled accepts almost any circular saw, left- or right-blade.

Kreg® Accu-Cut 48'' Track Guide for Circular Saws

Item #
46% of 100

Make straight, accurate, splinter-free cuts! With just a circular saw (sold separately) and the included Universal Saw Base and Accu-Cut™ track, you can rip, crosscut and make angled cuts up to 48'' long in plywood, MDF, and other sheet goods—just lay the track on the sheet and slide the saw across. The track keeps the saw moving straight and stays in place without the need for clamps. Setup couldn't be easier—just line up the track with your cut line. Dual guide strips provide zero-clearance protection to prevent splintered cuts. No straight edge on your sheet? No problem. With the Accu-Cut, a straight reference edge is not required, since the track itself is the reference edge. The Accu-Cut™ is portable, too, so you can take your saw to the workpiece and cut with precision, rather than having to handle heavy sheets on a table saw.


  • Rip, cross cut, and make angled cuts up to 48'' long in plywood, MDF, and panels
  • Take your saw to the material instead of having to take your material to the saw
  • Simply align the track with your marks to make accurate cuts
  • Track stays in place without clamps thanks to anti-slip guide strips
  • No splintering—anti-chip strips support material during the cut
  • Begin cuts easily with the included Starting Block to support the saw
  • Universal Saw Base accepts almost any circular saw—left or right blade
  • Universal Saw Base is also compatible with the Rip-Cut™ edge guide (#59199, sold separately)
(1) Universal Saw Sled
(2) 26-1/2'' Aluminum Guide Tracks
(2) Track Connectors
(1) Starting Block
1) Track Indicator Clip
(1) Set of detailed setup and usage instructions
More Information
Brand Kreg
Manufacturer Part Number KMA2700
Weight 5.5500
Tech Spec
  • Maximum Cut Length: 48''
2.3 / 5.0
9 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
alternate ways
altnately you could use a 6 x 3/8 Baltic birch plywood strip for those long rips. the set up time is a bit longer and tha cut might be less accurate but I have to sat plywood costs less...
November 5, 2018
Woodworking Experience:
Problem Solver!
I was not sure what to expect from this saw track. I read other reviews and there were many that had issue with something or another. I took my time to set this up with my good circular saw and even installed a new blade beforehand. The dial in went easy and the first few runs on scrap wood produced the desired results.It definitely makes long, straight cuts much easier. I am happy with my purchase.
April 17, 2018
Woodworking Experience:
Would recommend.
Well made and a very usable design. However, a part is missing. The plastic wrap was secure. I have not been successful in getting a replacement from Kreg. My 15 year old PSI tool is more accurate although more difficult for mounting saw.
January 13, 2018
1 year ago
Woodworking Experience:
Good for precise straight cuts.
I Iike the factthat the track edge is on the cut line. This greatly simplifies the guide set up. While I haven't yet had the track move while cutting I am reluctant to trust the stickiness of the guide. I will use clamps most of the time. The saw setup was fairly easy and it realigns reliably.

I am not sure what type of material is used for part that attaches to the saw and the start line up. I have had too many bad experiences with plastic like parts that turn brittle with time and, as a consequence brake easily. I am especially concerned with the clamps that are used to mount the saw. Both of the plastic like parts have serious stress points when in use. The back of the saw mount hangs loose making a lever fulcrum at the clamp and the start guide has a lever fulcrum where it meets the track. Tiny forces at 10 or so inches from the fulcrum at multiplied several fold. I regard these two points as serious design flaws.
November 23, 2018
9 months ago
Woodworking Experience:
Not for most cordless saws.
As per manufacture it states in the instructions if you have a plastic blade guard they highly recommends not to use this. The shuttle which is mounted to base of the saw is very lose on the rail. The base of the saw is to narrow for the shuttle to fit correctly. Now its going to cost me to send it back!
December 7, 2017
Woodworking Experience:
Rub Goldberg
Bought this thing in Jan. just now getting to use it. The plastic saw plate is flimsy and set up is difficult. If I still had the receipt I'd return it to Rockler's for a refund. I expected much better from KREG.
April 3, 2019
Woodworking Experience:
Dangerously flimsy
The saw base/mount is made of thin, flexible plastic, and tightening the hold-downs will deform the base. It is definitely not compatible with the MK Morse 9" Metal Devil circular saw, but I would be reticent to use it with any other of the several circular saws I use to cut forest products. I am a great fan of many other Kreg tools and am disappointed that the quality I expect from Kreg seemed lacking in this tool, which I returned.
September 11, 2018
Woodworking Experience:
Would not recommend Kreg
I bought this flimsy product to get a straight cut to join a table top. Had some issues with this cheap plastic product so I contacted customer service. Just like on the Jig the plastic is easy to wear and does not last. I asked for two small parts after purchasing two of the Accu Cut products and spending nearly $200. Todd Burton in customer service told me to buy a third product to get the $2 cheap parts I needed. I explained I had purchased several Kreg products and have been a good customer and he had no care in the world. I will never buy another Kreg product. There are too many competitors with better built products who care about customers to deal with Kreg anymore.
August 20, 2018
Woodworking Experience:
What a disappointment. Save your money.
I bought this product based entirely upon my excellent experiences with the Kreg pocket hole jigs.

