VIEW
53522
$229.99
Each
In stock
Premium fabric pleats filter dust down to an incredible 1 micron in size!
With this one simple upgrade, you'll increase the filtration of your Wall Mount Dust Collector by up to 30 times, giving the air quality in your shop a welcome boost. The premium pleated filter captures dust down to 1-micron in size, compared to 30 microns for the stock filter bag, and 5 microns for the upgraded filter bag. Better filtration amounts to better safety for your lungs. You also get the convenience of a crank-style filter cleaner—just turn the handle to clear dust off the pleats. Last but not least, the dust now drops neatly into an included plastic bag for easy emptying.
Features:
- Use with the Rockler Wall Mount Dust Collector (#42400, sold separately)
- Steel frame with fabric pleats on the inside
- Rubber gaskets for a tight seal to your collector
- Large handle rotates an agitator to clean dust off the pleats
- Agitator handle folds flat to minimize obstructions
- Strap clamp and plastic collection bag included
(1) Dust Right® Canister Filter for Wall Mount Dust Collector
(1) Mounting Bracket
(1) Plastic Dust Bag
(1) Mounting Bracket
(1) Plastic Dust Bag
| Brand | Rockler |
|---|---|
| Weight | 18.0500 |
| Tech Spec |
|
| Technical Documents |
WARNING: Cancer & Reproductive Harm - www.P65Warnings.ca.govWARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.
4.6 / 5.0
41 Reviews
Does an amazing job in my 231 Square foot shop
I have a smaller basement shop and didn't want to run PVC pipe everywhere as wall space was limited and the height of my ceilings was only 8 feet. Most of my tools are mobile so I just needed a solution that would allow me to move from one tool to the next pretty easily. I don't have any ventilation in the room so it was important to get a really good filter in addition to the air filters I currently have running.
I bought this Unit in addition to the wall mounted Dust Deputy and it has been amazing. The directions aren't the clearest in the world (as others have stated) but it was fairly easy to figure out.
The hand crank does a good job of knocking debris / dust out of the filter. My only complaint is the inside piece that rubs against the filter only makes contact in a few places. It would be better IMO inf the clips made contact in all places while spinning. This would clear it even better.
The pics are of all the stuff I purchased when installing the unit.
I bought this Unit in addition to the wall mounted Dust Deputy and it has been amazing. The directions aren't the clearest in the world (as others have stated) but it was fairly easy to figure out.
The hand crank does a good job of knocking debris / dust out of the filter. My only complaint is the inside piece that rubs against the filter only makes contact in a few places. It would be better IMO inf the clips made contact in all places while spinning. This would clear it even better.
The pics are of all the stuff I purchased when installing the unit.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Pricey but lungs worth it
I have no way of measuring the effectiveness of the canister so have to trust specs. Much cleaner air in shop compared to 30 micron bag. Should actually filter finer materials as the pores gradually fill. Wish I had mounted it with a quick disconnect connector so I could take it outside to clean with compressed air occasionally.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (1) No (0)
- Flag as Inappropriate
Worth the money
I love that you just have to crank the handle a couple times and the internal paddle removes all the small dust particles from the filter. This insures there is no loss of suction.
- Was this review helpful? Yes (2) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (2) No (0)
- Flag as Inappropriate
Great filter works well with the dust collector
- Was this review helpful? Yes (0) No (1)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (1)
- Flag as Inappropriate
Works well cuts down on the dust compared to the 5 micron filter bag I had on before.
Increased the suction, but also increased the noise some, worth the increase in noise.
My only complaint is i ordered this after looking at the early Black Friday ad and this filter was not in it so I when ahead and ordered it thinking it would not be on sale during the holiday sales ,the next sale ad had a $50 gift card included.
If hadn’t of have a large amount of projects to get completed
I would have waited for it to go on sale.
Increased the suction, but also increased the noise some, worth the increase in noise.
My only complaint is i ordered this after looking at the early Black Friday ad and this filter was not in it so I when ahead and ordered it thinking it would not be on sale during the holiday sales ,the next sale ad had a $50 gift card included.
If hadn’t of have a large amount of projects to get completed
I would have waited for it to go on sale.
Should have waited
Great filter
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (1)
- Flag as Inappropriate
Helps keep my garage workshop clean and filters the really nasty fine sawdust.
Great addition to their dust collector. Highly recommended.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
better dust control
I have been planning on a dust collector upgrade for some time. I planned on adding a second stage system when I spotted the duct collector. Big improvement.
