VIEW
GRP18537_1
In stock
These wood fillers closely emulate the properties of real wood. They can be stained, sawed, drilled, sanded, planed and nailed, just like the real thing.
Made from genuine wood flour, these fillers closely emulate the properties of real wood. They can be stained, sawed, drilled, sanded, planed and nailed, just like the real thing. They show no noticeable signs of shrinking or cracking, so you'll only have to apply it once for a smooth repair. It spreads smoothly and evenly, and sinks into gaps. No mixing is required, and it dries in only 15 minutes. Suitable for interior or exterior use. Available in 10 colors.
Instructions for use:
Instructions for use:
- Match wood filler color to unfinished wood. Always test filler, stain and finish combination on small area
- Press wood filler into defect
- When dry, sand flush with surrounding surfaces
- Sand and finish after approximately 15 minutes
- Must be shipped within 48 Contiguous United States.
(1) Famowood Wood Filler, 6oz
| Brand | Famowood |
|---|---|
| Tech Spec |
|
| Technical Documents | |
| Size | 6 oz |
WARNING:This product can expose you to chemicals including wood dust and crystalline silica which is known to the State of California to cause cancer. For more information go to https://www.p65warnings.ca.gov
4.3 / 5.0
65 Reviews
Famo is my go to wood filler. It sands well and accept stain better than other brands.
Lee
Cave Creek, AZ
Lee
Cave Creek, AZ
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
prevent drying and reconstitute
Best filler I have encountered in terms of accepting stain. The only drawback is the rate at which it dries out in the can. I'm the type of person who likes to keep things until they are completely used (instead of throwing away and buying new). From the reading I've done, if the product begins to harden in the can, the best way to reconstitute it is to add some M.E.K. (Methyl Ethyl Ketone). It won't dry out as quickly as acetone. If you can't find MEK, then lacquer thinner is a good 2nd choice.
- Was this review helpful? Yes (3) No (0)
- Flag as Inappropriate
March 4, 2019
- Was this review helpful? Yes (3) No (0)
- Flag as Inappropriate
Cherry Wood Filler
Not much to say - it'a a wood filler, and it filled wood very nicely. Dries pretty quickly, easy to sand. Not much more you could ask.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
wood filler
This is the first time I ever used this type of wood filler, and it really works well.
- Was this review helpful? Yes (1) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (1) No (0)
- Flag as Inappropriate
Best Wood Filler
I have tried many wood fillers but this is the best one I have found. Applies nicely, sands smooth. You will have a hard time finding the repairs.
- Was this review helpful? Yes (1) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (1) No (0)
- Flag as Inappropriate
Famwood is the best wood filler I have used.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Best buy for wood filler.
I've used this item years ago and works as well now as it did then. It fills well and sands smooth plus it excerpts stain reasonably close to wood color.
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Excellent product
Used this product to repair and fill some small spots on maple I am working. You can barely detect it after sanding
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Good product
This wood filler works well and sands down really well, but drys out in the can very quickly!!
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
- Was this review helpful? Yes (0) No (0)
- Flag as Inappropriate
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 30 questions
Browse 30 questions
and 96 answers
Why did you choose this?
Rockler Store
Use it frequently
Arnold G
on Jul 22, 2018
Ship it all when you get the filler.
The answer to this should be obvious. Too fill some places in ash wood.
The answer to this should be obvious. Too fill some places in ash wood.
Bob K
on Aug 7, 2018
I ordered this wood filler because I have not been satisfied with the local box stores type and wanted to try something else.
Don A
on Jul 22, 2018
What color matches redwood best ?
BEST ANSWER: if you cant find redwood putty try red oak
- Reply
- Inaccurate
- phillip m on Mar 2, 2018
- Purchased on Sep 30, 2017
I may need to fill in a section of a guitar body made of alder and stain ? how will this receive the stain versus the wood ?
BEST ANSWER: In my use of this and others it does not stain like the surrounding wood. It appears lighter. I have not found one that matches the wood I am filling. The closest I have come is using the saw dust of the piece I am working on with a little glue to fill with and this doesn't work that well either
- Reply
- Inaccurate
- Regina M on Feb 7, 2017
- Purchased on Apr 29, 2015
When staining should I buy the color I want to stain or the type of wood it is?
BEST ANSWER: Get the right kind of wood. I've always had trouble getting the results I am happy with by staining. You can't make pine look like walnut. This is a great product. Get the closest color. I keep 3 different colors on hand. If it starts to dry out, add a little acetone. Dan
- Reply
- Inaccurate
- Daniel H on Oct 5, 2016
- Purchased on Nov 17, 2014
Can you use famowood to patch knot on a cutting board?
BEST ANSWER: You might want to try Quickwood.
It's an epoxy wood filler that is very tough
It's an epoxy wood filler that is very tough
- Reply
- Inaccurate
- Rick H Staff on Oct 23, 2015
I am refinishing bedroom furniture manufactured by Hickory Furniture Company. The furniture was produced using Paldao Veneers. What is the best color to use to fill some dents?
