Small Toggle Clamp
A toggle quick-action hold-down clamp for jigs or for securing a workpiece.
Item #
20787
Once attached to a bench or fixture, this clamp is simple to use and ideal for light-duty applications. With up to 150 pounds of clamping pressure, it works great as a quick-action hold-down clamp for jigs or for keeping workpieces in place.
Features:
- Bottom of rubber clamp foot adjusts from level with mounting surface to 7/16" below mounting surface
- Total length with arm extended: 2-5/16"
- Length of arm only extended: 1-1/4"
- Mounting plate is 1" W x 1-1/16" L
(1) Small Toggle Clamp
| Brand | Rockler |
|---|---|
| Weight | 0.1500 |
| Tech Spec |  |
| Discountable | Yes |
| Clamp Pressure | 150 lbs |
4.5 / 5.0
15 Reviews
A gentle shift in purpose!
My home theater needed something to hold shut the entry drapes without damaging the fabric. After many gadgets, I settled on this little device. It is superb!
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Great clamps for jigs for tablesaw and router table work.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Holds things down with power
I made a sled for the router table. It is used for making cuts on cabinet door stiles and rails. This clamp is perfect for holding the board in place while making the pass through the router bit.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Perfect for my custom jig
I needed to cut some small pieces of trim (4 of them) a very small amount and exactly the same. I needed to make a jig to carry the pieces across the table saw with the unguarded
blade at a 45* angle. No way could I put my hand that close to the blade and hold the trim perfectly square without it. I used the toggle clamp to hold the trim on my miniature sled and it kept them perfectly still.
blade at a 45* angle. No way could I put my hand that close to the blade and hold the trim perfectly square without it. I used the toggle clamp to hold the trim on my miniature sled and it kept them perfectly still.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Its the first time I'd use...
Its the first time I'd use a clamp on a jig and I don't think I'll ever go back to the old way of doing it. They worked great.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
February 7, 2008
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
I make many jigs and fixtures...
I make many jigs and fixtures in my shop for routing and especially on the CNC machine. The toggle clamps are fantastic. easy to install and adjust right clamping pressure to assure accurate hold downs and fast fexible wood changes. I have an assortment for ready use as the jigs dictate.
- Was this review helpful? Yes (1) No (0)
- Flag as Inappropriate
January 20, 2008
- Was this review helpful? Yes (1) No (0)
- Flag as Inappropriate
I had purchased a pen press...
I had purchased a pen press kit from another supplier and after a couple of months, the press mechanism bent and became useless. I replaced the press mechanism with a "Large Action Push Clamp" #32103 and doubt I will ever have to replace it again. This push clamp is built to last!! Great product!
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
January 3, 2008
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
I am a retired tool &...
I am a retired tool & die maker. We used the toggle clamp in the machine shops and now in my wood shop. They are great for holding parts in jigs and fixtures.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
December 21, 2007
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Great for homemade jigs.
Great for homemade jigs.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
November 17, 2007
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions
Browse 2 questions
and 2 answers
Why did you choose this?
Rockler Store
will this clamp take a 1/4-20 standard threaded swivel foot?
BEST ANSWER: Nope. I tried to push a 1/4-20 bolt through the clamp, and it wouldn't pass through.
- Reply
- Inaccurate
- JOE V on Jan 31, 2016
- Purchased on Mar 27, 2015
Can you show a picture of the clamp in completely open position? Or tell me how far is the maximum travel from closed to complete open? Thank you.
BEST ANSWER: When opening the clamp, the clamping arm pivots up and back.
At the fully retracted position, the clamping arm is out of the way and has swung up and over, past vertical, slightly toward the rear of the clamp. This leaves the are in front of the clamp completely clear.
The toggle handle also swings up and over the clamp, and lies nearly flat at the back of the clamp.
At the fully retracted position, the clamping arm is out of the way and has swung up and over, past vertical, slightly toward the rear of the clamp. This leaves the are in front of the clamp completely clear.
The toggle handle also swings up and over the clamp, and lies nearly flat at the back of the clamp.
- Reply
- Inaccurate
- JOE V on Apr 8, 2015
- Purchased on Mar 27, 2015
WARNING: This product can expose you to chemicals including DEHP which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Related Products
More Suggestions