- Was this review helpful? Yes (2) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (2) No (0)
- Flag as Inappropriate
Good product to add to dust collector increase suctioning twice
- Was this review helpful? Yes (0) No (3)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (3)
- Flag as Inappropriate
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 27 questions
Browse 27 questions
and 49 answers
Why did you choose this?
Rockler Store
Does the filter ever need replacing?
BEST ANSWER: no, it is cleanable though. You get the convenience of a crank-style filter cleaner—just turn the handle to clear dust off the pleats.
- Reply(1)
- Inaccurate
- Steve Staff on Sep 16, 2016
Does Rockler sell the plastic collection bags for the new canister and, if so, how much are they?
BEST ANSWER: Yes, a pack of 3 is available for $9.99 as item # 55408
- Reply
- Inaccurate
- Steve Staff on Sep 16, 2016
What are the dimensions of the canister?
BEST ANSWER: 5" inlet that attaches to DustRite, Top Diameter is 15", Bottom Diameter is 15 1/4", Cannister is 17" high.
- Reply
- Inaccurate
- Steve Staff on Sep 16, 2016
How long is the plastic bag for the canister?
What is the CFM/ back pressure design of this filter?
I have a Rockler wall mount vacuum. Does this filter with plastic bag replace the original bag?
What is the diameter of the bag opening?....if it's is right I could place this on top of my collector in stead of a filter bag, just need a plate to close off the 5" port.
BEST ANSWER: 5" inlet that attaches to DustRite, Top Diameter is 15", Bottom Diameter is 15 1/4"
- Reply
- Inaccurate
- Steve Staff on Sep 16, 2016
I want to use this filter with my Dewalt planer that has its own built in chip/dust blower that is very powerful. Therefore, I do not need the Dustright vacuum; only the filter and bag. It seems that the inlet diameter is 5". Is that outside diameter or inside? Does anyone sell an adapter that would allow the connection of either a 2-1/2" or 4" dust hose to that inlet?
BEST ANSWER: The flange on the filter for your purpose is indeed a 5" female flange approximately 1" high, with a clamp allowing it to be tightened around a 5 in O.D. Pipe. Not really sure where you would find a 5" O.D. tube that would adapt to air hose, but that would be the least of your problem, in my opinion. Even with a "blower that is very powerful" as you state, my experience leads me to believe that you could not "BLOW" the air through corrugated tubing without it fouling up inside. Remember also that you will be dealing with "Head Pressure" when blowing. No "Head pressure" exists when "PULLING" the air. Pulling dust and chips thru a hose in exponentially easier that pushing it, even if the inside surface of the tube were smooth.
Hope this helps.
Tom
Hope this helps.
Tom
- Reply
- Inaccurate
- Thomas B on Aug 8, 2017
- Purchased on Aug 15, 2016
I have a wall mount collector that looks like yours, it is made by Grizzly, and has a four inch outlet for the bag…Will this filter maybe work on my collector???
Will this work with the Shop Fox W1826 Wall Dust Collector?
BEST ANSWER: Alexander, The answer from me is "possibly". I know this canister filter was specifically designed for the Dust Right wall mounted dust collector, however I was able to retrofit it to the Harbor Freight 1HP dust collector using a 4" ABS coupling I found Lowe's. If that Shop Fox exhaust port has the same outer diameter as the Dust Right unit, you might be in business. Otherwise some innovation might be in order.
- Reply
- Inaccurate
- Tom B on Nov 11, 2016
- Purchased on Sep 12, 2016
Does this filter, couple with the Dust Right Wall Mount Dust Collector eliminate the need for an air filtration system? I see stand alone air cleaning systems from Jet and Powermatic. Not sure how to determine if I need that as well.
Dust Right® Canister Filter for Wall Mount Dust Collector
BEST ANSWER: I do not think so. All machines will leak some dust despite the best vacuum system you can devise. I make sure to run my air filter ration system when machining wood, and I leave it on for a few hours afterwards once the shop is closed up.
- Reply
- Inaccurate
- Steve R on Nov 4, 2016
- Purchased on Aug 20, 2016
I do sandblasting in a blast cabinet. How well would this work with the blasting dust? I use a shop vac right now. Thank you.