BEST ANSWER: Hi carol. You didn't say what color the furniture is. Just pick out something close. It can be stained. If famo gets too thick, add a little acetone to thin. I have this product in 3 colors and love the results.
- Reply(1)
- Inaccurate
- Daniel H on Aug 8, 2016
- Purchased on Nov 17, 2014
Can this Famowood wood filler be thinned slightly and used as a pore filler?
BEST ANSWER: i would not try using this as grain filler. I can be thinned with acetone if it gets too thick but since it is acetone based it dries real fast. I love Wood Kote WoodPerfect grain filler. It is mineral spirit based. Dan
- Reply
- Inaccurate
- Daniel H on Jun 20, 2015
- Purchased on Nov 17, 2014
Retailer seems not to have solvent for cleanup. Will lacquer or paint thinner work ?
BEST ANSWER: The Rockler item number for Famowood Solvent is 54684.
- Reply
- Inaccurate
- David Staff on May 28, 2015
I am finishing an oak dining table. While sanding the old finish I found places where the veneer was deteriorated in small areas. Does anyone know if this will work for essentially surface filling these areas?
BEST ANSWER: I use the Famowood Wood Fillers when ever I do not make my own(about 50%). They are a good filler, I would try it in an inconspicuous spot and see how it does. Sometimes another color works like Alder. You can also try thinning the filler with wood filler solvent to thin it a bit. Good luck
- Reply
- Inaccurate
- Robert M on Oct 15, 2018
- Purchased on Oct 25, 2016
Can this be used to repair an already finished piece?
BEST ANSWER: I use it before finishing. The Finish makes it harder & look more like the original wood (if you matched it correctly).
- Reply
- Inaccurate
- David on Aug 5, 2017
- Purchased on Sep 17, 2015
I have a wooden staff that has cracks in it i want to fill then use resin to get a shine. is this the stuff i use?
BEST ANSWER: I have used Famowood for decades on fine furniture and wooden gifts. It finishes well after sanding with 220 grit sandpaper. I would not hesitate to use it.
- Reply
- Inaccurate
- Robert M on Jul 28, 2017
- Purchased on May 3, 2016
I will attempt to fill parts of knot holes in new pressure treated decking. After that I plan to either stain the decking with a light stain or some type of deck treatment. Which of your products would you recommend and what short falls may occur?
BEST ANSWER: It may not weather well. It generally works best when used with a top coat of some kind to seal the wood from the atmosphere. Being that it will be used on exterior (I'm assuning) decking it will be subject to harsh weather and may not last very long. Colored urethane caulk could also be used as an alternative.
- Reply
- Inaccurate
- BRANDON A on Jun 9, 2017
- Purchased on Jun 15, 2015
Is this product moldable? I need to repair a cabinet corner my dog chewed off. Thanks.
BEST ANSWER: Doesn't seem like it would be the best for this. Unless you can work blazingly fast, or in small bursts. Product begins to dry almost immediately after coming out of the container.
- Reply
- Inaccurate
- Cindy J on Mar 29, 2017
- Purchased on Mar 7, 2017
I am building a console table using oak. My oak is 14 inches wide and 2 inches thick but I need it to be 1.5 inches thick. The only way to do this is to cut the piece in half then rip each piece to give me the 1.5inches thick pieces. Then I will have to join the two pieces again to give me the 14 inch wide table top. Will this wood filler work to cover the seam that will be downy he middle? Every time I use wood filler, it is very visible after I stain. Since i'm using an expensive wood, I don't want to mess it up.
Thanks!
Thanks!
BEST ANSWER: Me personally I would plane the item down to 1.5" on a planer. A lot of them only go to 13" wide, but I would try a local hardwood store, usually they have the equipment there and will do it for you for a few bucks. If you have to do it your way, I would suggest applying wood glue in the seam and sanding the area so the sawdust get into the seam and let that dry and sand the area again to remove any glue residue. Famowood is the best filler out there by far, but no wood filler matches the exact wood your using. The same species wood comes in a variety of different shades, thats why its best to use the sawdust from the workpiece your using.
- Reply(1)
- Inaccurate
- Darrin D on Oct 19, 2015
- Purchased on Nov 18, 2014
What advantages would there be for choosing the Latex based filler or the solvent based filler? Is there a performance difference?
BEST ANSWER: I strongly prefer solvent based as it dries quickly. Can get on with project with little down time.
- Reply
- Inaccurate
- Lori O H on Apr 30, 2018
- Purchased on May 2, 2016
Can Famowood be used to fill large voids in vertical surfaces? I have a historic house that has termite damage to the 8” baseboards on a corner. About 3/4 of an inch on both sides of the corner need to be rebuilt. Planning to finish with an oil stain and poly. Is Famowood the best choice! Thanks!