I was tired of having to clamp my long level onto the workpiece to get an accurate cut. Kreg makes the claim that the non-slip base doesn't require clamping; that, is complete and utter nonsense. You cannot use this device without clamping it to the workpiece. If I have to clamp the Accu-Cut to the workpiece, what have I gained? I might as well clamp my old 4' level onto the workpiece as I alway have and save myself $80. I simply can't see any advantage to using this device.
February 11, 2018
Woodworking Experience:
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 7 questions Browse 7 questions and 8 answers
Why did you choose this?
Rockler Store
Don't have the space to use my table saw to cut larger items so I hope to use this with the track horse.
LR B on Jan 20, 2019
hugo S on Jun 5, 2018
Don't have the space to use my table saw to cut larger items so I hope to use this with the track horse.
LR B on Jan 20, 2019
My husband put it on his wishlist.
Kathy B on Dec 8, 2018
hugo S on Jun 5, 2018
Because I need it.
Starr P on May 9, 2018
Looks to be an accurate way to cut straight lines on plywood at any angle. The way it grips the plywood will be very easy to use. Thank you.
Larry H on Feb 21, 2018
Christmas Gift
Kevin S on Dec 9, 2017
Christmas gift for Son.
Barbara C on Nov 29, 2017
Breaking down plywood easier. Like KREG products
Steve M on Oct 27, 2017
My husband put it on his wishlist.
Kathy B on Dec 8, 2018
Because I need it.
Starr P on May 9, 2018
is this compatible with worm gear type saws such as Skil ?
R L on Nov 15, 2017
BEST ANSWER: Hello. Unfortunately, the sled on the Accu-Cut is not compatible with any worm-drive circular saw. It will work with most 7-1/4" circular saws. Thanks, Josh.
Can two of these be put together to produce an eight foot cut?
Eric K on Nov 10, 2017
BEST ANSWER: Hello. We do not recommend connecting Accu-Cut tracks together. This item was designed to work in Cross-Cut applications up to 4 foot. If you need a tool to rip 8 ft pieces, I would recommend using the Rip-Cut (KMA2685). Thank you, Josh.
And can the rip cut 24 be used with the cordless dewalt 60v circular saw?
Vincent A on Jul 12, 2018
I cannot say with any certainty if the saw will be compatible with the Accu-Cut's sled. Here are a few things to be mindful of when determining if a saw will be compatible with the sled. Make sure that the saw base is at least 5-1/2 to 6 inches wide or more. There should be at least a 1/2 inch or more of open space on the front of the saw base or shoe across the with of the saw's base plate so that the sled can latch on to it. Some saws have a tilt mechanism on them and it consumes a lot of space. If the saw base plate curves upward around the edges, make sure that it is no higher than 3/8 of an inch. Avoid worm drive saws and saws with plastic blade guards. Saws with plastic blade guards creates excessive vibration.
Can it be used with the cordless dewalt circular saw?
Vincent A on Jul 12, 2018
BEST ANSWER: I have not tried it but if your Saw has a Metal Blade guide I would think that it would Work because the Accu-Cut can be used with most Saws on the Market
Makita 165mm saw .will this fit? Also I have heard that it's awkward to fit to the base plate
Paula J on Jun 4, 2018
BEST ANSWER: That saw won't fit well. The Rip cut needs the saw to have a couple of flat, clear spaces about 5/8" back from the front edge of the base plate for the lock-downs to clamp down upon.
Does this item have the capability to attach a router, or could one fabricate a base plate that could attach a router to the track guide?
Larry B on Nov 16, 2017
BEST ANSWER: Hello. Unfortunately no, this is designed strictly to be used with a circular saw. I do apologize for any inconvenience that this may cause. Thanks, Josh.
Can this be used with a jig saw?
Joseph R on Nov 15, 2017
BEST ANSWER: Hello Joseph,
I am sorry to say, the Accu-Cut is not designed to be used with a Jig Saw.
Thank You,
Billy H
Kreg Tech Support
More Suggestions