BEST ANSWER: I can only speak to my more conventional setup in using this filter with the wall-mounted collector as being very effective in saw dust collection for table saw, router table, and miter saw. I suspect your blasting dust is much finer than saw dust and so some might get through the filter. There is a little leakage around the fittings for me, but it is minimal. There would also be the concern of the fine dust getting into the bearings of the dust collector.
- Reply(1)
- Inaccurate
- Michael T on Oct 16, 2016
- Purchased on Sep 3, 2016
Do you also carry those plastic bags? I mean if I'd like to buy more of em
BEST ANSWER: Yes, a pack of 3 is available for $9.99 as item # 55408
- Reply
- Inaccurate
- JOhn F on Apr 9, 2018
I have a Delta floor/wall mount dust collector with a 5" outlet. Will this work ?
Do you have to use Rockler bags?
BEST ANSWER: I've used the delta bags and they work fine. The way the gasket and lock collar work, you could make a lot of different bags fit.
- Reply
- Inaccurate
- NATE T on Jan 3, 2019
- Purchased on Jan 8, 2017
What happens when the filter is exhausted? Is it $199 for a replacement?
BEST ANSWER: The filter has an internal device for cleaning (use handle to operate) so the filter should operate for a very long time. I assume that it will eventually wear out and would need to be replaced then. But this should not be frequent and I think the cost would be the price of a new one unless they can come up with a way to replace the media only..
- Reply
- Inaccurate
- Paul Z on Nov 15, 2017
- Purchased on Aug 8, 2016
How many square feet of filter material does this filter have?
BEST ANSWER: That is one for the manufacturer.
This has worked well for my small shop, but I did find its limit. Cutting ½ x 1 ½" dados in 8/4 ash for breadboard ends was too much for the unit - the saw ((SawStop Contractor) and air filled with dust. Without the Canister, the Wall mount might have been OK, but I had by then already gotten rid of my collection bag for the wall mount. Up until then, it has taken everything I have dished at it with my table saw, router table, 13" planer and 6" jointer. In the future, I will make cuts like that in smaller bites.
This has worked well for my small shop, but I did find its limit. Cutting ½ x 1 ½" dados in 8/4 ash for breadboard ends was too much for the unit - the saw ((SawStop Contractor) and air filled with dust. Without the Canister, the Wall mount might have been OK, but I had by then already gotten rid of my collection bag for the wall mount. Up until then, it has taken everything I have dished at it with my table saw, router table, 13" planer and 6" jointer. In the future, I will make cuts like that in smaller bites.
- Reply
- Inaccurate
- Steve R on Mar 1, 2017
- Purchased on Aug 20, 2016
Will this filter work with a 2 HP Harbor Freight DC or will it significantly decrease CFM?
BEST ANSWER: I put this filter on my 2HP Harbor Freight unit and added a separator. It does decrease CFM but for my small setup it wasn't a big issue. If you have your unit piped throughout your shop or have long runs i wouldn't recommend it.
- Reply
- Inaccurate
- Mark J on Jan 31, 2017
- Purchased on Sep 1, 2016
Will this work with Shopfox version of this wall mounted dust collector?
I have the older style "floor" dust collector, that I have since wall-mounted. Looks to be the same casing and motor - true? Does this work for that model wall mounted?
BEST ANSWER: This should work fine. I have found this filter has to be cleaned often.
- Reply
- Inaccurate
- BRUCE C on Dec 19, 2017
- Purchased on Aug 18, 2016
I have a shop fox dust collector will it fit . . It's wall mount?
BEST ANSWER: I suspect it may not be a direct fit; but if you're ingenious enough I think you should be able to adapt it... need to consider the overall diameter of the Rockler filter before trying anything...
- Reply
- Inaccurate
- Paul Z on Apr 18, 2017
- Purchased on Aug 8, 2016
I have model 25344 from Rockler does it fit this too?
Does this addition to the dust right wall mount system impact the portability of the system? In considering dust right vs. Shop fox wall mount, I am drawn to the simplicity of moving this u it around the shop via extra brackets.
Dust Right® Canister Filter for Wall Mount Dust Collector
Building my first woodshop. What is the advantage of combining the Dust Right Filter with the Dust Right Dust Collector...compared to the Dust Collector standalone? For the price of the filter, I might as well buy a ceiling air filtration system instead. Or, do i need both types of filtration running simultaneously?
Will this fit on similar Rikon model (60-105)?
Will it fit Rockler Dust Collector Model 25344 ?
Frequently Bought Together
More Suggestions