BEST ANSWER: I have used Famowood for smaller repairs. For structural repairs of areas that large, I recommend that you buy the 2-part epoxy (which Rockler sells in soft plastic tubes) that will take stain, and then add a drop or two of concentrated wood dye (also sold by Rockler) to the epoxy mixture when you squeeze it out of the tubes to mix it. I have used this epoxy to repair deep gouges and cracks in a wood floor that I re-stained with dark walnut and then varnished. An epoxy repair of this type, with tinted epoxy, will not "accept" any significant additional stain, so you will need to test the tinting to get the desired color.
- Reply
- Inaccurate
- JEFF D on Jan 16, 2018
- Purchased on Jan 18, 2016
i am looking for a wood filler that matches poplar wood before I stain it?
BEST ANSWER: Best results, to add some stain to the wood filler before you apply it
It will help to make the wood filler match the stain your applying.
It will help to make the wood filler match the stain your applying.
- Reply
- Inaccurate
- RICH C on Apr 16, 2018
- Purchased on Mar 6, 2018
Is this product usable on teak?
BEST ANSWER: Clean the area to be filled with acetone prior to applying the famowood.
- Reply
- Inaccurate
- Stephen M on May 27, 2017
- Purchased on May 31, 2015
I have a gun stock that has a small chip next to the butt plate. Would thie appropriate color of this product be advisable to use to fill the chip? Would this product accept any additional staining, graining, and finish? Thanks!
BEST ANSWER: I use this on my redesigned furniture. The truth is I have never been a to get it to accept stain so as not to stand out. I have not found one yet that will. I have had my best results when I use the saw dust from a the project mixed with glue a and even then it is only 75 percent acceptable.Enter
- Reply
- Inaccurate
- Regina M on Apr 17, 2017
- Purchased on Apr 29, 2015
Is this food safe once it fully dries?
BEST ANSWER: Sir, I never use fillers on food surfaces. My reason, I am not certain how safe it is.
I use good jointers, saw dust with glue, and lots of sanding.
I use good jointers, saw dust with glue, and lots of sanding.
- Reply
- Inaccurate
- Hal D on Mar 13, 2017
- Purchased on Apr 9, 2015
I have a 3/16th crack in my farmhouse table going the entire length. The table is stained and lacquered. Is this product suitable for filling the crack?
BEST ANSWER: Yes, but you will probably have to sand [with 0000 paper] the rest of the table as well, carefully tint the filler [you can use water based tints] and re-lacquer.
- Reply
- Inaccurate
- Nicole L on Jun 18, 2017
- Purchased on Mar 26, 2017
I have a gouge in my oak table top. Will Famowood hold in small narrow channel? It is about half the circumference of a dime. Also, the stain in my table is honey oak. Famowood comes in colors but it says it is stainable. Is there one particular color I should use? Or, just choose the closest to my project?
BEST ANSWER: I used famowood a lot . I would put a couple of coats on. Sand it smooth. Try getting the stain closer to the wood. White or red oak.
- Reply
- Inaccurate
- John S on Feb 7, 2017
- Purchased on Apr 6, 2015
I have an old poplar wooden bowl with a 4" section of insect damage that was really "fluffing up" . I stabilized with a wood petrifier and would like to fill in the almost quarter inch depression. I will have to blend to match color as best possible, what can you use to tint this filler? Also one good thing the bottom of the bowl is very blacken almost as if burnished? Can this stuff be blacked as such with a torch, rubbed with charcoal
?
?
BEST ANSWER: try sanding then use maple
- Reply
- Inaccurate
- phillip m on Mar 2, 2018
- Purchased on Sep 30, 2017
What color matches natural oak best seams in floor?
Can this be used to patch a chip in a maple guitar neck....... has anyone done this?
BEST ANSWER: Hi Bob, if at all possible and especially on the edge of a fret board or at the tuners use a piece of hard maple with Titebond two. If out in the field or contoured section of neck it will work well but sand area to get good bond and fill. Too match color that you can mix with Famowood use Transtint always available at the Rockler store.
- Reply(1)
- Inaccurate
- Richard H on Jul 8, 2016
- Purchased on Dec 5, 2014
what color most closely approximates ash wood?
BEST ANSWER: Maple. Birch would probably work too
- Reply
- Inaccurate
- Tom M on Apr 6, 2016
- Purchased on Nov 9, 2015
May this product be used for joints between plywood and mdf ?
BEST ANSWER: It should do well in that application. Both plywood and mdf are fairly stable products
- Reply
- Inaccurate
- BRANDON A on Jun 9, 2017
- Purchased on Jun 15, 2015
which color matches pecan finish the best? thanks
i am going to use this product at the edge of an undermount sink area, will this product erode over time due to water contact?
If so is there another product I should use?
If so is there another product I should use?
BEST ANSWER: You could try a product called quikwood #25768 and #25778. this is an epoxy wood filler that you can stain or paint and is rock hard and tough
- Reply
- Inaccurate
- Rick H Staff on Oct 6, 2015
What filler would be the best match for filling redwood?
More Suggestions
The answer to this should be obvious. Too fill some places in ash wood.